máquinas injetoras usadas para venda

Inv. Num. : 6248 Type: A 270S-350-60 Producer: Arburg Generated: 2001 Parameters: Operating hours: 47,000 h Clamping force: 35 t Screw diameter: 22 mm Injection capacity: 30 cm³ Injection mass: 27 g Maximum spray pressure: 2340 bar Min. mould height: 175 mm Equipment: Spares Technical documentation The machine has sealed hydraulic blocks. partial replacement of hydraulic hoses Integrated side transducer Integrated sorting flap

Inv. Num. : 5849 Type: IS 220 GN Producer: TOSHIBA Created: 2002 Parameters: Clamping force: 2150 kN Screw diameter: 50 mm Injection capacity: 490 cm³ Injection mass: 450 g Min. height of the clamping plate: 870 mm Min. width of the clamping plate: 820 mm Distance between stands (horizontal): 610 mm Distance between stands (vertical): 560 mm Ejector force: 140 kN Ejector stroke length: 800 mm Maximum spray pressure: 201 MPa Opening the mold: 1060 mm Machine length: 5900 mm Machine width: 1340 mm Machine height: 1840 mm Spray weight: 8600 kg

Inv. Num. : 6278 Type: ES 750/175 HL Producer: ENGEL Generated: 2001 Parameters: Clamping force: 155 t  ... mais informação

Inv. Num. : 6167 Type: GUIDANCE LWF 1300 -SV Producer: Leadway Created: 2016 Parameters: Clamping force: 130 t Screw diameter: 35 mm Distance between stands: 470x420 mm Ejector force: 45 kN Screw stroke length: 120 mm Mould height: 450 mm speed: 320 1/min Machine length: 4900 mm Machine width: 1400 mm Machine height: 1850 mm Spray weight: 5300 kg

Arburg 470C 1300-350 with 40mm plasticising unit. The ‘C’ variant of machines from Arburg is one of our most popular requests (once refurbished). These machines were market leaders for quite some time and proved reliable and good value for money over the years. With a little refurbished magic from the team to bring them back to ‘almost new’, these machines now have a new lease of life. They might not be the most energy efficient, but they are by no means power hungry and when the low upfront cost is considered with low maintenance costs, it’s a very good value option. Refurbished machines from STV Machinery undergo a comprehensive test procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. Machines are ultra clean and ...

Now fully refurbished and in our stock in Wellingborough, Northamptonshire is this tie-bar-less Engel Victory 330/90 Tech injection moulding machine. Fitted with a 35mm plasticising unit which gives a maximum shot weight of 134 (PS) (g). This is a high specification machine with double core pull, CC100 controller, singe pneumatic core pull and 8 zone hot runner controller built in. It comes complete with system disks to suit the machine. The unique design of these machines allows for large tools to be installed with ease and often much larger than could go in comparable 90T machines with tie-bars. A very versatile machine with proven technology and good support from the people at Engel UK. This machine is now holding maximum lock, has no detectable wear in the plasticising unit and is cosmetically excellent. You can find out more about the work we’ve done to this specific machine ...

Now fully refurbished is this four tie-bar BOY 30 tonne clamp machine with Dipronic controller . The Dipronic controller fitted to this machine and other ‘D’ series has stood the test of time and is now even demanding a premium. The controller and setup of the machine is straightforward, easy to problem solve and great for learning. Without expensive computer controlled systems, the cost of any repairs are often very low and easily carried out. The machine offers excellent platen dimensions and tie-bar clearance for the footprint, these machines are some of the most popular in the market for their niche. Refurbished machines from STV Machinery undergo a comprehensive test procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. M ...

Our team are currently working on this 2008, BOY 90M injection moulding machine. It comes fitted with the Procan MD controller, 48mm plasticising unit with bi-metallic barrel and single core pull and two 16A sockets. It has only 35,000 recorded run hours. BOY 90 machines are some of the smallest (footprint) machines around for their clamp size. The design of the clamp unit on these machines means easy access for tool mounting and clear space below the clamp unit for conveyors etc. Very popular machines on the used market and support are readily available from various sources across Europe as there are a lot of these machines in operation. Come down and have a look yourself. Refurbished machines from STV Machinery undergo a comprehensive refurbishment procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fau ...

KRAUSS MAFFEI KM 110-520 C1 injection moulding machine was built in Germany in 2003. The machine used in production plants produces top-quality plastic products using the injection moulding method, which involves feeding a plastic material of sufficient plasticity into an injection mould, which is then clamped with a high force of 110 tonnes. To ensure the highest possible operating efficiency and productivity, the machine uses reliable components, such as a powerful screw with a diameter of 45 mm and an ejector with a force of 22 kN. The KRAUSS MAFFEI KM 110/520 C1 injection moulding machine weights 6000 kg. Technical data of the KRAUSS MAFFEI KM 110-520 C1 injection moulding machine - mould clamping force: 110 t (1100 kN) - mould opening force: 7 t (70 kN) - injection volume: 275 cm3 - injection capacity: 159 cm3/s - injection pressure: 1878 bar - injection weight: 250 g - p ...

ENGEL INSERT 200H/50 injection moulding machine was manufactured in 2007 in Austria. The machine with its small size and large capabilities is used for e.g. overmoulding of inserts and the joining of various materials such as glass, metal and electronics. Thanks to the combination of a clamping force of 50 tonnes and high-quality components, the injection moulding machine guarantees excellent quality of inserts and high repeatability. The machine’s sturdy, solidly built construction features a convenient and easy-to-use ENGEL CC 200 CNC controller for entering all possible process parameters, such as mould clamping force and speed. Once the parameters have been entered, the two halves of the mould are precisely closed, after which the vertical injection moulding machine ENGEL generates a high clamping force. The mould cavity is carefully filled with plastic under high pressure using ...

WELLTEC TTI 450 FH injection moulding machine was manufactured in 2008 in Hong Kong. The machine of rigid steel construction, is ideal for the mass and unit production of plastic products. Plastic of sufficient plasticity is fed into an injection mould of minimum dimensions (L x W) of 125 x 125 mm, which is then clamped with a high force of up to 450 tonnes. The high clamping force and the reliable components used in the machine ensure that the user receives products of the highest quality and that productivity and efficiency are significantly increased. The WELLTEC 450 T injection moulding machine is also equipped with a CNC controller for the input and editing of all the necessary machining parameters. The total weight of the machine is 17600 kg. Technical data of the plastic injection moulding machine WELLTEC TTI 450 FH - CNC controller - maximum clamping force: 450 t (4500 kN)  ...

WELLTEC TTI 450 FH injection moulding machine built in 2008 in Hong Kong, is distinguished by its high clamping force of up to 450 tonnes and efficient high-end components. The machine designed for plastic processing uses the injection moulding method, which involves feeding plastic of suitable plasticity into an injection mould of minimum dimensions 125 x 125 mm and then clamping it with high force. As a result, high quality products are obtained in a very short time. The WELLTEC injection moulding machine has a steel structure, inside which are installed state-of-the-art components to maximise overall productivity and efficiency, and to ensure reliable operation of the injection moulding machine for many years of use. On the arm there is an operator panel with a convenient and easy-to-use CNC controller, with which the operator can enter and edit all the possible parameters of the p ...

ENGEL ES 330/80 HLS injection moulding machine built in 1998 in Austria is designed for processing plastics by injection moulding. The injection moulding machine is equipped with top-quality components that increase productivity and efficiency. All parameters are conveniently programmed on the ENGEL CNC control installed on the machine body. The plastic processing machine weighs 4900 kg. Technical specifications of the ENGEL ES 330/80 HLS injection moulding machine - CNC controller: ENGEL - clamping force: 80 t (800 kN) - screw diameter: 35 mm - maximum screw speed: 400 rpm - minimum screw speed: 20 rpm - injection pressure: 1600 bar - injection speed: 113 mm/s - minimum mould height: 200 mm - maximum mould opening stroke: 450 mm - mould mounting platen dimensions (L x W): 660 x 560 mm - maximum distance between platens: 650 mm - mould mounting hole dimension (fixed plate) ...

ENGEL ES 200/75 HL-V injection moulding machine was built in Austria in 2000. The highly reliable and robust machine is designed for processing plastics by injection moulding. The high-end components installed on the ENGEL ES 200/75 HL V injection moulding machine guarantee a significant increase in work efficiency and productivity. The machine operating with a force of 75 tonnes works with injection moulds of a minimum height of 200 mm, which are placed on 660 x 560 mm platens. All process parameters are programmed and controlled on the convenient and intuitive ENGEL CNC control, located on the body of the plastics processing machine. The total weight of the machine is 4700 kg. Technical specifications of the ENGEL ES 200/75 HL-V injection moulding machine - CNC control: ENGEL - clamping force: 75 t - injection volume: 135 cm3 - injection pressure: 1065 bar - injection speed: ...

ENGEL INSERT 60H/30 SHUTTLE injection moulding machine was manufactured in 2016 in Austria. A specialised machine with a small footprint, is used for, among others, the overmoulding of inserts and the joining of various materials such as glass, metal and electronics. Thanks to the electric control of the injection unit and the ‘pressure locking’ system for the injection cylinders, the injection moulding machine guarantees high repeatability and excellent quality of inserts. The ENGEL INSERT 30 injection moulding machine allows you to set the speed and clamping force to prevent damage to the mould. Once both mould halves are closed and a high closing force is generated, the injection unit pushes the nozzle against the injection sleeve of the mould and produces an adjustable clamping force. At the end of the cycle, a very powerful screw with a diameter of 18 mm injects the melt unde ...

FERROMATIK MILACRON ELEKTRA 155 injection moulding machine, manufactured in 2003 in Germany, is used in the processing of thermoplastics by injection moulding. The robust steel construction is equipped with first-class components, characterised by high reliability and performance. The FERROMATIK MILACRON EE155 machine works with injection moulds with a height between 200 and 590 mm, which are mounted on 780 x 780 mm platens and closed with a force of up to 155 tonnes. The combination of the high closing force with a 45 mm diameter screw, rotating at 250 rpm, guarantees the best quality of the produced products. The total weight of the injection moulding machine is 7800 kg. Technical parameters of the FERROMATIK MILACRON ELEKTRA 155 injection moulding machine - clamping force: 155 t (1550 kN) - screw diameter: 45 mm - maximum screw speed: 250 rpm - screw stroke: 200 mm - mould ...

PONAR ŻYWIEC UT-090 H injection moulding machine was manufactured in 2001 in Poland. The machine, designed for plastic injection moulding, is equipped with high-end components, increasing productivity and ensuring high reliability. Located on the body of the injection moulding machine, an operator’s panel with an installed MOOG-BUHL CNC controller allows for complete automation of the injection process and control of parameters. Moulds with a minimum height of 225 mm, mounted on 615 x 615 mm platens, are closed with a force of 90 tonnes by a hydraulic clamping unit protected by fixed and movable guards. The combination of the high clamping force of the mould, together with a powerful screw with a diameter of 30 mm, guarantees the best quality of the manufactured products. The extensive equipment offered with the UT 090 H injection moulding machine includes a pneumatic plastic feede ...

ENGEL ES 330/80 HL injection moulding machine was built in Austria in 1995. A highly reliable and efficient machine equipped with high-end components, is used in the processing of plastics by injection moulding. The combination of high mould clamping force and a powerful screw with a diameter of 35 mm guarantees the high quality of the manufactured products. The injection moulding machine works with injection moulds with a height from 170 to 370 mm, which placed on 710 x 660 mm platens are closed with a force of 80 tonnes. The machine is equipped with an ENGEL CC100 CNC controller for setting injection moulding process parameters, an ENGEL ERC 23/1-CH servo-driven multi-axis robot and a pneumatic and hydraulic core. The tie-bar-less injection moulding machine weighs 5300 kg. Technical specifications for the ENGEL ES 330/80 HL injection moulding machine - maximum clamping force: 80 ...

FERROMATIK MILACRON EUROPE ELEKTRA 300 injection moulding machine was built in Germany in 2000. The machine produces high-quality plastic products using the injection moulding method. The plastic is fed into plate-mounted injection moulds with a height of 200 to 670 mm, and then welded with a force of 300 tonnes to produce items with the right shape and properties. The FERROMATIK MILACRON E300-S injection moulding machine is equipped with, among others, a large screw with a diameter of 60 mm and an operator panel located on the body of the machine with a FERROMATIK MILACRON IQT 33 CNC controller installed, allowing full control of all process parameters and programming of operating modes. The total weight of the FERROMATIK MILACRON ELEKTRA 300 S injection moulding machine is 17460 kg. Technical parameters of the FERROMATIK MILACRON EUROPE ELEKTRA 300 injection moulding machine - c ...

ELWIK RT-C hot runner control system is a device for ensuring the right temperature during the injection process. The mould temperature controller, built in a panel system, adjusts temperature in the range from 0 to 500°C using a coding switch. The advanced technology and safety features included in the device guarantee uninterrupted and reliable operation of the mould temperature controller. The P, PI, PID parameters are set automatically by the temperature controller to the injection moulding machine, thanks to an auto-adaptation function that ensures that the pre-set temperature is not exceeded. The heater is dried when the supply voltage is reduced, completely protecting it from burning out. The mould temperature controller is equipped with six heating zones with a 16 A load per zone, making it possible to process any type of plastic. Technical specifications of the ELWIK RT-C ...