used LIND for sale

Built in 2019 immediately available Special price limited in time! No return of the used battery required! Price is valid without returning the used battery! Manufacturer Hawker (formerly VHB and Varta) Country of manufacture: Germany Place of production: Hagen Voltage 80 volts Ampere hours 930AH Connection cable Rema 320A Description: Forklift battery, traction battery for forklift 80 volts 930 ampere e.g. Still R60-40, Still R60-45 and others like Linde, Clark, Jungheinrich, Kalmar, Dosan, Omespo, BT, Wagner and many more Type N 80V 6PZS930 Trough mass LxWxH 1.025mmx996mmx767mm Weight 2.196kg New, unused and OVP, ready to ship! Special price

Forklift, forklift reworked! Manufacturer Hyster Type H4.00XL6 Lifting capacity 4to Drive propellant gas Engine 6 cylinder V-engine Operating hours approx. 5,500 hours Twin tyres 4 valves up to the mast for side sliders, and hydraulic fork tine adjustment or bale clamp with pressure control valve Lifting height, depending on the mast, either 5m, or 6m then Construction height either 3.4m or 3.9m Weight approx. 7to. Forklifts were technically overhauled, the brakes, the load chains, the water pump and the sedparts were renewed. The mast was completely disassembled, cleaned, re-laced. All worn parts have been renewed. New UVV possible on request! Geraet is in very good condition. H 4.00 XL 6 Special price Hyster Linde Kalmar Hubtex Still Wagner Jungheinrich Etwo

Forks Forks for forklifts Manufacturer Linde Type FEM4B Load capacity (pair) 10to Length 2.000mm Width 200mm Thickness approx. 70mm

10 stupid pneumatic cylinder double acting RT/57216/M/50 Diameter 16mm Piston path 50mm p 1-10bar Tmax 80C L2H (new price per piece 31.52.-EUR) Additional ly20 piece Norgren Reed Switch M/50/LSU/2V Lock (NP24.95/pc) Additional items Screw fittings and connections Additional mounting kit QM/33/016/23 Pneumatics, hydraulics, drive elements Special price

Electric forklift Manufacturer Linde Type E20 Built in 2000 Duplex mast with full-free stroke Side slider Tine adjustment Few operating hours Very good condition New unused battery, Hawker 80 Volt

hardly used diesel high-pressure compressor from Bundewehr bestaenden. Drive via Ferryman 1 cylinder diesel engine Printing power 28bar Fuel quantity 200 litres /min Geraet is completely autarg. Motor is started by means of a hand crank. Base mass 1200mmx700mm Weight 380kg Special price Kaeser Boge Schneider Hydrovane Atlas Copco Ingersoll Rand Deutz Perkins Volvo Liebherr Hatz

Unused charging equipment for electric forklifts 48 Volt 120 A Processor-controlled BAE Duo loader with electrolytum woe Price on request More used loaders 24Volt, 48Volt, 80Volt of 55 amperes up to 200 amperes at the camp, please ask. Special price Varta Hawker Migatronik Still Linde Wagner

Soundproof Diesel Generator Set Emergency Generator Set Manufacturer: Lucla Type GLU-33-SK Specifications Continuous power: 30 kVA Standby power: 33 kVA Mains voltage: 400/230 V Amperage: 43.3 A Max. sound level: dB(7m) =78 Engine: KOFO Model: K4100D Intake system: naturally aspirated engine Fuel Injection System: Eddy Number of cylinders: 4 Displacement: 3,613 L Bore x stroke: 100x115 mm Compression Ratio: 20:1 Nominal speed: 1500 r/min Engine power: 33 kW Controller: Mechanical Starting voltage: 12 V Generator: Lucla Model: LU 184GS Phase: 3 Voltage: 400 V / 230V 43.3A Line type: 3 phase 12 cable, Y type Stock: 1 Power factor (cos f): 0.8 Frequency: 50 Hz Continuous power: 30 kVA / 24KW Arousal Type: Brushless, Self-Arousal Voltage Regulation: % ±0.5 Protection class: IP 23 Degree of insulation: H Altitude(above sea level): m =1000 Controller: ...

Built in 2019, immediately available! No return of the used battery required! Special price limited in time! No return of the used battery required! Glvaxkt Forklift battery, traction battery for forklift 80 volts 500 amperes e.g. Linde E20-02 and others like Still , Clark, Jungheinrich and many more Type N 80V 4PZS500 Cable 50mm2 Length 1,400mm Plug Rema 160A Trough mass LxWxH 1.025mmx705mmx610mm Weight 1.211kg New and unused! Special price

1 Hubgeruest from the Still R70-45 forklift truck without free stroke Lifting capacity 4,500kg with side slider and fork tine adjustment incl. hydraulic slurs Building height 280cm, weight approx. 800kg Price 2,400.-EUR 2. Lifting truck from the Linde E15 forklift Lifting capacity 1500kg Building height approx. 220cm with side slider Price 450.-EUR 3. Duplexhugeruest Hyster XL4.00 without free stroke Lifting capacity 4000kg Building height approx. 400cm with fork-traeger Price 2,650.-EUR Forklift Hubger Mast Mast Forklift Truck Hyster Linde Kalmar Still H80D R60-45 R70-45 E15 E20 DCD90-6 DCD 100-6 DCD 120-6 Special price

Vice Heuer Front with height adjuster Type 160 Jaw width 160mm Adjustable in height via column with gas pressure cylinder. Special price

Praezision tube Residual bestaend from the production of gas pressure cylinders Stainless steel, probably V2A or V4A Laenge each 6m The following dimensions should be available, exact quantities on request or on order. 3x20 7x23 4x28 1x40 Sale against bid either as a total length or by length or by meter Special price

Hydraulic C-frame press Tool testing press / straightening press Pressure power hydraulic unit approx. 400kg/cm2 Printing capacity of the press approx. 270to Partially overhauled! Hydraulic cylinder sour overhauled, recoat Table clamping area 1.300x500mm Flat of the printing plate 700x400mm Number of T-slots 2 pcs with width 22mm Piston rod diameter 290mm maximum installation height 750mm Piston path 350mm Extension C-frame to center piston 270mm Extension C-frame to front edge pressure plate 480mm Width C-frame 500mm Aeussere Dimensions Depth 1,800mm Width 1,300mm Rxvukelzy Height approx. 3,000mm Weight approx. 5to Rest according to photos Special price

Two hydraulic valves from Rexroth, two hydraulic pumps and 5 hydraulic cylinders are offered, all new and indispensable as spare parts 1. 2 Stueck Rexroth Valves MNR: R900912485 DBW 10 B2-52/315-6EW230N9K4 FD: 48121 2. Voac Parker Hydraulics made in Sweden Part No. 3708719 Type F11-058-M8-CF-K-000 Ser No. 2000180541 3. Brueninghaus Hydromatik D-72160 Horb A10VSO 71 DR / 31R PPA12N00 FabrNr: 1117486 Bauj. 04/96 DR = 280 bar Vo =71 cm3 n=1500 min 4. 5 unused, two-sided hydraulic cylinders with bearings Type 70/50-280-625 Length from middle hole to middle hole approx. 625mm Total length approx. 750mm Piston diameter 70mm Rod diameter 50mm Piston path 280mm Special price

Pneumatic double piston dosing pump for pumping and mixing 2 media. 1 pneumatic cylinder with 2 pump heads. Required air pressure 8 bar. 1/2-inch connections with 4 stopcocks. Up to approx. 40 strokes per minute, or approx. 80 litres per minute / approx. 5 cbm per hour. On platform wagon ant with 2 swivel/brake castors and 2 fixed castors. Overall pump dimension: 6001300x1000mm, weight about 80kg.

TECHNICAL DATA SHEET CNC – Gantry gantry milling machine TRIMILL brand Type VF3016 Year of construction 2017 Control HEIDENHAIN iTNC530 HSCI Travel X-axis (longitudinal): 3,000 mm Y-axis (transverse): 1,600 mm Z-axis (vertical): 1,200 mm B-axis (swivel axis milling head) +/- 100 ° C-axis (rotation axis milling head) +/- 240 ° Structure / Axis concept AC servomotors with digital control for all axes Gantry drive of the X-axis Rack and pinion drive in the X-axis, backlash-free due to electrically prestressed, water-cooled motors 2 ball screws each in the Y and Z axes Guides of all linear axes are designed as prestressed roller guides Hydro-pneumatic weight compensation of the Z-axis via 2 cylinders Stationary frame components made of mineral casting, movable main components made of grey or nodular cast iron Double beams in load- and thermosymmetric d ...

Double Column Machining Center TOSHIBA MPC-3180B Table mm.8000 x 2700 Distance between columns mm.3100 X mm.9000 Y mm.3900 Z Verticaal RAM stroke mm.900 W Vertical Crossrail stroke mm.1600 Automatic indexed every 5 degrees 5 face head Distance table to spindle nose mm.2440 Table load Kg. 20.000 Spindle speed 5-3000 rpm 2 ranges Spindle taper BT 50 Ram section 380 x 380 Machine dimensions mm.29110 x 9900 x 7260 Machine weight Kg. 151.000 Year 2007 Standard options : 5-face cutter head Automatic attachment (5-face cutter head or other attachments)index (AAI) (4-position index by 90.) Automatic tool loading/unloading device for vertical spindle and horizontal spindle) CNC controller including standard and pack specifications Pendant operation box with electrically-driven free arm Hydraulic unit Oil cooling unit (AKZ 908) Hydraulic crossrail servo balancing s ...

Studer S33 CNC Universal Cylindrical Grinder New 2018 CNC Control: yes Type of CNC Control: Fanuc Oi-TD Capabilities and Features: 350mm x 1000mm OD Grinding Wheel Dimensions: 500 x 63 x 203,2 mm X-Axis Travel: 285 mm Z-Axis Travel: 1000 mm Resolutiion: 0,0001 mm Max. work piece weight between centers: 80 kg Swivel Table: -15 - +225 ° Indexing: B axis Automatic 1° Hirth Coupling Grinding wheel size: 500 x 63 x 203,2 mm Peripheral speed max.: 50 m/sec Motor power capacity: 14.47HP / 11kW Work piece spindle head: See Specs Below: See Specs Below Number of revolutions: 1 - 1.500 rpm Workhead Motor Power capacity: 1,6 / 3 kW Spindle passage: 30 mm Fitting taper: MK 5 Center Height: 175 mm Workload: 80 kg Machine-Datasheet - Overall: SEE BELOW C-Axis: 0,0001 ° Tailstock: yes Tailstock: - Taper Center Size: MK 4 Travel:: See Below X-Axis ...

WALDRICH SEIGEN WST IV H80 X 12000 ROLL GRINDER YEAR: 1981 / INSTALLED 1982 MAXIMUM GRINDING DIAMETER: 78” ( 1981.2 mm) WITH 32” (812.8 mm) DIAMETER WHEEL MAX DIAMETER CAPABILITY: 2500mm DISTANCE BETWEEN CENTERS: 472.40” (12000mm) MAXIMUM WORKPIECE WEIGHT: 176000 lbs. (80t) WHEEL OD MAXIMUM: 32.00” WHEEL WIDTH MAXIMUM: 4.00” WHEEL ID: 12.00” WHEEL SPINDLE POWER: 27 - 59/59 HP WHEEL DRESSER: BED MOUNTED ROLL WHEELHEAD TRAVEL: 25.60” TABLE TRAVEL: (WHEEL HEAD TRAVEL) 488.40”( 12405 mm) TABLE SPEED: (WHEELHEAD SPEED) 157.5 in/min (4000 mm/min) WHEEL SPINDLE SPEED: 450 - 1800 RPM Infinitely Variable WORKHEAD POWER: 1.9 - 59/59 HP WORKHEAD SPEED: .5 - 300 RPM WAYS: CAST IRON FULL HYDROSTATIC SLUDGE CONVEYOR: NONE COOLANT: YES FILTRATION SYSTEM: COMBINATION 2 CARTRIDGE AND FABRIC FILTER WAY COVERS: METAL TELESCOPIC POWER 3PHASE / 50-60 Hz / 200 - 50 ...

WALDRICH SIEGEN HFB-200 CNC Horizontal Boring & Mill MC Built 1978 / 2007 X=15.000, Y=5.000, Z=1.500, W=1.200mm Spindle diam. 200mm ISO 50+60, 90kW SIEMENS 840 D ATC 90 Table 5.200x5.200mm, X travel 3.300mm max. loading 100 Ton Rotation 360.000° Floorplates 6.000 x 10.000mm Hydrostatic Many heads This machine was used in final cutting and boring, drilling of big vessel engine cylinder blocks in STX Engine. It can be done the straight and inclined direction drilling &boring. It means the spindle head can be tilted. It is very high accuracy machine. This machine is in assembled condition but not under power

Maker: SUMITOMO HEAVY INDUSTRIES (made in Japan) Model: FPA-3000 Year: 1985 (2) Capacity & main specification 1) Capacity: 3000tf 2) Ability Limit Point: 5mm 3) Allowable eccentric load: 3000tf 4) Allowable eccentric distance: L&R 350mm 5) Slide stroke: 350mm 6) Slide stroke speed: 20~50spm 7) Stroke number: 20tpm(Max) 8) Shut height: 1200mm 9) Slide adjust distance: 10mm 10) Bed hard plate dimensions: RL 1300mm x FB 1500mm 11) Slide dimensions: RL 1200mm x FB 1400mm 12) Slide knockout capacity: Total 20tf (pin number: 4ea) 13) SKO stroke: 50mm ( adjust up) 40mm ( adjust down) 14) Bottom knockout capacity: 50tf (pin number 4ea) 15) BKO stroke: 20~30mm 16) Upright internal dimensions: RL 1400mm 17) Main motor: DC 200kw x 1450rpm 440V 18) Floor height: 6800mm 19) Working height: 1030mm 20) Side opening: FB 1000mm x TB 1400mm 21) Flywheel energy: 200tf-m (50spm)  ...

Naxos CNC Multi-Axis Cylindrical Grinder Year: 1987/2013 Max. swing: 630mm Max. distance workhead face to tailstock face: 4850mm Max. travel for Z axis: 5000mm Max. grinding distance for main wheel: 4520mm X axis infeed travel for both headstocks: 720mm Approx. weight between centers: 4000kg Power requirements: 460/3/60 This machine was completely remanufactured to new specifications in 2013 and installed in 2014. It was stripped down to the bare casting, table/base/wheel heads/work head and tailstock and the second z axis ways were fit and rescrapped. New electrical cabinet with all new wiring to the machine and new all components, hydraulic lines, air lines and new cable carriers were added. New Marathon 60HP motors for both grinding wheel heads. (The drives in the cabinet are set for 40 Hp) The spindle drives in the cabinet are Yakawa built in the USA along with the workh ...

FEATURES: GIDDINGS & LEWIS 8000 CNC CONTROL, RETROFITTED 2000 55.12" DIAMETER FACE PLATE CHUCK WITH JAWS 16.92" DIAMETER BORING BAR BORING HEADS (2) W-AXIS POSITIONING X-AXIS TAPER FEED PRESSURE MEASURING DEVISE HARDENED & GROUND WAYS COOLANT SYSTEM WITH POLO PAPER FILTRATION PRAB CHIP CONVEYOR SYSTEM CAPACITY: MAXIMUM SWING OVER BEDWAYS 62.99" BORING DIAMETER SOLID BORING 12.4" TREPANNING 2" TO 25" COUNTER BORING WITH PILOT PRE-BORE + 25" MAXIMUM BORING DEPTH, Z-AXIS 396" LENGTH OF BED 1,176" WIDTH OF BED 39.37" MACHINE WEIGHT 180,000 LBS WORK HEADSTOCK: SPEEDS, INFINITELY VARIABLE 1.8-355 RPM SPEED RANGES 4 MAIN SPINDLE DIAMETER FRONT BEARING 11.81" MAIN SPINDLE BORE 6.4" MAXIMUM TORQUE, 31 RPM AT 180 HP 39,900 FT/LBS MAXIMUM WORKPIECE WEIGHT (1) REST 88,000 LBS MAXIMUM WORKPIECE WEIGHT (2) RESTS 110,000 LBS MAXIMUM WORKPIECE WEIGHT (3) RESTS  ...

Takang TKV-860-HT CNC Twin Spindle Vertical Turning Center Year 2015 . GENERAL SPECIFICATIONS Max. Cutting Diameter: 800 to 1000mm Max. Swing Diameter: 1000mm Max. Cutting Length: 860mm Spindle Motor (FANUC aP40): (2) 50 HP Alpha P40 2-Speed Gearbox Motors Spindle Speed Range: 10-1500 RPM Spindle Nose: A2-11 Spindle: Spindle Motor (FANUC aP40): (2) 50hp Alpha P40 2-Speed Gearbox Motors Spindle Speed Range: 10 - 1,500rpm Max Chuck Diameter: Installed 31.5" 3- Jaw Hydraulic Chucks Spindle Nose: A2-11 Front Bearing Diameter: 7.87" Spindle Bearings: Double Row Cylindrical and Angular Contact Spindle Speed Selection: Direct RPM Programming Spindle Speed Override: 50% ~ 200% Speed Range Shift: 2- Speed Gearbox Programmable High-Low Range Axis Drives: X Axis Travel (FANUC a22/3000i AC 4.0 HP): 18.31" Z Axis Travel (FANUC a22/3000iB AC 5.0 HP): 33.07" X Axis Thrust Force: ...

1. General specification -Maker MES (Mitsui Engineering & Shipbuilding Co., Ltd.) Japan -Mfg. data 2014 -Running time Zero hoursP 2. Steam turbine specification -Maker MES (Mitsui Engineering & Shipbuilding Co., Ltd.) Japan -Turbine type CD30.46 -Steam in let pressure 70barG -Steam inlet temperature 490℃ -No.1 Extraction steam P & T 31.5barG & 388.5℃ -No.2 Extraction steam P & T 5.5barG & 223.3℃ -Nor. Exhaust pressure 0.11barA -Turbine speed 3,600 rpm -Rated output 97,500 kw -Weight 132 ton -Number of stages 16 -Number of 1 stage nozzle arcs 4 -Steam inlet flange ASME1500#RJ12” x 2 -No.1 extraction steam flange ASME 600#RF 16” -No.2 extraction steam flange ASME 150#RF 32” -Steam exhaust flange ø3,600(inner dia.) 3. Synchronous generator -Standard IE60034-1(2010), IEC60034-3(2007) -Location Indoor -Cooling system Totally enclosed type with top-moun ...

Inv. Num. : 7292 Type: FS30 Producer: LINDNER Created: GO 1999 Parameters: Machine weight: 3900 kg The grinder is in good condition.

Inv. Num. : 7293 Type: FS30 Producer: LINDNER Generated: Parameters: The grinder is in good condition.

Inv. Num. : 7459 Type: GU-A Producer: LINDNER Generated: Parameters: The mill is in good condition.

Inv. Num. : 6978 Type: P4-2220 Producer: Salvagnini Created: 2003 Parameters: Switch-on hours: 66,600 h Compressive force: 220 t Maximum bending length: 2250 mm Max. bending height: 203 mm Maximum sheet thickness (mild steel): 2 mm Maximum sheet thickness (stainless steel): 1.2 mm Maximum sheet thickness (aluminum): 3 mm Equipment: Tools 2023 New hydraulic motor on ADP New valves on ADP New temperature sensor ADP Customization RIP Customization Adjusting the stop on the X and Z axes 2020 Replacement of the lower bending knife on P4 2220 Pressure test and replacement of 3 x oscillating cylinders Pressure test Upper bending of oscillating cylinders Regulation of the upper bending blade Adjustment of the lower bending blade Replacement of the cables on the left side of the valves and on the right side 3A1-AH 6 2019 Rotator Adjustment Replace ...

Inv. Num. : 6762 Type: WHN 9 B Producer: TOS Created: 1975 Parameters: Repair history: 30.8.2021: Repair of the rotary table 31.5.2021: Repair of the lubrication system for guide surfaces 18.02.2021: Adjustment of the rotary table coupling 22.10.2020: Replacement of the sealing elements of the hydraulic cylinder of the tool clamping Replacement of the tool support bearings Replacement of hydraulic hoses for tool clamping 21.10.2019: Replacement of the electromagnetic clutch 09.10.2019: Brush holder - carbon 31.1.2017: adapted quick-shift clutches with replaced spark plugs and shift knobs on the "Y" axle 11.03.2017: Lockshift clutch

Inv. Num. : 5464 Type: 1250x1.2 Producer: China Created: 2014 Parameters: Maximum sheet thickness when cutting: 1.2 mm Maximum length of sheet plate: 1250 mm Equipment: 7-cylinder sheet metal straightening machine 2 knives for longitudinal cutting Unwinding and rewinding of sheet metal

Inv. Num. : 6260 Type: RZ-01 Producer: KOMFI Generated: 2001 Parameters: Equipment: Lower Replacement Pressure Roller Replaceable chrome screen cylinder (small worm pattern) Paper anilox roller (pattern coarse canvas)

Inv. Num. : 6409 Type: KDC-N24 R2T Producer: KISUN Generated: 2018 Parameters: Electrical connection: 240 V Power consumption: 21 kW Compressed air: 6 bar Length: 6120 mm Width: 1070 mm Height: 1370 mm Equipment: Loader Termo Air Dryer Uv Spare screen cylinder and doctor blade chamber Discharger format: 610 x 750 mm (B2) Minimum. Size: 297 x 420 mm (A3) Paint layer height: 6-14 microns Painted material thickness: 120-400 g/m2

WEINIG / GreCon Short Wood Finger-jointing Line Ultra TT Data of the system: • Wood inlet length (min. - max.) 150 - 1000 mm (1300 mm) • Reference timber inlet length at the finger-jointing line 400 mm • The length of the wood to be processed must be at least 25 percent longer than the width of the wood to be processed • Wood thickness (min. - max.) 20 - 80 mm • Reference wood thickness 28 mm • Wood width (min. - max.) 40 - 205 mm • Reference wood width 90 mm • Reference wood cross-section 28 mm x 90 mm • Wood outlet length (min. - max.) 3000 - 6100 mm • Reference wood outlet length 6100 mm • Tine profile (length) 10 – 11 mm • Max. wood cross-section for processing softwoods (with specified tine length) 100 cm² • Max. wood cross-section for processing hardwoods (with specified tine length) 80 cm² • Glue type PVAC • Species: Softwood / ...

PROBAT UW 801 MILL IN GOOD WORKING ORDER - SOLD WITH A PAIR OF SPARE CYLINDERS - WITHOUT ELECTRICAL CABINET - THE INSTALLED CYLINDERS ARE IN VERY GOOD CONDITION - CAPACITY: +/- 1000 K / H - PROVIDED FOR WATER COOLING (TO BE RENOVATED). IMMEDIATELY AVAILABLE

SERAPID 12 T die cart built in Germany is an innovative vehicle of stable design, able to maximise production processes through the precise, safe and efficient lifting of dies or tools. All of this is due to an extremely efficient electric drive, reliable cylinders and rigid chain technology, which is an environmentally friendly alternative to traditional hydraulic systems. The SERAPID 12 tonnes die change cart also guarantees increased reach at maximum working speed, thanks to the capacious Hawker Perfect Plus batteries. The net weight of the machine is 5200 kg. Technical specifications of the SERAPID 12 T die lifting cart - maximum load capacity: 12000 kg - maximum lifting height: 2000 mm - minimum lifting height: 740 mm - lifting speed: 0-57 mm/s - travel speed: 2.7 km/h - chain stroke: 2500 mm - batteries: Hawker Perfect Plus - battery capacity: 48 V – 330 Ah - chain ty ...

METRIS-NIKON MCA II 5124 measuring machine built in 2011 is a versatile device that can be used for measuring both small-sized objects as well as complex, large-sized parts. In addition, thanks to the computerisation of measurement procedures and its compact design, the machine can be used directly in the production environment or even inside the measured objects. The measurement process starts with an angular displacement of the arms to ‘pass’ through reference points. The operator then brings the machine’s measuring tip to the surface of the measured workpiece and validates the coordinates using a button located on the head. The coordinates are then transformed by the calculation procedures to the cartesian system (X,Y,Z), where they are used as the basis for determining the dimensions by approximation of the measured features and geometric figures, i.e. circles, cylinders and ...

DURMA SB 3020 hydraulic guillotine shears built in 2008 in Turkey are an ideal choice for machining stainless steel, copper, aluminium and plain steel. Workpieces with a maximum thickness of 20 mm are cut using extremely precise, hardened cutting knives with manual adjustment of the gap between the blades. The high-quality monoblock design, combined with the hydraulic system, additionally ensures the highest stability and machining performance, even during the most demanding challenges. To facilitate the operator’s work, special transport rollers have been integrated into the work table, on which the workpiece is fed directly under the cutting line. The machining parameters are programmed in the intuitive DURMA ENC 100M control panel with clear LCD display and memory for 50 programs. The DURMA SB 3020 guillotine shears also features a driven back stop with T-slots and sockets with d ...

GWELL GWC 80-156 WPC production line manufactured in 2015 is characterised by high production efficiency. WPC boards are made by combining natural components with thermoplastic polymers. This results in a material with the high aesthetics of wood and the exceptional durability of plastics, distinguished by full resistance to fungus, insects and various atmospheric factors. The production line consists of: – GWC 80/156 twin-screw extruder – GWC 65/132 twin-screw extruder – CUT 240 saw – CAL 14000/6 calibrating table – ROL 240 2-caterpillar haul-off – unloading table The WPC profile extrusion line is offered with optional heads for forming different types of profiles from these products. To date, the machine has only been in operation for a dozen days and has not been used at full production scale. For an additional charge, equipment cooperating with the line can ...

ALUWIL ST 3000 roller blind cutting table built in Poland in 2019 (implemented in production in 2022) offers the best combination of speed and precision in cutting thick materials. The fabrics arranged on a large working area are machined by an under-top mounted cutting blade with forward and reverse feed control via ALLEN-BRADLEY touchscreen HMI panel. Once the cut is complete, the knife automatically returns to its initial setting, followed by the release of the bilateral pneumatic hold-downs that hold the fabric. The ALUWIL ST-3000 fabric cutting table is also distinguished by its highly rigid steel-aluminium construction and extensive equipment, including a feed bar, fabric end detection sensor and measuring stop. The ALUWIL cutting table weighs 380 kg. Technical data of the ALUWIL ST 3000 fabric cutting machine - work area (L x W): 2800 x 2850 mm - circular cutting blade - fab ...

ZEMAT PULSA ECO 500 impulse welding machine was built in 2019 in Poland. The compact machine with an open design is ideal for the efficient production of canopies, awnings, pergolas, roller blinds, banners, etc. The individual temperature control of the upper and lower sealing electrodes together with InvisiWELD technology produces strong, practically invisible seams with high precision. Furthermore, the operator has special hand tools at his disposal for the welding of, e.g. tabs, pockets and zippers. The ZEMAT PULSA EC semi-automatic impulse welder was implemented in production in 2023 and since then has been used for only a dozen tests. The total weight of the machine is 1800 kg. Technical specifications of the ZEMAT PULSA ECO 500 welding machine - machinable materials: PVC, vinyl, polyurethane (PU), polypropylene (PP), polyethylene (PE), rubber, acrylic, thermoplastic materials  ...

SUTEAU ANVER XPM 18X13 300T receding head die cutting press was built in France in 2008. The machine aimed at mass production, is used in the process of precise cutting in foam and non-metallic materials, such as plastics, textiles and rubber. Built-in hydraulic systems combined with a stable design and reliable components ensure high precision and speed of cutting, regardless of machined material. The material taken from rolls or sheets is pressed against the machine head by the vertical movement of the working table, under which hydraulic cylinders are located. The cylinders exert a balanced pressure to achieve the ideal position of the table in relation to the head. The material is then machined using dies that can be mounted either to the head surface or on a lifted table. To facilitate the operator’s die positioning and the insertion and removal of the cut material, the SUTE ...

MADORA SB 1300X2500 aluminium grinding machine was built in 2018 in Poland. A highly reliable machine designed for a wide range of finishing operations i.e. deburring and edge rounding, achieves excellent machining results on the entire surface of the ground workpiece. For surface finishing of workpieces with a maximum thickness of 50 mm, the machine uses a 1300 mm wide technical fleece cylindrical grinding wheel with adjustable oscillation. The SB 1300X2500 aluminium sheet grinding machine is operated via a TFT control panel, which allows, among others, to adjust the machining thickness and change the feed speed of the gantry. The total weight of the machine is 2870 kg. Technical data of the MADORA SB 1300X2500 deburring machine - work table surface (L x W): 2500 x 1300 mm - maximum workpiece thickness: 50 mm - minimum workpiece thickness: 0.5 mm - feed rate: 0,5-2 m/min - numbe ...

DURMA IW 55/110 BTD ironworker machine manufactured in 2014 in Turkey helps to significantly increase production efficiency while keeping operating costs low. The highly versatile and multifunctional machine has a rigid and stable frame made of steel plates with 5 work stations for precise hole and corner punching, as well as cutting flat bars, angle bars and solid bars. The DURMA hydraulic ironworker machine guarantee excellent cutting quality throughout their service life, thanks to the use of a hydraulic cylinder with a centrally located actuator. The total weight of the machine is 1660 kg. Technical specifications of the DURMA IW 55/110 BTD ironworker machine General data - punching force: 55 t - cutting force: 110 t - number of workstations: 5 - number of hydraulic cylinders: 2 - cylinder stroke: 50-60 mm - number of cylinder strokes (20 mm stroke): 37/min - reach: 510 mm ...

AGIE AGIECUT EXCELLENCE 2 wire EDM machine built in 1999 in Switzerland, is used in the production of e.g. precision dies, tools and punches. For the machining of workpieces, the machine uses advanced electrical erosion technology which makes it possible to achieve difficult shapes in even the hardest materials. The use of this method further minimises or completely eliminates the need for other secondary processes, such as polishing. The AGIE EDM machine is equipped with a state-of-the-art AGIEVISION CNC controller and brushless axis servo motors to guarantee the highest machining accuracy and precision in the shortest possible time, with low energy consumption at the same time. The machine also comes with among others an integrated generator, a semi-automatic wire threading system and the AGIESETUP 3D measuring probe for automatic detection of the plane and position of the workpiece ...

RAFAMET KCI 320/400N CNC vertical turret lathe manufactured in 2011 in Poland, can perform complex production programmes on large-size workpieces, thanks to one turning head and three milling heads set at different angles. The machine, with its compact frame structure made of high-quality grey cast iron, is distinguished by its high geometric stability, high rigidity and excellent vibration damping. The CNC vertical turret lathe KCI 320/400N performs precision turning, milling, drilling and boring of cylindrical, conical and curved surfaces with the aid of the applied heads. One of them is a special milling head (offset), used to perform drilling and milling operations with the position of the tool axis offset from the spindle axis in a direction parallel to the slide travel plane. On the other hand, the turning head allows to mount CAPTO turning tools in horizontal and vertical socke ...

MACRI ITALIA PROVAR 5-90 U-D tube bending machine, built in Italy in 2010 is used for the fully automatic process of fixed radius and variable radius workpiece bending on two different dies. The machine is characterised by a highly rigid steel structure, modern components and extensive equipment. All 5 axes of the machine (X, Y, Z, B1, B2) are equipped with reliable brushless servomotors in order to provide the user with high dynamics and excellent positioning accuracy when machining tubes and profiles with a maximum length of 5100 mm. The installed state-of-the-art MACRI software allows, among others, to program the positioner force, perform an anti-collision test with 3D simulation, import files from 3D programmes and program the speed of movement of each axis for each bend. The PROVAR 5-90 U-D mandrel bending machine weighs 6000 kg. Technical specifications of the MACRI ITALIA PROV ...

GEKA BENDICROP 60 SD ironworker machine was manufactured in 2016 in Spain. Equipped with 5 work stations, the ironworker machine performs precise hole punching, corner cutting, flat bar cutting, as well as bar cutting and bending. The vertical movement of the shears is performed by two adjustable hydraulic cylinders with a central positioned actuator, which guarantees excellent cutting quality throughout the entire life of the machine. The GEKA ironworker machine weights 1750 kg. Technical specifications of the GEKA BENDICROP 60 SD hydraulic ironworker machine General data - maximum press force: 60 t - number of cylinder strokes: 32/min - dimensions (L x W x H): 2010 x 1400 x 2006 mm - weight of machine BENDICROP 60 SD: 1750 kg Hole punching station - maximum bore size (diameter x thickness): ø 40 x 11 mm - throat depth: 500 mm - additional table for hole punching fi 100 ...

STROJARNE PIESOK XZMP 3150/6.3C 3-roll plate rolling machine built in Czechoslovakia in 1983 is designed for pre-bending and rolling sheet metal into cylindrical or conical covers and segments. The machine is distinguished by a fully welded structure with increased rigidity and three high-quality 300 mm diameter rollers with longitudinal grooves for easy alignment of the sheet. The bottom rollers, driven by a high-performance motor with two stages of rotation, allow for vertical repositioning during pre-bending and coiling, and also allow for an offset to an inclined position when the claw couplings are opened. As a result, each of the four lower roll bearings can be freely adjusted in the pitch range. The XZMP plate rolling machine has a control panel with a function to monitor the position of the lower rollers directly on the numerical indicators. The total weight of the STROJARNE  ...

HACO TS 3006 hydraulic guillotine shears manufactured in Belgium in 2006, are used in manufacturing plants to cut steel sheets with a maximum length of 3100 mm and a thickness of 6 mm. The machine has vertically aligned knives with four cutting edges, which ensure high precision and quality machining of workpieces regardless of the thickness and type of sheet. The angle of the cutting knives and the gap between them are adjusted by means of two levers at the rear of the machine. During machining, the workpiece is pressed against the cam in order to take an accurate measurement on the gauge located between the front stop and the bottom knife. Two parallel hydraulic cylinders drive the cutting bar (the upper knife attached to the slider) to perform the movement in the up-down direction. The HACO guillotine shears are offered with equipment which includes a foot control, a modern HACO SP ...