used wmw niles facing lathes with tailstock

Tip height: 1250 mm Turning diameter: 2,500 mm over bed Centre distance: 4.000 mm Support motion: 750 mm longitudinal feeds 630 mm cross feeds Face plate: Ã? 1250 mm Spindle speed: 5.6-280 RPM. Spindle bore: 100 mm Workpiece weight: 10.000 kg Equipped with: -Floor plates 4.500 x 2.200 mm -Powered tailstock -Operating instructions Country of origin: Germany Engine power: 45 kW Machine weight: 18,000 kg Machine Lxwxh: 8,000 x 4,000 x 2,100 mm

Code 151295 Description Facinglathe with center Make WMW NILES Model DP 1 / S 2 Serial number 261 526 149 Year of make 1986 Max. centerheight over base plate 1250 mm Max. swing over base plate 2480 mm Max. swing in Gap 3100 mm Distance between centers 4000 mm Max. workpiece weight betw. centers 10.000 kgs Spindle bore 100 mm Movement slide ( max. ) 1000 ( + 750 ) mm crossslide 630 mm toolslide 200 mm 18 Speeds 5,6 – 280 rpm Motorpower 45 kW Total power 55 kVA Machine weight total ± 18000 kgs Accessoiries 4 chuck facingplate of Ø 1250 mm Condition Machine is in very good condition

Face plate diameter: 1.250mm Center height above foundation slab: 1,250mm Weight: 19t Power: 55Kw Max. torque on the face plate: 31,500Nm Maximum workpiece mass between centres: 16,000 kg Speed range: 2.24 – 224 rpm

WMW Niles DLZ Ø 630 x 2000 mm Distance between centers: 2000 mm Swing over bed: 630 mm Swing over cross-slide: 400 mm Swing in gap: 720 mm Diametre of main spindle bore: 72 mm Power on main spindle: 19 kW Number of speeds: 28 > 1400 rpm Total power needed: 220V Weight: 4,8 ton

Parallel Lathe WMW NILES type DLZ 500 IV L 1000 Between points: 1000 mm Maxi Ø on bench: 500 mm Maxi Ø over saddle: 300 mm Spindle diameter: Ø 50 mm Spindle speed: from 28 to 1400 RPM 3-jaws chuck Ø 200 mm Threadings: Metric + Whitworth Tailstock CM4 Auto Feeds transverse + longitudinal + rapid Lubricant pump Voltage: 380 V Dimensions (L x W x H): 3000 x 1400 x 1500 mm Weight: approx 2,5 T

centre distance: 5000 mm turning diameter over bed: 4000 mm turning dia. in gap: 5000 mm spindle bore: 104 mm turning speeds: 1,4 - 71 (18x) U/min total power requirement: 30 kW weight of the machine ca.: t dimensions of the machine ca.: m 4-jaw face plate Ø 3.150 mm modular lathe! The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. width of grinding wheel: 50 mm ratio: 0 max. dia. of grinding wheel: 400 mm total power requirement: 3 kW weight of the machine ca.: 1000 kg dimensions of the machine ca.: m Pre-Dressing Device for Gear Grinding Wheels The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Chuck size: Ø 160 mm -DKRD Ø: 160 mm -Weight: 15.5 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Chuck size: Ø 160 mm -TGL: 30-2312 -Weight: 11.2 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -DH: 200x3-III -TGL: 30-2332 -Chuck size: Ø 200 mm -Weight: 16.7 kg

Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 315 mm -Passage: Ø 104 mm -Weight: 44 kg

Wedge rod feed, swivel feed, swivel swivel feed, power clamp feed -Feed size: Ø 250 mm -Weight: 35.5 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Fucking size: Ø 200 m -Through hole: Ø 54 mm -Weight: 12 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Chuck size: Ø 250 mm -Rezess: Ø 210 mm -Throughout: Ø 80 mm -Weight: 20.7 kg

Wedge bar chucks, three-jaw chucks, three-jaw lathe chucks, power chucks -Chuck size: Ø 250 mm -Short taper: 8 -Thread: M30 -Pitch: 1.5 mm -Weight: 38.5 kg

Three-jaw chuck, three-jaw lathe chuck, 3-jaw chuck -Chuck size O 200 mm -Through hole O 54 mm -Short cone 6 -according to pictures, without additional accessories -Weight 14.4kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Chuck size: Ø 250 mm -Short taper: 6 -Throughout: Ø 80 mm -Weight: 25.9 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Fucking size: Ø 200 m -Through hole: Ø 54 mm -Short taper: 5 -Hole circle: 105 mm -Weight: 16.2 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Chuck size: Ø 200 mm -Thread recording -Through hole: Ø 53 mm -Weight: 19.7 kg

Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 200 mm -Weight: 18 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Chuck size: Ø 250 mm -recess recess: Ø 210 mm -Through hole: Ø 80 mm -Weight: 18 kg

Two-jaw chuck, 2 jaw chucks, vice, face plate -Chuck size: Ø 200 mm -centrically exciting: -Passage: Ø 54 mm -Weight: 15 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Chuck size: Ø 250 mm -Cone: Ø 139 mm -Hole circle: Ø 170 mm -Through hole: Ø 80 mm -Weight: 24 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -DH250x3-III -TGL 30-2332 -Chuck size: Ø 250 mm -Cone: Ø 140 mm -Hole circle: Ø 172 mm -Through hole: Ø 80 mm -Weight: 28 kg

Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -DH B200x3x6 -TGL 30-2332 -Chuck size: Ø 200 mm -Cone: Ø 106 mm -Hole circle: Ø 135 mm -Through hole: Ø 54 mm -Weight: 15 kg