Fabricante:
(Categoria: 106)
pressure:20 tStroke:230 mmtable surface area:Ø600 mmdistance table - lower edge of ram:770 mmweight:595 kg ... mais informação
Printing capacity max. 25 t, table 600 x 600 mm, stroke max. 350 mm ... mais informação
Power of parallel/offset crankshaft: 30t/2x20t, stroke: 50mm, clamping surface: 230mm/460mm, face of tappets: 2x 30mm/110mm, average of clamping journals: 38mm. Max./min. Opening front dead center: 240mm/180mm, ejection distance: 24mm. Max./min. Band width: 80(100)mm/10(5)mm, max. feed: 120mm. Running speed: 60-180rpm, drive pulley diameter: 180mm, gear reduction: 1:4, documentation available.
Pressing force: 12.5t, stroke: 8-60mm, stroke speed: 140/min, connected load: 1kW, weight: 1.1t. ... mais informação
throat: ca. 300 mmstroke: ca. 200 mmpressure capacity max.: 35 tdie cushion hydr. pressure/stroke: 15 ttotal power requirement: 5,6 kWweight of the machine ca.: ca 2,5 tdimensions of the machine ca.: 1 x 0,9 x H 2,4 m mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Press brake edge machine edge bench press used Manufacturer: Mengele Type: C320-4B Built: 1966 last revision and repair: 2000 Location D-01587 Riesa Dimensions WxH: 6,250 x 3,650 mm Edge knife width: 6,150 mm sheet thickness at 6,000 mm bending length: approx. 7.5 mm. The machines are designed for very deep shaft bends, therefore very deep cheek recesses. Original 300 t pressing force - In 1989 the pressing force was increased to 350 t. The press is in very good condition despite its age. The machine is disassembled and ready for loading. documentation for the machine is available. Weight: about 45 t
Pressing force: 15t, stroke adjustment: 0-60mm, stroke speed: 120/min. ... mais informação
pressure:035 tthroat:225 mmstroke:8 - 100 mmno. of strokes:110 /mindistance table/ram, max. stroke up, adjustment up:400 mmtable surface area:580 x 460 mmhole in the table:250 x 150 mmtable height over floor:700 mmtable adjustable:230 mmram surface:355 x 120 mmram adjustment:70 mmpower requirement:2,2 kWweight:1,5 tdimensions (WxDxH):1,0 x 1,5 x 2,05 mclutch:rolling key overload protection in ram:mechanical
pressure:063 tthroat:450 mmstroke:8 - 100 mmno. of strokes:65 /mindistance table/ram, max. stroke up, adjustment up:415 mmtable surface area:720 x 800 mmhole in the table:280/250 mmtable height over floor:800 mmpassage to the back:290 mmram surface:450 x 280 mmram adjustment:63 mmpower requirement:7,5 kWweight:4,7 tdimensions (WxDxH):1,3 x 2,0 x 2,65 mclutch:pneumatisch overload protection in ram:mechanisch
pressure: 100 tthroat: 410 mmstroke: 8-112 mmno. of strokes doubel-strokes per min.: 55 / 82 ram - range of adjustment: 80 mmtable surface area: 950 x 700 mmram surface: 700x450 mmhole in the table: Ø 280 mmtable height: 850 mmtool hole in ram: Ø 50 mmweight of the machine ca.: 7,0 tdimensions of the machine ca.: 1400x2200x2800 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Eccentric press Manufacturer KRS (Kurt Rompel Solingen) Type EPV50, YOC 66, Printing capacity 50 t, Plunger stroke 80 mm, Weight approx. 2.500kg UVV Test Book Machine fully operational ... mais informação
pressure:200 tdistance between columns:1100 mmstroke:600 mmdistance table/ram, max. stroke up, adjustment up:1100 mmtable surface area:1000 x 1000 mmpressure of drawing cushion in table:63 tstroke of drawing cushion in table:250 mmdie cushion area:800 x 750 mmtable height over floor:800 mmram surface:1000 x 1000 mmSpeed down:400 mm/sspeed up:250 mm/sworking speed:22 - 56 mm/spower requirement:45,0 kWweight:24,0 tdimensions (WxDxH):2,4 x 1,5 x 5,9 mGerman Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 drawing cushion in table:hydraulic
Description: Capacity: 10 tonnes Collection on: 29/04/2024 or 06/05/2024  ,  ,Collection times by arrangement  , IMPORTANT: Collection times may vary if separate collection times are explicitly stated in  ,in the item description  ,Approx. Onsite Dimension. (l x w x h): 600 x 1,000 x 2,300 mm, weight approx.: 1,000 kg
pressure: 800 tdistance between columns: 600 mmstroke: 65 mmram - range of adjustment: 50 mmtable surface area: 590x650 mmram surface: 590x450 mmno. of strokes: 45 Hub/mintotal power requirement: 22 kWweight of the machine ca.: 18 tdimensions of the machine ca.: BxTxH 1700x2600x3100 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 63 tthroat: 280 mmstroke: 8-100 mmno. of strokes: 56/84 Hub/minram - range of adjustment: 63 mmtable surface area: 620x500 mmram surface: 310x260 mmhole in the table: Ø 250 mmtable height: 850 mmtool hole in ram: Ø 40 mmweight of the machine ca.: 4 tdimensions of the machine ca.: 1200x1900x2800 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Capacity, ton 1250 Stroke, mm 500 Maximum drawing depth,mm 200 Min number of no-load stroke: 14 /per min Slider adjustment, mm 315 Max. shut height between bolster plate and slider (stroke down, adjustment up), mm 1250 Table size, mm 1600 x 1800 Slider size, mm 1530 x 1800 Aperture in a table, mm 1100 x 1100 Distance between columns, mm 1600 Cushion travel, mm 200 Cushion capacity, ton 200 Maximum push force ton 31.5 main motor power, kW 125 Press overall dimensions: 5850x3100x8950 mm Press weight, kg 195000
pressure: 63 tthroat: 330 mmstroke: 8-100 mmno. of strokes: 56/84 Hub/minram - range of adjustment: 63 mmtable surface area: 850x600 mmram surface: 550x360 mmhole in the table: Ø 240 mmtable height: 800 mmtool hole in ram: Ø 40 mmweight of the machine ca.: 4,5 tdimensions of the machine ca.: 1300x2000x2700 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Eccentric press, single column press, punching machine, single column eccentric press, eccentric press, single column press -Manufacturer: BBT Presses, single column eccentric press type ER 25 with safety cage -Press guard: Nilson -Clutch: pneumatic -Pressure capacity: 25 tons -Stroke rate: 50/100 strokes/min -Stroke: adjustable 12 - 80 mm -Table size: 520 x 360 mm -Projection: 190 mm -Punching fixture: Ø 30 mm -Insert height: 310 mm -Central lubrication -Dimensions: 1180/800/H1820 mm -Weight: 1418 kg