Fabricante:
(Categoría: 101)
Inv. Num. : 7260 Type: WHN 13.4 A Producer: TOS Created: 1986, GO 2003 Parameters: Control system: MEFI CNC 859 Work table length: 1800 mm Work table width: 1600 mm Maximum table load (uniform): 12 t Maximum spindle speed: 1098 1/min X-axis travel: 3000 mm Y-axis travel: 2000 mm Z-axis travel: 800 mm W-axis travel: 1250 mm Spindle diameter: 130 mm Cone: ISO 50 Machine height: 3900 mm Machine length: 6200 mm Machine width: 5930 mm Machine weight: 32 t
The machine is in good technical condition. Working spindle diameter: 100mm Transverse table adjustment: 1250mm ... más información
bore capacity in steel (diameter): 50 mmarm length: 1600 mmworkpiece height max.: 1500 mmtable-size: 700 mmspindle taper MT: 5 spindle turning speed range: 30-1200 U/minfeed range: 0,06 - 1,0 mm/Ucrossrail adjustment horizontal: 230 - 1.570 mmcrossrail adjustment vertical: 500 - mmspindle stroke: 320 mmpower requirement: 5 kWvoltage: 400 Vtotal power requirement: kWweight of the machine ca.: 3800 kgdimensions of the machine ca.: 0,95 x 2,5 x 2,95 m- Serial-No.: 348400- automatic vertical feed- rapid clamping boring chuck Ø 3-16- machine lampThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Specifications: Drilling capacity in steel ST 60 13 mm Quick-action chuck 1 - 13 mm Drilling spindle speeds infinitely variable 630 - 5000 rpm Drilling spindle stroke 80 mm Projection 195 mm Column diameter 65 mm Table dimensions W 240 x D 260 mm Drilling unit height-adjustable by hand crank max. distance table / base plate to spindle 280 mm Drive 400 V / 0.45 kW Space requirement approx. W 300 x H 800 x D 700 mm Weight approx. 50 kg
bore diameter: 620 mmspindle diameter: 130 mmbore depth: 320 mmfeed stepless: 0 - 12 mm/minturning speeds: 10 - 70 U/minvoltage: 380 V / 50 Hztotal power requirement: 4 kWweight of the machine ca.: 1,6 tdimensions of the machine ca.: 2,0 x 1,2 x 1,3 mtransportable drilling out work, completely ready for connectiongear of drill spindle runs over LENZE planetary driveadvanced feed with LENZE direct current motor, output: 160 wattclockwise and counterclockwisewith tool holder for Ø 420 x 620 mm,tool holder for tooling equipment fabri. LENZ LPAS 3,diverse turning steelThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Inv. Num. : 5479 Type: PC W 200 HA Producer: ŠKODA Created: 1987 Parameters: Spindle drive power: 77 kW Minimum spindle speed: 0.8 1/min Maximum spindle speed: 630 1/min Mechanical feed length axis X: 4000 mm Maximum feed speed axis X: 4000 mm/min Maximum feed speed axis Y: 4000 mm/min Maximum feed speed axis Z: 4000 mm/min Cone: ISO 60 Spindle diameter: 200 mm Maximum turning-out depth: 2000 mm Spindle extension: 1600 mm Base size: 6400 x 5100 mm Ride of the stand on the bed: 5000 mm
X-travel: 550mm, y-travel: 300mm, z-travel: 280mm, max. load: 500kg, table dimensions: 950x370mm, spindle diameter: 50mm, connected load: 22kVA, controls: SIEMENS Sinumerik 810M, weight: 2.6t. ... más información
Description: Power 0.75 kW, including vice, jaw width 130 mm, max. 4000 rpm, lowering stroke 120 mmweight approx.: 450 kg, Approx. Onsite Dimension. (l x w x h): 400 x 600 x 2,000 mm ... más información
High-performance column drilling machine Offer number: 17469 Make: ALZMETALL Type: AB 4 SV Machine No: 18498 Built: 1987 Technical data: - Drilling capacity in steel ST 60 40 mm - Drilling capacity in steel ST 60 50 mm - Thread cutting device - Drilling spindle holder MK 4 - Drilling spindle stroke 180 mm - Drilling spindle speeds infinitely adjustable with pre-bedding - Level 1 - 80 - 210 rpm - Level 2 - 210 - 765 rpm - Extension 330 mm - 3 feeds 0.1 - 0.2 - 0.3 rpm - hydr. Feed cylinder for semi-autom. Workflow + Rapid Response - Table with 2 T-slots 720 x 360 mm - height-adjustable via rack with hand crank - max. distance table - drilling spindle approx. 780 mm - maximum distance machined base plate - drilling spindle 1250 mm - Lighting - Coolant device - Swivel arm control panel - Drive 400 V 4 kW - Space requireme ...
- Drilling capacity in St 60, 30 mm - Short spindle MK 3 - Spindle stroke 120 mm - Projection 293 mm - Table support 420 x 300 mm, 2 T-slots - Machined base plate 320 x 329 mm, 2 T-slots - Distance base plate - drill chuck 1000 mm - Feed via turnstile - Weight 220 kg - Spindle speed 160 - 2250 rpm. - Operating voltage 380V-50Hz - Infinitely variable speed adjustment, by means of an adjustment lever - Engine speed in 2 stages, 700/1435 rpm - Tapping device with rotation direction change after reaching the end stops - Coolant device fully installed. - Coolant tank in machine base - Work light with LED - RÖHM drill chuck 1 - 16 mm - Precision machine vice new (test winner)
Control unit, control panel, control panel, control unit, keyboard, screen, controller, hand terminal, control unit-Manufacturer: Bierrebi LEA SRL. Control module from automatic cutting machine Bierrebi TA 103-Circuit board: LEA SRL. Type LEA 1000 LEA 1002-Dimensions: 265/125/H100 mm-Weight: 2.0 kg
Control unit, control panel, control panel, control unit, keyboard, screen, controller, hand terminal, control unit-Manufacturer: Bierrebi LEA SRL. Control module from automatic cutting machine Bierrebi TA 103-Circuit board: LEA SRL. Type LEA 1004 2.028.01.063.02-Dimensions: 400/100/H50 mm-Weight: 0.4 kg
Control unit, control panel, control panel, control unit, keyboard, screen, controller, hand terminal, control unit-Manufacturer: Bierrebi LEA SRL. Control module from automatic cutting machine Bierrebi TA 103-Circuit board: LEA SRL. Type LEA 1011 2.028.01.067.01-Dimensions: 330/125/H50 mm-Weight: 0.9 kg
Control unit, control panel, control panel, control unit, keyboard, screen, controller, hand terminal, control unit-Manufacturer: Bierrebi LEA SRL. Control module from automatic cutting machine Bierrebi TA 103-Circuit board: LEA SRL. Type LEA 1020-Dimensions: 300/280/H80 mm-Weight: 3 kg ... más información
A complete Wagner WBX 1003 boring mill is available. Control: CNC Systems WB 1000, documentation is available. ... más información
Main technical characteristics: Processing control digital indication; Spindle diameter mm, 200; Cone mm, 60; Quill size mm, 5205200; Maximum spindle torque: Cutter diameter 160mm. – 8600 Kn. Maximum depth of boring by spindle in mm., 2000; The maximum extension depth of the quill in mm., 1600; Movement of the headstock on the rack in mm., 3000/4000; Moving the rack along the frame in mm., 4000/20000; Dimensions and weight: -Height of a bed in mm., 500; Width of bed guides in mm., 2000; Width of rack guides in mm., 1700; Total machine power 180kVA Power of the main drive in kW, 77. The machine is equipped with a rotary table weighing 49000 kg. Machine weight 102000 kg. We are ready to discuss the price and all terms, please contact us for further discussion.
x-travel: 500 mmy-travel: 380 mmz-travel: 300 mmControl: FANUC total power requirement: 12 kWweight of the machine ca.: 2300 kgdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
Multi-spindle head, multi-spindle drill head, drilling gear -Multispindle head -drill: max. 11 -Cardan shafts: 5x available -Largest drilling pattern Dimensions of the drill: 100 x 230 mm -Weight: 27 kg -Multi-spindle heads are: variable tools -for various processing such as: drilling, thread cutting, countersinking, reaming, -with which several holes can be machined at once -Dimensions: 450/190/H660 mm -Weight: 27 kg
aschinella details Warehouse number 1105-03656 Machine Type Machining Center - Vertical Make BROTHER Type TC 211 Year of construction 1987 Control type CNC Storage location HAGUENAU Country of origin Japan Delivery time immediately Freight base freely loaded from stock Price Technical details x-travel 420 mm y-travel 220 mm z-travel 200 mm Spindle cone 30 NT Speed range 1-4000 rpm Spindle motor 3.5 kW Table clamping surface 600 x 300 mm Number of tools in the magazine 10 pieces Rapid traverse 20 / 15 m/min Information WELL PRESERVED MACHINE