Fabricante:
(Categoria: 106)
Capacity 250 ton Kinetic energy of moving parts at the end of max. ram stroke 13,5 kj Max. ram stroke 400 mm Number of ram stokes (SPM) 34 Slide clearance 560 mm Ram size (front-back 560 mm Table size 670 x 750 mm Lower ejector capacity 16 ton Lower ejector movement 105 mm Main drive motor powe 15 kW Press dimensions 3710 x 1925 x 4415 mm Press weight 18000 kg
Capacity :10 tons, Weight of falling part,nominal mass of drop parts without upper instr.:9 tons, Effective working kinetic energy after blow :25000 kg mtr., Max. working ram stroke :1400 mm, Max no of blows : 30/min , Distance between slides : 1000 mm, Shut height : 775 mm , Ram size front to back :1200 mm, Bolster size front to back :1200 mm, Air pressure : 7-9 MPA , Height of instruments : 450 min., Die-holder front to back dimensions: 1400 mm, Height above floor level: 7270 mm, Hammer dimensions : 4400x10420x2700 mm, Weight (less anvil block): 73.5 ton, Weight of anvil block : 203.8 tons.
Pressing of profiles up to a profile height of 68 mm Pressing force: 40 kN Pneumatically movable counter bearing, mechanically locked With support arms Weight: approx. 240 kg ... mais informação
YOM (2008); Max. Roll Length 17 Meter; Min. Daylight between Roller 960mm; Max. Ram stroke 1040 mm; Top Roll diam. 480 mm; Bottom Roll 400 mm; 6 sets of Back-up Rolls; Min/Max Bottom Roll Centers 500/800 mm; Pressing Speed 1 to 6 mm/sec. ram approach 60 mm/sec; main motor 125 HP. Including control panel, panel boxes and conveyors. Weight: 600.000,00 Capacity: 2000 TON, Working size: 17000mm x 35t, 5500 x 40t
(2007); Max. Roll Length 20 M; Min. Daylight between Roller 960 mm; Max. Ram stroke 1050 mm; Top Roll diam. 500 mm; Bottom Roll 420 mm; 8 sets of Back-up Rolls; Min/Max Bottom Roll Centers 500/800 mm; Pressing Speed 1 to 6 mm/sec. Ram Approach 60 mm/sec; Main Motor 125 HP. Including Spare for Bottom Roller, control panel, panel boxes and conveyors. Capacity: 2200 TON, Working size: 20,000mm x 25t, 5,000mm x 40t
Control: STE 328-89-1 1/2" complete TOX Powerhouse: S75.160.200.12D Table size: 996 x 695 mm Installation height: 600 mm Total stroke: 150 mm Power stroke: 10 mm Weight: 5700 kg Electrical connection 230 V ... mais informação
Capacity: 125 ton, Strokes per minute: 85-500 / min, Slide: 870 x 550 mm, Plate width: 260 mm, Year of manufacturing: 1980 ... mais informação
VORONEZH K8544 Hot Forging press YEAR : 1980 / 2008 OVERHAUL AND INSTALLED FORCE : 2500ton RAM STROKE : 350 mm RAM SIZE : 1120X1070 mm TABLE OVERALL SIZE : 1400X1200 mm NUMBER OF STROKES IN CONTINUOUS MODE : 60 NUMBER OF STROKES IN MANUAL MODE : 26 SHUT HEIGHT : 890 mm STROKE OF UPPER KNOCK OUT : 60 mm STOROKE OF LOWER KNOCK OUT : 70 mm MAIN MOTOR : 132KW (CHANGED TO HYUDAI HEAVY Y2012) PRESS OVERALL DIMENSION : 5380X4680X6400 mm HYDRAULIC BOLSTER NEW IN 2007 CONDITION : VERY GOOD WORKING CONDITIONS Trimming press available
2000 Ton Sumitomo Hot Forging Press line Year 2006 Stroke 350 mm (13.78") Strokes per min 75 Shut height 850 mm (33.47") SlideAdj. 7 mm (.27") Ram size 1200 mm LR X 1300 mm FB Bed size 1320 mm LR X 1300 mm FB 4 stage transfer system Slide knockout Bottom knockout Scrap System Dual Die Changer Extra Die Shoes Billet Heater and Billet Saw Also Available This line was used by HONDA to make transmission gears, It takes a billet, cuts it to size, heats it to 1300 C then the press hits it 4 times. It can determine good from bad parts, the bad parts get sent to a quench tank, the good parts get sent into a cool down conveyor that you can pick the parts up by hand at the end. The entire system was ran by one operator.
IHI Transfer Press Model SL4-1600-450-220. With NC Feeder, Transfer System including Robots. New : 1984 Capacity : 1600 ton Stroke : 850mm Die height :1400mm Slide Adjustment : 500mm No. of Stroke : 16R.P.M Bolster Area : 4500 x 2200mm Clutch working Air Pressure : 4.5kg/cm2 ... mais informação
Maker: SUMITOMO HEAVY INDUSTRIES (made in Japan) Model: FPA-3000 Year: 1985 (2) Capacity & main specification 1) Capacity: 3000tf 2) Ability Limit Point: 5mm 3) Allowable eccentric load: 3000tf 4) Allowable eccentric distance: L&R 350mm 5) Slide stroke: 350mm 6) Slide stroke speed: 20~50spm 7) Stroke number: 20tpm(Max) 8) Shut height: 1200mm 9) Slide adjust distance: 10mm 10) Bed hard plate dimensions: RL 1300mm x FB 1500mm 11) Slide dimensions: RL 1200mm x FB 1400mm 12) Slide knockout capacity: Total 20tf (pin number: 4ea) 13) SKO stroke: 50mm ( adjust up) 40mm ( adjust down) 14) Bottom knockout capacity: 50tf (pin number 4ea) 15) BKO stroke: 20~30mm 16) Upright internal dimensions: RL 1400mm 17) Main motor: DC 200kw x 1450rpm 440V 18) Floor height: 6800mm 19) Working height: 1030mm 20) Side opening: FB 1000mm x TB 1400mm 21) Flywheel energy: 200tf-m (50spm) ...
(2) Asahi Sunac THP500-6 horizontal forging press (heading machine) Year: 2008 First stroke: 24 mm Second stroke: 50 mm Kickout power: 150 kN Open height: 625 mm Closed height: 425 mm Die (WxL): 500x490 mm Punch (WxL): 250x350 mm Ram stroke: 200 mm Forging force: 5000 kN Cycling time: 6.5 sec Crank speed: 60 RPM Machine weight: 28 t
Hot forging press Kurimoto C2F-16 Year: 2002 Capacity: 1600 ton Stroke: 200 mm Stroke per minute: 60 Die height: 707 mm Bolster area: 1265x890 mm Adapter area: 930x1065 mm Main motor: 75kW, 480V ... mais informação
Praege machine Hydrualic press NULL for rounds of 35 mm For sale comes from a stock release a used but well preserved fully functional punch or praegepress. Steel rounds were used with this machine. max. round diameter: 35 mm incl. various stamps: A22 / A34 / A41 / A43 / A50 / A60 Drop height: 920 mm with hydraulic unit Machine comes from a warehouse breakdown of a large German industrial group and was accordingly equipped with UVV compliant. Space requirement LxWxH: 1000 x 900 x 1400 mm Weight: 335 kg Price is understood plus VAT free loaded warehouse Giessen Changes / errors in the technical data as well as intermediate sale reserved Seller Offer No. resale 6753
45 to VAT not identifiable Please inquire with the place of postcode and whether there is an unloading possibility. More pictures on request . ... mais informação
Press type: PME 315 T Drive system: Eccentric Type of used tools Progressive Nominal force: 3150 kN Rating above BDC mm Material flow L->R - Maximum SPM: 75 1/min Minimum SPM: 20 1/min Maximum shut height: 525 mm Minimal shut heigh:t 325 mm Slide adjustment: 130 mm Maximum slide stroke: 210 mm Minimum slide stroke: 40 mm Bolster specification Bolster dimension: 2220 x 1225 mm T-slots in bolster: T28 H8 DIN650 - Draw cushion N/A - Draw cushion stroke: N/A mm Draw cushion force: N/A kN Draw cushon dimension: N/A mm Maximum weight: kg Ram specification Ram dimension: 2220 x 1225 mm T-slots in ram: T28 H8 DIN650 - Max. upper die weight: 3600 kg Tool manipulation Tool is manipulated by forklift - Max. tool weight: 5500 kg Forks size/pitch: 150x60/940 mm Lower die clamp height: 50 mm Upper die clamp height: 50 mm Tool locating (centering) stůl/bolster ...
Mechanical Press KAISER 315 TON. Model: V 315 WR/2340 Condition: good, complete Technical details: Force: 315 T Dimensioni piano: 2280x1250 mm Slide size: 2000x1200 mm Slide travel: 280 mm Slide adjustment: 150 mm Mold heigh: 500 mm Number of strokes: 20-60 per mimute
Erfurt Press, Mechanic Press, H – 3m, 500 T, table 2800 x 2000mm ( it is extented for 10 cm each side – table and slide) ... mais informação
Muller Press hydraulic press BZE 1000 T, double action, table 2600 x 2250mm ... mais informação
Very good machine, offer with feeded Table dimension: 4600 x 2200 Between columnsL 5022 ... mais informação