advanced search
378 results
used
Puller and needle transport machine with thread cutter and 220 volt servo motor
used
from 500 euro Many different blind stitching machines in the warehouse for every operation
New in: 2008
used
FLEISSNER, AB 3,500 mm, with 6 drums, 1,400 mm diameter, built approx. 1985, but overhauled in 2008 and equipped with new motors and burners. Up to 250°C. With natural gas burners 1000/400 kW SIEMENS S7 controller from 2008 with touch screen Motors with frequency converter, 50 m per minute, up to 250 °C
New in: 1985
used
1 SUCKER MULLER high performance sizing machine for cotton warps year 1985, composed of: beam creel type ZA for 16 beams, device for feeding from sectional beam, 1st sizing unit type SD M1, roller width 2000 mm, double dip, double nip with pressure adjustment, 2nd sizing unit type SD M2, roller width 2000 mm, double dip, double nip with pressure adjustment, cylinder dryer type ZT-ZG, steam heated, total 8 cylinders (6 of these cylinders are teflonized), diameter 800 mm, beaming unit WN10, maximal beam pipe width 2700 mm, working width 2400 mm machine supplied with size kitchen
New in: 2018
used
1 LAFER carbon brush emerising/peaching machine type ULTRASOFT TWIN TOUCH, year 2018, table width 2200 mm, 2 brushing rollers, entry and exit in the same side, plaiter exit, dust suction and filters
New in: 2014
used
1 MCS high temperature jet dyeing machine type DYNAMICA DYN EF 3XJ HT, 3 chamber, capacity 750 Kg, year 2014, HIDROVARIO nozzles with adjustable section, dye bath preparation tank behind the machine, 2 addition vats with mixer), TERMOELETTRONICA fully automatic dye process controller, machine fully inverter controlled
used
1 KUSTERS 3-bowl rolling, glazing calander type 213.50-1800 3 bowls face roller width 2000 mm, working width 1800 mm Year 1990
New in: 2005
used
1 IBELUS laboratory HT beaker dyeing machine, type LABIbelus 12 Infra Red, with 1 set of 12 high temperature beakers, maximal dyeing temperature 140º C, dye cycle controller IBELUS type IL-720
New in: 1995
used
1 BENNINGER sectional warping machine type BEN-ERGOTRONIC, working width 200 cm, year 1995, machine supplied with 2 trolley creels type BEN-CREEL, each 640 spindles (8 stores x 40 columns x 2 sides), vertical gauge 240 mm, horizontal gauge 240 mm
New in: 1989
used
1 BENNINGER sectional warping machine type SUPERTRONIC, working width 220 cm, year 1989, machine supplied with 2 trolley creels type BEN-CREEL from the year 1999, each 640 spindles (8 stores x 40 columns x 2 sides), vertical gauge 240 mm, horizontal gauge 240 mm
New in: 1999
used
1 TRÜTZSCHLER opening line year 1999 composed of: conveyor feed with 500 cm length and 120 cm width, 1 TRÜTZSCHLER type BOWA with weigth pan, 2 TRÜTZSCHLER weighing feeder type PWSE 1200, 1 TRÜTZSCHLER Tuftmixer type FMN, 1 TRÜTZSCHLER fine opener Tuftomat type TFV1 1 TRÜTZSCHLER opening line year 1999 composed of: conveyor feed with 500 cm length and 120 cm width, 1 TRÜTZSCHLER bale opener type BO 1200, year 1999, 1 TRÜTZSCHLER fine opener Tuftomat type TFV1, year 1999 3 TRÜTZSCHLER material reserve with trunk and condensor type MS, year 1999 1 TRÜTZSCHLER fine opener with feed trunk and condensor type FD-S, year 2004
New in: 1992
used
3 RIETER cards type C4-A, year 1992, with TRÜTZSCHLER chute feed system type FBK 533 (year 2004), AutoSilver control type EZA–1, auto lever, auto doffer, pot diameter 60 cm, pot height 110 cm 1 RIETER card type C4, year 1987, with TRÜTZSCHLER chute feed system type FBK 533 (year 1999), AutoSilver control type EZA–1, auto lever, auto doffer, pot diameter 60 cm, pot height 110 cm
used
1 POLYTEX pinking machine type ZO-30, cutting width 300 mm, machine supplied with 2 cutting knives: 1 new serrated knife with 4 mm serration gauge, 1 flat straight knife table size 605 mm x 315 mm, manual actuation
used
1 KAPPA pinking machine type 41L, cutting width 410 mm, machine supplied with 3 cutting knives: 1 serrated knife with 4 mm gauge serration installed, 1 serrated knife with 4 mm gauge serration spare, 1 flat straight knife, table size 900 mm x 435 mm, manual actuation
used
1 POLYTEX pinking machine type ZP (Zigzag cutting), knife width 1020 mm, stroke up to 65 mm height, up to 50 cuts per minute, machine equipped with precise hand lever feed mechanism, serrated knife with 5 mm gauge serrations, with FASNACHT security light guards, with laser cut indicator, motor power 2,2 kW, 3 x 380 V, 50 Hz, machine in immaculate condition as you can observe in the attached pictures.
used
1 GALAN fancy yarn twister type Mini PR-F/3 MP, 6 spindles, ring diameter 120 mm, tube adjustable up to 500 mm, fully electronic control through step-by-step motors, electronic programmer type GTG-S-6. This machine was bought for a laboratory and has never really been used
used
1 IMPERIA pinking machine type E800 (Zigzag cutting), knife width 830 mm, working width up to 800 mm, machine equipped with precise hand lever feed mechanism, serrated knife with 5 mm gauge, with security light guards, 3 x 380 V, 50 Hz, 2.2 kW machine with setting for 2 pattern dimensions (normally supplied with 1 only), machine delivered with total 2 knifes: 1 knife installed with gauge 5 mm, 1 knife spare 5 mm gauge, machine delivered with 2 new cutting boards (one to be used and one as spare)
used
1 LORIS BELLINI high temp high temperature vertical cone/bobbin dyeing machine type RBNV 270/975, year 2001, capacity 5 Kg per batch, autoclave diameter 270 mm, delivered with 1 carrier with 1 sword, sword useful loading height 975 mm, add vessel
used
2 LORIS BELLINI high temp high temperature vertical cone/bobbin dyeing machine type RBNV 550/975, year 2001 and 1989, capacity each 20 Kg, autoclave diameter 550 mm, The 2 machines are delivered with total 2 bobbin carriers with 4 swords each, each word has a useful loading height 975 mm, add vessel on each machine, the 2 machines share the same electrical cabinet which was supplied by LORIS BELLINI in 2001
used
1 LORIS BELLINI high temp high temperature vertical cone/bobbin dyeing machine type RBNV 840/975, year 1998, capacity 40 Kg, autoclave diameter 840 mm, delivered with: 2 carriers with 8 swords each, each word has a useful loading height 850 mm, 1 carrier for bumps or loose stock inside diameter 750 mm and core diameter 300 mm and useful height 800 mm, add vessel with mixer