buzuluk rubber machines used for sale

Knife Drawing No. 05714-223C1

Guided from bronze Drawing No. 05714 -227D1

pneumatic Bale cutter max. Width 550 mm max. Length 800 mm Blade stroke 280 mm

Bull gear

Break

1 x Buzuluk 240 litre Internal mixer Model: 14630, year: Dec 2008 (body and hopper), Batch size: 200 kgs, Drilled sides, Self sealing type dust seals, Oil injection, Hydraulic drop door with linear actuator and toggle latch, Stellite faced drop door, Two wing tangential rotors. 20in pneumatic hopper. 3 zone TCU Full unidrive gearbox (Make Skoda), with 630kW, 6000V, 739rpm, 73.5A slip ring motor and Oil filled starter. In very good condition.

1 x BUZULUK 1920mm wide Four-roll 'L' calender - Type: 03506 - Rolls dia 710x1920 mm - Year of manufacture: 1989 - Peripherally drilled rolls - High pressure hot water heating (Steam 1.6 and 3.2 MPa) - Motorised nip adjustment to rolls 1, 2 and 4 (30mm adjustment) - Cross axis on roll 3 (0-30mm) - Roller Bearings - Unidrive gearbox with DC motor to each roll - Rolls 1 and 4: 46 kW - Rolls 2 and 3: 77 kW - Working speed of 4th roll max 60m/min In very good condition.

Tangential nett volume 70 l drop door AC motor 320 kW / 380 V / 50 Hz, 1483 RPM Year 1987

Tangential Chamber volume 70 l, hydraulic drop door AC motor 320 kW / 380V / 50 Hz, 1483 RPM Year 1987 Previously used for PVC.

front roller 600 x 1500 for mixing mill Buzuluk 14240 (KG40) Unused

rear roller 600 x 1500 for mixing mill Buzuluk 14240 (KG40) unused

Input pinion Drawings Nr. 20015-76D2

Central gear Drawing no. 20015-97

Side wheel Drawing no. 20015-81, 20015-82D2

big wheel Drawing no. 20015-19

NIP adjustment nut Drawing No. 14240-216E3

NIP adjustment screw Drawing no. 14240-517

Worm gear (small) Drawing no. 14240-546D1

Screw (small) Drawing no. 14203-461D1

Key data: 300 , 600

Rollers: dia. 300 x 600 mm Roll surface: smooth Rollers type: hollow bored NIP adjustment: Manuel Engine: 22 kW

NIP adjustment screw Drawing No. 14204-1168D1

NIP adjustment screw with more grooves

Pinion Drawing No. 14240-113 z=26

Bull gear z=82

Seal Drawing No. 14430-2815C2

Seal Drawing No. 14430-2818C2

Seal Drawing No. 14430-2824C2

Gearbox TSA 031 370-1-07 Manufacturer VSS Kosice for mixing mill Buzuluk 660x2100 mm , Type 14821 for right side i = 10:1

Bull gear Drawing No. 14272 -161 C1 z = 113

Pinion Drwaing No. 14272 - 167 C1 z=20

Pinion Drawing No. 14821- 167 C9 z = 23

Drive 210 kW / 985 rpm, 380 V, with starter

Covers for bull gear and friction wheels

front roll 560x1500 for mixing mill Buzuluk 14823

rear roll 560x1500 for mixing mill Buzuluk 14823

3 to 5-Roll calender Buzuluk Number of rolls: 4 pcs. Roll diameter: 150 mm Roll length: 400 mm

Key data: 400 mm, 1000 mm

Buzuluk 14231 CE conversion in 2010 Antifriction bearing Motor: 55 kW Motorized NIP adjustment Baseplate

The main machines in the line: fluid mixer Trusioma hot and cold KO-kneader BUSS Mixing mill Buzuluk 660x2100 mm 4-roll calender Buzuluk 700x1800 mm, inverted "L" tempering and stretching device behind the calender – roller track film thickness profile measuring device winding device

roll diameter: 660/700 mm roll length: 2100/1800 mm rolls drilled: Kernbohrung nip adjustment: motorisch drive power:: -- kW Condition: used Specification: 4-Roll L-Calender - Line - second-hand 4-roll Buzuluk L-calender 700x1800 Mixing mill Buzuluk 660x2100 Complete 4-roll L-calender line. The line was used for the production of transparent PVC. However, the basic machines can also be used for rubber. The most important machines in the line: Pos. 8: Liquid mixer make Trusionma hot and cold Pos. 10: KO Kneader make BUSS Item 12: Buzuluk 660x2100 mixing roller mill Item 14: 4-roll L-calender make Buzuluk 700x1800 Items 15-19: Tempering and basin equipment behind the calender Roller conveyor Item 20: Layer thickness profile measuring device Item 23: Rewinding device The system was used for transparent soft PVC. Machines are still installed. The data for this ad was  ...

Key data: 660 mm, 2100 mm

4 nos. Buzuluk 84" Mills available! Drilled Rolls, Rollerbearings, electrical Nip adj., Bullgear Drive 2 x left Hand Drive 2 x Right Hand Drive Description attached!

roll diameter: 700 mm roll length: 1800 mm rolls drilled: Kernbohrung nip adjustment: motorisch drive power:: -- kW Condition: used Specification: 4-roll L-calender 700x1800 - used - BUZULUK 4-roll L-calender 700x1800 Type: 04706/P1 - Reverse L-shaped roller arrangement - The system was used for the production of PVC films - Film thickness: 0.05 - 1 mm - Can also be used for rubber - Maximum product width: 1,600 mm - Working speed: 6 - 60 m/min - System features roll bending and cross axis - BUZULUK temperature control and stretching device behind the calender - Year of manufacture: 1996 - Consists of 13 stretching and pulling rollers behind the last roller of the calender - The device is supplemented by 4 polishing rolls, - these 4 polishing rolls are temperature-controlled, - all rolls are driven via cardan joints, - all rolls can be temperature-controlled and  ...

Key data: 300 mm, 600 mm

Diameter: 300 mm Length: 600 mm Surface: smooth NIP setting: manual Motor: 30 kW Siemens Dimensions: approx. 1700 x 1560 x 1635 mm Weight: approx. 3000 kg CE marked from 2018 (engine with reverse gear, knee emergency stop)

Tyre testing machine - static balancer for passenger tyres. Tyre size from 15 "to 18" (20") CE certified More details see the attached description!

Mesh belt for AUMA / Rotocure new and unused Length: 14100mm Width: 2250mm

Berstorff Rotocure AUMA 20-S Drum dia: 2000mm Drum width: 2600mm Sandvic Steelbelt Description attached!

machine measurements: 1500 x 2400 x 1150 mm machine weight: -- kg power capacity: 12 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

machine measurements: 3.000 mm machine weight: -- kg power capacity: 90 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cross-section width:: -- mm cross-section heigth:: -- mm feed:: -- mm speed of feed:: 0,4 - 20 m/min The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cross-section width:: 85 mm cross-section heigth:: 25 - 40 mm feed:: 1 - 999,999,9 mm speed of feed:: 60 m/min cuts max.:: 100 - 120 Schnitte/m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cross-section width:: 5 Schläuche 3-5 mm cross-section heigth:: 3 - 20 mm feed:: 1,5 - 50 mm Condition: used, very good condition only approx. 1 year in production Specification: circular knife cutting machine for slices and rings - small cutting machine with high-speed rotating circular knife - feed and knife movement, pneumatic - Tube or strand diameter min.: 3 mm - Tube or strand diameter min.: 20 mm - Feed (ring or strand length): 1.5 - 50 mm - Output depending on material max.: 60 strokes/min - Optionally, the following can be cut 5 tubes or strands: diameter 3 mm to 5 mm 4 tubes or strands: diameter 5 mm to 7 mm 3 hoses or strands: diameter 7 mm to 12 mm 2 hoses or strands: diameter 12 mm to 15 mm 1 hose or string: diameter 15 mm to 20 mm - Power requirement approx.: 0.37 kW - Air supply min.:  ...

Fogg & Young Bale Cutter

cross-section width:: 700 mm cross-section heigth:: 500 mm feed:: -- mm Condition: used, overhauled Specification: splitter for rubber bales - overhauled with CE - cross section width max.ca.: 700 mm - cross section height max. approx.: 500 mm - cutting force approx.: 10 tons - AC motor: 4 kW, 400 V, 50 Hz - Infeed roller conveyor for product transport - Machine stands on a raised pedestal - Two-hand safety control for driving the blade movement - Safety guard according to current standards - New control cabinet - New on-board system machine - Operating and maintenance manual in English - CE marking - Paintwork: according to customer requirements - Refurbished with 1 year warranty - CE marking, Option: - Output roller conveyor new The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cross-section width:: 100 mm cross-section heigth:: 40 mm feed:: 2 - 999.999,9 mm Condition: new, Specification: Impact knife cutting machine CC-600/40 for hoses and profiles - contact length: 600 mm - product diameter: 40 mm - belt width: 100 mm - Tractive force: 400 N to 800 N - Drive: 2 drives upper and lower belt - Conveyor belt speed: 100 m/min - Drive feed, cutting motor: Servo drives - Cutting capacity with blade max.: 4,000 1/min - Connected load: 3.5 kW - Dimensions L/H/B: 1,900 x 1,650 x 960 mm - Weight approx.: 580 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Press (n°1) Upstroking Manufacturer: Agila Closing force: 850 Ton Year 1997 hydraulic Steam Platens : 3 2 cavities (250 mm opening) Size heating platens: 1100 x 1400 x 76 mm Diam. piston 650 mm Hydraulic pressure: max. 250 BAR Hydraulic tank: 500 L Complete manual included Size press 2400 x 1400 x 4200 mm (LWH) Weight +/- 23.000 kg

REP H48Y10W Horizontal Injection Moulding Machine Year of construction 2005 Machine Parameters Volume [cm3] 1000 Clamping force [kN] 1930 Injection pressure [bar] 1500 Moulds dimension [mm] 450x450 Tonnage 1.9t Platen size: 450x450 Cycles: 2,220,383 General condition: operational Dims [mm]: 4200 L x 1400 W x 2200 H Weight [kg]: 6750

Refer to code 1049 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

Z-Splicing Machine Make: Z-AUTOMATION Model: Z splicing stand alone Year 2014 8 kW, 6 bar Profile Cross sections 50 x 40 mm 2 - 4 splicing cavities Length 4600 mm Siemens Simatic HMI touch screen control Foot pedal control Emergency kill switch

Merkle Slitter 500mm wide

USI Cumberland Grinder / Granulator 28x20 50 Hp 8mm Grid 2 new dead blades 3 sharpened fly blades One new start / stop control box

cross-section width:: 40 (45) mm cross-section heigth:: 25 mm feed:: 1 - 999.999,9 mm speed of feed:: 1 - 60 m/min cuts max.:: 100 Schnitte/m Condition: used, Specification: circular knife cutting machine - second-hand for cutting rings, discs and profiles - diameter max.: 45 mm - 3 hoses or strands: 6 - 20 mm - 2 hoses or strands: 20 - 30 mm - 1 hose or string: 30 - 45 mm - cross section width max.: 40 mm - cross-section height max.: 25 mm - feed speed: 1 - 60 m/min, infinitely variable - Cutting capacity max.: 100 cuts/min depending on material and cutting length - Cutting length: 1 - 999.999,9 mm - Step jump: 0.1 mm - Feed by servo drive - Cutting by servo drive - Pulsed feed - Connected load approx.: 5 kW - Operating voltage: 3 x 400V, 50Hz, PE - Weight approx.: 550 kg - Dimensions (L/W/H): 1,940 x 890 x 175 ...

cross-section width:: 800 mm cross-section heigth:: 15 mm feed:: ab ca. 5 mm speed of feed:: m/min cuts max.:: Schnitte/m condition: used, overhauled Specification: Panel cutting machine - overhauled with CE - Section width max.approx.: 800 mm - Section height max.: 15 mm, depending on the hardness of the rubber sheets - Cutting length from approx.: 5 mm (depending on material) - cutting force approx.: 10 tons - Connected load approx.: 1.8 kW - Painting: green - Operating voltage: 3 x 400V, 50Hz, N, PE - Dimensions approx.: 1,200 x 1,450 x 1,950 mm - Safety devices according to current standards, - New on-board system machine, - New control cabinet with PLC system Siemens S7-1200, - CE marking, - Instructions for use and maintenance in English or German language The data for this ad was created with ModulMWS - the s ...

Press force max.:: 1.000 kN heating plates:: 480 x 520 mm electrically heated:: °C piston stroke:: ca. 500 mm no. of stages:: 1 Condition: Used, overhauled Specification: 4-column vulcanising press 480 x 520 mm, used - closing force: 100 t - closing: from top to bottom - heating plates: 2 electric plates - New heating platens - Dimensions of heating plates: 480 x 520 mm - Distance between heating platens approx.: 500 mm - AC motor: 5,5 kW - New electric valves - New control cabinet with Siemens 7 touch panel - SPS system Siemens S7-1200 - Frequency converter make Schneider - New cabling - Light curtains in the front operating area Overhauled according to CE standard safety regulations Operating and maintenance instructions in German Warranty: 1 year The data for this ad was created with ModulMWS - the software solution of LogoTech oH ...

cross-section width:: Schläuche max. 11 mm cross-section heigth:: 11 mm feed:: 0,5 - 100.000 mm Condition: used, very good condition Specification: universal cutting machine with roller drive for hoses - small cutting machine for hoses - feed unit: roller drive - microcontroller control: 80537 - cutting unit: pneumatic - Type of cut: Blade cut - Industrial blade: for PVC hoses - Max. hose diameter: 11 mm - Maintenance unit: yes - Max. feed speed: 1 - 50 m/min - Cutting capacity max.: 450 cuts/min depending on the cutting length - Cutting force approx.: 500 N at 6 bar - Cutting length: 0.5 - 100,000 mm - Resolution/step change: 0.5 mm - Operating voltage: 230V, 50-60 Hz - Compressed air: 5 - 6 bar - Air consumption per stroke approx.: 0.2 l/stroke at 6 bar - Paint finish: RAL 7035 light grey - No docum ...

Barwell Cryogenic Deflashing and Deburring Machine Freeze Trim Chamber Model BFT10

Merkle Slitter Cutting width 1m Overall dims: 1.4m wide x 700mm deep x 1m high Weight: 500kgs

Merkle 500mm wide Slitter

speed of feed:: 50 m/min feed:: 5 - 99.999,9 mm cuts max.:: 70 - 80 Schnitte/m cross-section width:: 40 mm cross-section heigth:: 40 mm Condition: NEW, Specification: Hose and corrugated pipe cutting machine electric cutting machine - Cutting unit: Window cut with cutting bushes - Material diameter approx.: 4 - 40 mm - Transport by two drive belts - Max. distance between the belts: 45 mm - Belt adjustment via motor, adjustment via control panel - Belt adjustment via the centre - with a maximum speed of approx.: 50 m/min - Electrical contact pressure of the drive belts - Electronic length measurement from 5 - 99,999.9 mm Digital display - Step change: 0.1 mm - Cutting via electric motor - Quantity selectable: 1 to 99,999 Display digital - Cutting capacity approx.: 70 - 80 pieces/min at 100 mm l ...

Press force max.:: 1600 kN heating plates:: 400 x 400 mm electrically heated:: -- °C heating power:: 9,92 kW piston stroke:: 400 mm no. of stages:: 1 Condition: Used, Specification: Press 400 x 400 mm, second-hand steel frame construction - Clamping force: 160 tonnes - pressure force: 1600 kN - Operating pressure: 300 bar - Closing: from bottom to top - Heating platens: 2 electric platens - Heating power: 4.96 kW/platen - Heating platen dimensions: 400 x 400 mm - Specific pressing pressure: 1000 N/cm² - Distance between the heating platens: 500 mm - Piston stroke: 400 mm - Piston diameter: 260 mm - AC motor power: 7.5 kW - Pneumatic protective cover in the front area, - lifting device - Sliding table - Approx. dimensions: 1,760 x 1,150 mm - System height approx.: 2,470 mm - Weight approx.: kg The data for this ad was cr ...

Merkle Metzner Profile Automatic Cutting Machine Model XCL Material direction right to left Type of cut: Die cut/scissor cut Year 2002 Belt feed Width of belt 100mm Contact belt 200/400mm Poly-v belts Material acceptance: max. 100x30mm Drive Stepping motor, 3 phases Max. feed rate 40m/min Max. torque 420 Ncm Connection values Voltage 230V Pressure: 6 bar

John Marshall Cutter

Autogil Cutter

MDR 2000 Rheometer Manuf.: Alpha Model 81001 220V 5amps Power 1000 VA Air pressure required PSI 120 max. / 70 min.

Press force max.:: 3000 kN heating plates:: 600 x 630 mm electrically heated:: °C heating power:: kW piston stroke:: 420 mm no. of stages:: 1 Condition: Used, reconditioned Specification: Press 600 x 630 mm, second-hand - clamping force: 300 tonnes (3,000 kN) - closing: from bottom to top - Heating platens: 2 electric platens, with new heating rods - Heating platen dimensions approx.: 600 x 630 mm - Distance between the heating platens approx.: 420 mm - New electric valves - AC machine output oil pump: 5.5 kW - New control cabinet with Siemens 7’ touch panel - PLC control system make Siemens S7-1200 - New cabling - Frequency inverter made by Schneider - Light barriers in the front area, Overhauled in accordance with CE standard safety regulations Operating instructions and maintenance instructions in German Warranty: 1 year The data for this ad was created with ModulMWS ...

New Zig-Zag Cutter! Machine is designed to cut an 800mm Batch into an endless strip for Extruder feeding. 12 month Warranty! Description attached!

machine measurements: 2.100 x 2.200 x 2.100 mm machine weight: 2.000 kg power capacity: 36 kW Condition: used Specification: cleaning and degreasing system FIRBIMATIC LOGICA 200V closed cleaning system for the cleaning of of metallic components with highly stabilised perchloroethylene - second-hand - Closed cleaning system for the cleaning of metallic components components with highly stabilised perchloroethylene. - PER-based cleaning and degreasing system Possible cleaning cycles: 1. pre-cleaning (spraying) 2. main cleaning (spray and flood cleaning) 3. rinsing (hosing down) 4. vapour degreasing 5. vacuum drying - All cleaning cycles are freely programmable. - Filling volumes: Tank 1: 170 litres Tank 2: 80 litres - Type of solvent: Perchloroethylene - Total connected load of motors: 9.65 kW - Installed electrical power incl. heating syst ...

Key data: 2000 mm, 1300 mm

available Berstorff Bias Cutter Angle 0-50 degrees with manual splice 90 degree with automatic splice Ce certified Description attached!

volt: 380 V weight: 1,4 t : The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Cevenini Log Cutter Model M200 1.5m wide x 200 mm diam. Complete with motor

machine measurements: ca. 1030 x 1110 x 1950 mm machine weight: 800 kg power capacity: ca. 2,8 kW Condition: used Specification: SiloStar 924 dosing system - used - For dosing liquid silicone LSR - LSR dosing with servo-hydraulic unit, servo motor 2.8 kW - Dosing with piston pumps - Uniform emptying of components A + B via proportional compensation cylinders - Variable mixing ratio - Touchscreen with visualised user interface - Containers: 200 litre drums - Operation via 10 inch touch display - Automatic mixing material pressure control with sensor directly on the mixing block - Pressure sensor for A + B - Circulation device A + B - Power connection: 380-480 VAC, 50/60 Hz (3P + PE), 16 A - Mixing head machine connection - Hose package 2x nylon DN 16 x 2500 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Blackfriars Rotary Cutter / Granulator Model 12 ASHD/267 With sound booth

UNTHA Shredder Model RS30 Year 10/2023 Hours: 97 Power 22kW 400V/50Hz CE marked In ‘as new’ condition

Press force max.:: 1.000 kN heating plates:: 480 x 520 mm electrically heated:: 210 - 220 °C piston stroke:: ca. 400 mm no. of stages:: 1 Condition: Used, reconditioned Specification: 4-column vulcanising press 480 x 520 mm, used - Clamping force: 100 t - Closing action: bottom-up - Heating plates: 2 electric plates - Two new heating elements - Plate heating temperature: up to approx. 210–220 °C - Heating plate dimensions: 480 x 520 mm - Distance between heating plates approx.: 400 mm (to be determined during refurbishment) - Working height of lower plate: approx. 1,100 mm - AC motor: 5.5 kW (to be determined during refurbishment) - New solenoid valves - New control cabinet with Siemens 7 touch panel Type KTP700 Basic - Siemens S7-1200 PLC system - Schneider frequency converter - One remote maintenance unit - New cabling - Light cur ...

Key data: 3000 kN, 762 mm, 200 °C

Condition: Factory Rebuilt Model: 3000kN BIPEL Press Application: Compression Moulding Mode of Operation: Manual and Semi-Auto Frame structure: Steel plate frame Cylinder type : Double acting Push back cylinder(s) : Pressing force kN: 3000 Pull back force at circuit pressure kN: 300 Operating height mm : 820 Stroke mm : 610 Daylight between Tables mm : 1205 Table size L -R mm : 785 F-B mm : 890 Opening speed mm/sec: 200 Pressing speed mm/sec:  ...

Key data: 3000 kN

Bed Size: Left to Right 785mm 30 1⁄2 in Front to Back 890mm 35 in Daylight Between Tables 1206mm 47 1⁄2 in Daylight Between Heated Platens 841mm 33 1⁄8 in Heated Platen Sizes(Up To) 760mm x 610mm 28″x24″ Max Working Platen Temperature 220°C 428F Main Ram Stroke(Up To) 610mm 24 in Hydraulic Circuit Pressure 210 Bar 3000 PSI Main Ram Pressing Force 305 T 300 Ton Maximum Pummel Diameter 102mm 4 in Closing Speed(Up To) 150mm/s Opening Speed(Up To) 120mm/s

Troester.200mm H/F strainer M/C Number 7175-71 L/D 6.5/1 Roller Feed 350mm. Hinged strainer head with hydraulic clamp. 125KW AC v/s motor. On single bedplate. With controls.

Used rubber extruder make Troester, type GSV 60/k-12-18D-m.S., Execution as desired, with or without vacuum Built in 1991, machine was in operation until the beginning of 2010 Feed roller Kpl. new drive with flat gear motor Screw speed max. 62 rpm. Engine power 22 kW Control with PLC and temperature control new on request Extruder similar to attached photos.