4 DAEWOO cnc turning machines used machines

CNC lathe Daewoo Lynx 200 B CNC Fanuc 21t, 10 tool turret tailstock, bar feeder The machine can be seen under power in our warehouse (M i m u)

DAEWOO LYNX 200B LATHE with FANUC control system

DAEWOO LYNX 200B LATHE with FANUC control system

With documentation and accessories including a two-jaw chuck, diameter: 165 mm, basic tool holders, as well as a collet chuck 173E-42 B. Additional technical specifications: • max. Load: 11,0 kW • Swing diameter over bed: 510 mm • Swing diameter over cross slide: 290 mm • max. turning diameter (recommended): 170 mm • max. turning diameter (technical): 320 mm • travel of X-axis: 400 mm (160 + 15 mm) • travel of Z-axis: 330 [550] mm For further technical data, please refer to the photographed machine specification.

With technical documentation and accessories such as tool holders and a two-jaw as well as a three-jaw chuck, incl. SCHUNK clamping jaws, diameter: 165 mm. Additional technical specifications: • spindle chuck diameter: 169 mm • boring bar diameter: 25 mm • cutting feed X, Z: 0.001 - 500.000 mm/rev

turning diameter: 320 mm turning length: 305 mm control: Fanuc total power requirement: kW weight of the machine ca.: 3500 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

connected load frequency: 230 V battery: 24V / 100Ah Brush diameter: 510 mm turning speeds: 175 U/min 0: Luft 24 L / s tank capacity: 50 / 50 Liter weight: 160 kg range L-W-H: 1,1 x 0,52 x 1,0 mm Daewoo floor cleaning machine: Packed with battery and charger Theoretical surface cleaning: Output: 2000 m²/h Suction width: 850 mm Cleaning width: 510 mm Max. working area incline: 2% Fresh/waste water tank volume: 50/ 50 L The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

DAEWOO PUMA 300 LB (Doosan), 2-axis CNC lathe, CNC Fanuc 18T, Hydraulic tailstock, Condition: very good. This machine can be inspected in our warehouse, under power., Mimu machine tools Italy

Torni CNC, Doosan Puma TW2600, 2016 (low hours), complete with robot, it can be inspected in our warehouse in Gussago BS

turning diameter: 376 mm turning length: 760 mm control: FANUC I-Series Plus greates pass round over bed: 780 mm swing diameter over slide rest: 630 mm max. turning diameter: 376 mm spindle turning speed range: 4000 U/min spindle drive motor: 22 / 15 kW spindle nose: ASA A2-8 spindle bore: 81 mm bar material dia.: 76 mm c-axis: 0,001 ° chucking diameter: 255 mm Number of tools: 12 St. travel -x axis: 260 (72 + 188 ) mm travel -z axis: 830 mm travel -y axis: 105 (+/- 52,5) mm diameter of quill: 100 mm quill stroke: 100 mm tailstock taper MT: MT 5 total power requirement: 41,98 kVA weight of the machine ca.: 6,1 t dimensions of the machine ca.: 4,0 x 2,5 x 2,2 m CNC control FFANUC I-Series Plus - chip conveyor - driventools 5000U/min, 7,5kW - C-axis - hydraulic unit - tailstock - coolant 7 bar - bar loader interface Capto C3 straight chair: 2 Capto C3 90° chair: 1 ER20 Capto chuck: 10 ER ...

Horizontal turning machine manufactured in 1999. This DAEWOO EcoTurn 200 features a reliable Fanuc 18 T control system, ensuring efficient operation. If you are looking to get high-quality turning capabilities, consider the DAEWOO EcoTurn 200 machine we have for sale. Contact us for further details.

Horizontal turning machine manufactured in 2000. This DAEWOO Puma 350 features a reliable Fanuc 18T control system, ensuring efficient operation. If you are looking to get high-quality turning capabilities, consider the DAEWOO Puma 350 machine we have for sale. Contact us for further details.

This 3-axis DAEWOO PUMA 400MB was manufactured in 2002. It features a maximum machining diameter of 460 mm and a maximum machining length of 1,050 mm. The machine is equipped with a spindle speed range of 30–3,000 rpm and a tool turret with 12 stations. If you are looking to get high-quality CNC turning and milling capabilities, consider the DAEWOO PUMA 400MB machine we have for sale. Contact us for further details.

CNC lathe, year 2003, CNC i Series. Used machine. More info & price on IndustrialBuyer.

CNC lathe, year 2006, CNC 21i-TB. Used machine. More info & price on IndustrialBuyer.

DAEWOO MARINE ENGINE V180 TI + GEARBOX 1800 RPM 600 HP

DAEWOO/DOOSAN MARINE ENGINE V 158 TI V type, direct- injection, water cooled with wet turbo charger & inter-cooler

rated capacity: 8,1 kVA voltage: 400 / 230 V frequency: 50 Hz tank capacity: 15 l engine output: 11 / 15 KW / PS weight of the machine ca.: 0,165 t dimensions of the machine ca.: 0,88 x 0,56 x 0,76 m Diesel generator with: - equipped with electric start. - Equipped with automatic voltage regulator. - Air cooled - Mobile. - Direct injection - Low oil level alarm with auto-stop function. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Brand Daewoo Model: DDAE10500DSE-3G Year of construction: 2022, New Capacitance (KvA) 8.1 kVa (230v) / 7.5 kVa (400v) Engine brand Daewoo Engine model 500 Motor capacity (Kw) 15 Hp Fuel Diesel Voltage 230-400 Frequency (Hz) 50 Dimensions LxWxH (mm) 880 x 560 x 720 Weight (Kg) ca 165 Number of stucco in stock 100+ Comments Max power: 8.1 kVA (400 V) 7.3 kVA (230 V) Rated power: 7.5 kVA (400 V) 6.7 kVA (230 V) Engine Power: 15hp Displacement: 498 cc Fuel tank capacity: 15 L Oil tank capacity: 1.65 L Run time 50% load: 12 hrs Power factor: 1.25 Socket: 1 x 16 A - 1 x 32 A Output 12V: ✓ Battery: 36 AH Noise level at 7M: 72 - 74 dBA Net weight: 165 kg Dimensions: 880 x 560 x 720

rated capacity: max. 8,1 kVA capacity in kVA: bei 400 V - 7,5 kVA rated capacity: bei 230 V - 6,1 kVA power fuel: Diesel 0 tank capacity: 15 l 0: 11 KW cubic capacity: 498 ccm weight of the machine ca.: 165 KG dimensions of the machine ca.: 0,8 x 0,65 x 0,75 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Vertical machining center Daewoo (Doosan) ACE VC500 The machine can be seen working in our warehouse in Gussago BS. Mimu Machine Tools Gussago BS Italy, Vertical machining center - 2-pallet, Daewoo ACE VC500, CNC Model Fanuc, CNC version 18-M, Spindle Taper toolholders iso 40, Power spindle 15 Kw, RPM 10000, Number of tools 30, X-axis travel 760 mm, Y-axis travel 510 mm, Z-axis travel 570 mm, Changer pallet yes, Pallet dimensions 860x560 mm, Maximum load allowed 300 Kg, Swing type pallet yes, High coolant pressure yes, Cheap conveyor yes, Brand Daewoo, Model ACE VC500, Construction year 2000, DIMENSIONS AND WEIGHT, Length 3600 mm, Width 3700 mm, Height 2935 mm, Weight 9200 Kg The machining center is a machine tool equipped with numerical control capable of performing multiple mechanical operations with a single set-up on multiple surfaces of the same work piece. It is generally equipped  ...

This 4-Axis Daewoo ACE-HP 4000 horizontal machining centre was manufactured in 2006, controlled by a FANUC Series 18i-MB system. It features comprehensive travel dimensions: 600mm in X, 560mm in Y, and 565mm in Z, along with table rotation capability. The machine is equipped with spindle cooling, a chip conveyor, and external workpiece cooling, ensuring optimal operation. A robust choice for precision machining, it combines extensive operating hours with dependable performance. Reach out for further details regarding this horizontal machining centre.

This 5-axis DAEWOO PUMA 2000 SY turn-mill centre was manufactured in 2003. It features a max turning diameter of 330 mm, length of 510 mm, and rapid feeds up to 24,000 mm/min. Includes main and sub-spindle capabilities, both with C-axis, and a 12-station turret with live tooling. Consider the opportunity to buy this DAEWOO PUMA 2000 SY turn-mill centre. Contact us for more information about this machine.

This 3-axis DAEWOO ACE V 600 was manufactured in 1997. It features an impressive X-axis travel of 1,260 mm, Y-axis travel of 650 mm, and Z-axis travel of 560 mm. The machine includes a robust table size of 1,400 x 700 mm and a maximum table load of 1,200 kg. If you are looking to get high-quality machining capabilities, consider the DAEWOO ACE V 600 vertical machining centre we have for sale. Contact us for further details.

Loading utility: 500 Liter weight: 0,3 t dimensions: 1750 x 730 x 1080 m Electric tipper - Operating time with a fully charged battery: 8-10 hours - Battery charging time: 6-7 hours - Hydraulic tipping The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.