used Longitudinal cutting machines for sale

12″ x .125″ x 4000Lb Bliss Slitting Line Make: Bliss Material Width: .075” – 12” Material Thickness: .008” – .125” Weight Capacity: 4,000Lb Coil ID: 16” – 20” Coil OD: 72”

72”x 0.5” x 60,000Lb Braner Turret Type Loop Slitting Liney Braner Turret Type Loop Slitting Line is used for coil metal cross cutting with maximum width 72”, maximum 0,5” metal thcikness and 60,000Lb coil capacity Make: Braner Year New: 1996 Material Thickness: .060″ – .500″ Material Width: 12″ – 72″ Coil Weight: 60,000Lb Line Speed: 120 – 250 feet per minute Coil ID: 20″ – 24″ Coil OD: 75″ Slitting Cap: .500″ / 4 cuts – .125″ / 40 cuts Entry L-Type Coil Car Hydraulic Lift & Traverse Self Contained Hydraulics Control Panel Mandrel Uncoiler Powered Hold – Down Roll Outboard Bearing Support Hydraulic Feed-Up Drive Water Cooled Brake Hydraulic Peeling Table Driven Entry Pinch Rolls Adjustable Edge Guides Entry Mechanical Crop Shear Two Turret Type Slitting Heads Arbor Diameter: 12″ Powered Arbor Adjustment Powered Head Rotation Motor: 100HP DC Driv ...

CINCINNATI ACW6 slitting line is used in the processing of thin steel sheets with a maximum thickness of 4 mm. The process consists in gradually unrolling the sheet coils towards cutting rollers with special roller knives with a thickness of 5 to 30 mm, and then passing the sheet between the rollers for precise slitting. After the slitting process, the sheet is wound onto coils ready for further processing. The ACW6 slitting line guarantees the highest product quality while making optimum use of the raw material. The CINCINNATI coil slitting line consists of: – sheet decoiler – sheet metal winder – roller knives (thickness 5 mm, 10 mm, 12 mm, 20 mm, 25 mm, 30 mm) – ejector spacers (width 10 mm, 12 mm, 20 mm, 25 mm, 30 mm) – slitting aggregate unit – brake Technical specifications of the CINCINNATI ACW6 slitting line - maximum sheet thickness: 4 mm - minimum shee ...

60″ x .135″ x 20,000Lb Cincinnati – Forte Loop Slitting Line Material Width: 12″ – 60″ , Thickness: .010″ – .135″, Weight: 20,000Lb, Coil ID: 16″ – 24″, Coil OD: 72″, Speed: 600 fpm, Direction: Left to Right. Entry Turnstile, Entry L-Type Coil Car, Mandrel Uncoiler with Hold-Down Roll, Powered Peeler, Driven Pinch Rolls, PVC Applicator, Entry Shear, Two Slitting Heads, Injection Design, 5″ & 7″ Arbor Diameter, 75HP DC Motor, Two (2) Hydraulic Scrap Winders, Pit Cross Over Table, Drag Board & Rotary Tension Stand, Recoiler with Over-Arm Separator & Push-Off, 150HP DC Motor, Exit L-Type Coil Car & Turnstile. Electrics, Hydraulics, Controls, Tooling, Spare Parts

Power: 100 kWX - axis: 300 mmY - axis: 400 mmNumber laser heads: 0  CNC Brand: _Unknown / OtherCNC Model: Lasersoft 3 D Make Deckel Maho Type DML 40 S Year 2001 LASERSOFT 3D - 6 Axis Table length (mm)L = 400 Table width (mm)W = 300 Longitudinal X (mm)X = 300 Cross Y (mm)Y = 400 Vertical Z (mm)Z = 500 Laser 100 W3 Mechanical axis 3 Optical Axis- Automatic repositioning - DECKEL MAHO LASERSOFT 3 D - Direct 3 D Autocad import - Filigran Kavitaeten 0.04 mm - Keramik machining possible - Vertical machining possible - Dimensions - Length : 3.500 - Width : 3.000 - Height : 2.000 - Weight : 2.200

EAGLE eVision 1530 F3.0 AF fiber laser was manufactured in 2012 in Poland. The machine used in the cutting process of workpieces made of structural steel, stainless steel, aluminium and copper, guarantees the user excellent dimensional and shape precision during the cutting process. The low cutting edge and small heat-affected zone ensure that the geometry of the workpiece does not change during processing at the edges of the material. The EAGLE fibre laser uses the energy-efficient and trouble-free IPG YLS-3000 laser source to supply the PRECITEC cutting head with a high-quality 3 kW laser beam. The cutting head is equipped with overload and collision protection, which automatically shuts down all machine axis drives if a collision with the workpiece is detected. Thanks to the special head positioning system (HRS), a constant distance is maintained between the head and the sheet meta ...

Slitting line Fimi 1500×2.5mm x15t (A3783) Manufacture FIMI ITALY Year 1990 Strip width Min. 200 mm Max. 1500 mm Strip thickness 0.3 – 2.5 mm Coil weight Max. 15 t Coil- Max. 1500 mm Speed Max. 80 m/min Working direction Right  Left The line consists of:  Decoiler Mandrel Cone-Ø 480 – 610 mm Drive / braking Hydraulic motor Lifting table Hydraulic  Coil opener / pinch roll unit Telescopic table Hydraulic No. of pinch rolls 2 Pinch roll-Ø 400 mm Driving motor 25 kw  Slitting head No. of heads 2 Shafts diameter 120 mm Main drive D.C. motor Driving power 92 kW  Scrap baller  Minimum scrap width 5 mm  Maximum number of slits 17 Slits up to 1.0 mm 5 Slits at 2.5 mm  Brakes Pneumatic Press up and dow  Re coiler Capacity 15 t Diameter 508 mm Driving power 120 kw  Term style 4 arms x 15 ton

Cut-to length slitting machine SM-1250х8 Cut-to-length slitting machine is used for longitudinal cutting of the metal sheets with maximum thickness 1mm, aluminum composite panels, paper, polycarbonate thanks to special cutting knives that are fixed on rolls of the slitting machine. This cut-to-length slitting machine lets you to cut the material into eight strips. The diameter of the rolls is 56 mm There are four types of the sheet metal cut-to-length machines we make: The manual cut-to-length slitting machine (cutting for 2 strips) The electric cut-to-length slitting machine (cutting for 3-4 strips) The electric cut-to-length slitting machine (cutting for 6-10 strips) The electric cut-to-length slitting machine (cutting for 12-20 strips) The operator of cut-to-length slitting machine can easily change the width of the strips and their numbers. There are special scr ...

18″ x .070″ x 6,000Lb Morvay Slitting Line Material Width: 18″, Weight Capacity: 6,000Lb, Material Thickness: .008″-.070″, Coil ID: 20″, Direction: Left to Right. Mandrel Uncoiler with Disc Brake, Powered Mandrel Expansion, Powered Hold-Down Roll, Driven Entry Pinch Rolls, Slitting Head with Adjustable Arbors, Knives & Tooling, Recoiler with Hydraulic Push-Off, Powered Over-Arm Separator, 50HP Motor, Exit 2-Arm Turnstile

Paxson Loop Slitting Line 72″ x 0.375″ x 50,000Lb (A3754) Make: Paxson Material Width: 12″ – 72″ Weight Capacity: 50,000Lb Thickness: .050″ – .375″ Coil ID: 20″ – 30″ Coil OD: 72″ Line Speed: 850 feet per minute Direction: Right to Left Entry L-Type Coil Car Floor Standing Design Hydraulic Lift & Traverse Self Contained Hydraulics Mandrel Uncoiler Powered Hold-Down Roll Hydraulic Expansion Water Cooled Brake Feed-Up Motor Sliding Base Hydraulic Peeling Table Driven Pinch Rolls Adjustable Edge Guides 4-Roll Coil Breaker Mechanical Entry Crop Shear Two (2) Slitting Heads Arbor Diameter: 9″ and 12″ Crane Removable Type Adjustable Arbors 150HP DC Motor Drive Multi Speed Gear Lots of Knives and Tooling Two Pro-Eco Scrap Winders Max Thickness: .500″ 25HP Motor for Each Unit Powered Open / Close Pit Cross Over Table Drag Bo ...

72″ x .187″ x 50000Lb Paxson Loop Slitting Line Make: Paxson Material Width: 12″ – 72″ (Uncoiler 60″) Material Width: .010″ – .187″ Coil Weight: 50,000Lb Coil ID: 20″ – 24″ Coil OD: 72″ Speed: 500 /1000 fpm Direction: Right to Left Material Strength: 40,000 yield / 50,000 psi shear Material: CR, HR, Galvanized Entry Transfer Cart Entry Coil Car Mandrel Uncoiler Powered Hold-Down Roll Powered Expansion Sliding Base Hydraulic Peeling Table Driven Pinch Rolls

Slitting line Pro-Eco 72″ x .250″ x 74,000Lb (A3774) Slitting line Pro-Eco 72″ x .250″ x 74,000Lb (A3774) is perfect solution for longitudinal cutting of coil metal into strips. This line can work with very big coils up to 74,000 Lb weight and 0.25 inches maximum metal thickness. Line is strong enough to make cutting speed 200 – 600 fpm depends on metal thickness and width you work with Slitting line Pro-Eco 72″ x .250″ x 74,000Lb (A3774) Manufacturer: PRO ECO Material: CRS, HRS, HPP & O Material Width: 12″ – 72″ Material Thickness: .060″ – .250″ Coil Weight: 74,000Lb Coil ID: 20″ – 30″ / 20″ – 24″ Coil OD: 72″ Line Speed: 200 – 600 fpm Direction: L-R Three (3) Coil Storage Ramp Coil Car Powered Lift & Traverse Double Cone Uncoiler Sliding Base Dual Water Cooled Brake Feed-Up Motor Powered  ...

SAF PLASMATOME 25 plasma cutting machine was built in 2000 in France. The machine, characterised by its rigid and robust design, is designed for precision cutting of sheet metal with a thickness of up to 45 mm. Thanks to the use of double drives on the longitudinal axis, high working speeds are obtained, which result in high quality and accuracy of machining. Workpieces are machined under a water sheet on a large work table measuring (L x W) 6000 mm x 2000 mm, using a cutting head powered by a powerful KJELLBERG PA-S45 W plasma source. The SAF AIR LIQUIDE PLASMATOME 25 plasma cutting machine is controlled by a control panel equipped with a multi-tasking CNC controller DIGISAF, allowing full control of the machine operation. Technical specifications of the SAF PLASMATOME 25 plasma cutting machine - CNC controller: DIGISAF - plasma source: KJELLBERG PA-S45 W - work table surface a ...

Slitting line HJ Loop 1600mm x 9mm x 50,000Lb (A3790) for longitudinal cutting of coil metal into strips of required width up to 9mm metal thickness Year of Manufacture: 2002 Make: HJ ENG,KOREA Raw Material: HR Coil Tensile Strength: Max. 50Kg/mm2 Yield Strength: Max. 30Kg/mm2 Coil Thickness: Min. 1.2mm ~ Max. 9.5mmT Coil Width: Min. 400mm ~ Max. 1,650mm Coil Weight: Max. 25,000Kg Coil Inside Diameter: 508mm Coil Outside Diameter: Min. ∅1,000mm ~ Max. ∅2,000mm LINE DATA Line Speed: Max. 150/80m/min Threading Speed: Max. 20m/min Slitting System: Pull & Drive Cutting by DC Power Control Slitting Width: Min. 40mm ~ Max. 1,300mm Slitting Number: Max. 30Cuts x 29Strips Pass Line Height: 900mm Line Threading Direction: Left To Right Coil Car With Coil Skid Uncoiler Coil Peeler Coil Opener Three(3) Bending Roll No.1 Pinch Roll Crop Shear with Guide Table Si ...

Slitting line SECO 60″ x 0.375″ x 50,000Lb (A3791) is perfect solution for longitudinal coil metal cutting into strips with maximum metal thickness 0.375” and maximum coil width 60” Cold Rolled and Hot Rolled Steel 18-60” Strip Width 2 Speed Gear Box 200-500 FPM Thickness: .032″-.375” Complete Line with the Following Components: L-Type Entry Coil Car 40,000# Max Coil Weight Uncoiler: Coil ID: 23-30.50” Coil OD: 72” Maximum Coil Weight: 40,000# Maximum Sliding Base Hydraulic Expansion Peeler and Hold Down Roll 5 Roll Coil Breaker Entry Adjustable Edge Guides Entry Crop Shear Slitting Head: 10” Arbors 40 HP Motor Drive 2 Scrap Winders Recoiler: Coil OD: 72” Max Coil ID: 24” 150HP DC Motor 3 Arm Exit Turnstile 40,000# per Arm Motorized Turn Complete Line with Knives, Rubbers, and Spacers Controls, Hydraulics, and  ...

STEP-MET NCW 1250 X 1.5 slitting line built in Poland in 2011, is used in the process of slitting thin steel sheets with a maximum thickness of 1.5 mm into equal-sized stripes. The material is slit longitudinally by high-quality cutting rollers, which guarantee the highest product quality while making optimum use of the raw material. The NCW 1250 X 1.5 slitting line consists of several modules, including, among others, an easy-to-operate control cabinet that allows adjustment of the operating speed and cutting width. The STEP-MET slitting line consists of the following components: – sheet metal decoiler – sheet metal winder – control cabinet Technical data of the STEP-MET NCW 1250 X 1.5 slitting line - maximum sheet metal thickness: 1.5 mm - maximum sheet metal width: 1250 mm - minimum sheet metal width: 25 mm - maximum sheet metal coil weight: 6 t - cutting speed ran ...

TRUMPF TruLaser 3030 fiber laser built in Germany in 2013, is used for precision machining of workpieces made of structural steel, stainless steel, as well as brass and copper, thanks to special technology data packages equipped in the machine. The extremely efficient and reliable fibre-cutting technology expands the machining possibilities and allows to achieve very smooth and even edges. The laser cutting machine features a robust, durable design that prevents any vibrations from occurring during changes in direction. The enclosed laser body with lift-up roof and fixed guards effectively protect the operator during work. The axes are driven by a direct Torque drive (X-axis) and direct linear drives (Y-axis and Z-axis), which, combined with hardened guideways of the highest manufacture precision, ensure that high accelerations and working speeds are achieved. Generated by the reli ...

Universal Slitting Line 72″ x .187″ x 20,000Lb Material Width: 12″ – 72″ Material Thickness: .015″ – .187″ Coil Weight: 20,000Lb Coil ID: 20″ Coil OD: 72″ Direction: Left to Right Entry Floor Standing Coil Car L-Type Design Hydraulic Lift & Traverse Mandrel Uncoiler Powered Hold-Down Roll Hydraulic Expansion Air Cooling Brake Sliding Base Hydraulic Peeling Table Slitting Head Arbor Diameter: 7″ Powered Arbor Adjustment 100HP DC Motor Knives & Tooling Recoiler Powered Push-Off Hydraulic Over-Arm Separator Hydraulic Expansion 100HP DC Motor Exit 2-Arm Turnstile Arm Width: 72″ Powered Rotation Complete Slitter with Electrics, Hydraulics, Controls, Tooling

60″ x .135″ x 40,000Lbs Yoder Slitting Line Material Width: 12″ – 60″ Material Thickness: .010″ – .135″ Weight Capacity: 40,000Lbs Coil ID: 20″-24″ Coil OD: 72″ Pull Through Design Entry Coil Car Mandrel Uncoiler with Hold-Down Roll Hydraulic Peeler Driven Pinch Rolls Slitting Head with Gear Box and AC Feed-Up Motor Single Scrap Winder Recoiler with Over-Arm Separator DC Motor Drive Exit Turnstile Electrics, Hydraulics, Controls