NILES dlz used machines

Parallel Lathe WMW NILES type DLZ 500 IV L 1000 Between points: 1000 mm Maxi Ø on bench: 500 mm Maxi Ø over saddle: 300 mm Spindle diameter: Ø 50 mm Spindle speed: from 28 to 1400 RPM 3-jaws chuck Ø 200 mm Threadings: Metric + Whitworth Tailstock CM4 Auto Feeds transverse + longitudinal + rapid Lubricant pump Voltage: 380 V Dimensions (L x W x H): 3000 x 1400 x 1500 mm Weight: approx 2,5 T

turning diameter over bed: 500 mm turning diameter over slide rest: 330 mm turning diameter in the gap: 600 mm turning length: 3000 mm bed width: 505 mm spindle bore: 72 mm spindle head: DIN 55022 Gr. 8 taper in tailstock: MK 5 turning speed range: 22,4- 1120 U/min power requirement: 18,5 kW dimensions: 5,3 x 1,75 x 1,53 m weight of the machine ca.: 5,2 t used lathe in nice condition with digital scale - 2 axis digital scale - 4 jaw chuck Ø 250 mm - 3 jaw chuck Ø 260 mm - Multifix C toolholder system - some toolholders - steady The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. wheel diameter: 2000 mm gear width: . mm max. module: 22 max. hob diameter: 250 mm hob turning speeds: 16-92 U/min total power requirement: 13 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 1650 mm turning diameter over slide rest: 1200 mm turning length: 7500 mm turning dia. in gap: 2500 mm spindle diameter: 105 mm speed: 3,55 - 180 (x24) U/min voltage: 380 V total power requirement: 45 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

centre distance: 5000 mm turning diameter over bed: 4000 mm turning dia. in gap: 5000 mm spindle bore: 104 mm turning speeds: 1,4 - 71 (18x) U/min total power requirement: 30 kW weight of the machine ca.: t dimensions of the machine ca.: m 4-jaw face plate Ø 3.150 mm modular lathe! The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Face plate diameter: 1.250mm Center height above foundation slab: 1,250mm Weight: 19t Power: 55Kw Max. torque on the face plate: 31,500Nm Maximum workpiece mass between centres: 16,000 kg Speed range: 2.24 – 224 rpm

Face plate diameter: 1.250mm Center height above foundation slab: 1,250mm Weight: 19t Power: 55Kw Max. torque on the face plate: 31,500Nm Maximum workpiece mass between centres: 16,000 kg Speed range: 2.24 – 224 rpm

turning diameter: . mm turning length: 2000 mm control: Siemens 840 D sl mainspindle: turning speed max.: 3800 1/min mainspindle: torque max.: 1200 Nm tailstock:: diameter of quill: 140 mm center point: MK6 quill power: 5 - 30 kN feed rate Z-axis: 0,1 - 30000 mm/min rapid traverse Z-axis: 40 m/min feed rate X-axis: 0,1 - 18000 mm/min rapid traverse X-axis: 25 m/min total power requirement: 125 kW weight of the machine ca.: 20 t The machine can still be inspected under power at the production plant. The condition of the machine is good, the accuracy during turning operation is very good. The milling drive is not functional. A quotation from Niles for the repair of the milling drive is available on request. Including hydraulic steady rest. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter: . mm turning length: 2000 mm control: Siemens 840 D sl mainspindle: turning speed max.: 3800 1/min mainspindle: torque max.: 1200 Nm tailstock:: diameter of quill: 140 mm center point: MK6 quill power: 5 - 30 kN feed rate Z-axis: 0,1 - 30000 mm/min rapid traverse Z-axis: 40 m/min feed rate X-axis: 0,1 - 18000 mm/min rapid traverse X-axis: 25 m/min total power requirement: 125 kW weight of the machine ca.: 20 t The machine can still be inspected under power at the production plant. The condition of the machine is good, the accuracy during turning operation is very good. The milling drive is not functional. A quotation from Niles for the repair of the milling drive is available on request. Including hydraulic steady rest. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter: . mm turning length: 2000 mm control: Siemens 840 D sl mainspindle: turning speed max.: 3800 1/min mainspindle: torque max.: 1200 Nm tailstock:: diameter of quill: 140 mm center point: MK6 quill power: 5 - 30 kN feed rate Z-axis: 0,1 - 30000 mm/min rapid traverse Z-axis: 40 m/min feed rate X-axis: 0,1 - 18000 mm/min rapid traverse X-axis: 25 m/min total power requirement: 125 kW weight of the machine ca.: 20 t The machine can still be inspected under power at the production plant. The condition of the machine is good, the accuracy during turning operation is very good. The milling drive is not functional. A quotation from Niles for the repair of the milling drive is available on request. Including hydraulic steady rest. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

overhauled: 2007 Control Siemens ... Sinumerik 840 D Max. workpiece diameter ... 2500mm Table diameter ... 2240mm Max. workpiece height ... 1250mm Axis Z ... 1000mm Max. workpiece weight ... 10000 kg Main engine power ... 55kW L x W x H 7000x4400x5500mm Machine weight ... 37900kg The machine is in good condition. More info on request.

overhauled: 2007 Control Siemens ... Sinumerik 840 D Max. workpiece diameter ... 2500mm Table diameter ... 2240mm Max. workpiece height ... 1250mm Axis Z ... 1000mm Max. workpiece weight ... 10000 kg Main engine power ... 55kW L x W x H 7000x4400x5500mm Machine weight ... 37900kg The machine is in good condition. More info on request.

faceplate diameter: 3500 mm swing diameter: 4000 mm turning height: 3150 mm slide adjustment: 1700 mm table load: 25 t turning speeds: U/min Feed: mm/U digital readout: Heidenhain Rest: 2 Side head: total power requirement: 90 kW weight of the machine ca.: 95 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

faceplate diameter: 5300 mm swing diameter: 6300 mm turning height: 2800 mm slide adjustment: 1700 mm table load: 50 t turning speeds: 0,3-14 U/min Feed: 0,056-10 mm/U digital readout: Sony Rest: 2 Side head: chip conveyor: total power requirement: 120 kW weight of the machine ca.: 187 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 1650 mm turning diameter over slide rest: 1200 mm turning length: 7500 mm turning dia. in gap: 2500 mm spindle diameter: 105 mm speed: 3,55 - 180 (x24) U/min voltage: 380 V total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 4000 mm turning diameter over slide rest: . mm turning length: 5000 mm total power requirement: 30 kW weight of the machine ca.: . t dimensions of the machine ca.: . m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 4000 mm turning diameter over slide rest: . mm turning length: 5000 mm total power requirement: 30 kW weight of the machine ca.: . t dimensions of the machine ca.: . m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

3-jaw chuck, three-jaw chuck WMW DH-B 200x3x6 ( DH-B200x3x6 ) TGL 30-2332 Outer Ø: 200 mm Bolt circle Ø : 133.5 mm Bore Ø: 54 mm Height with jaws: 140 mm used, tested ! Dimensions: 200 x 200 x 121 mm

turning diameter over bed: 2000 mm turning diameter over slide rest: 1600 mm turning length: 10000 mm control: FANUC 0i TF workpiece weight: 25 t steady: 4 feed: 1 - 3000 mm/min main drive: 60 kW main spindle speeds:: 1,5 - 160 U/min bed width: 1150 mm faceplate: 1600 mm tail stock: tailstock quill diameter: 260 mm total power requirement: 110 kW weight of the machine ca.: 120 t the machine is currently being overhauled and equipped with - new electrics (Siemens, Schneider, cabinet) - CNC control FANUC 0i TF - new Fanuc motors - new hydraulic parts - complete mechanical overhaul - Ball screw (B-axis) - bed overhaul - three-track bed - Grinding device 1500 rpm - Milling Unit - Face plate with 4 jaws - 3 steady rests - incl 1 year warranty from overhauler on electrical and hydraulic components and 2 years on FANUC CNC Completion of overhaul after order (approx. 2 months) The data for th ...

3- Jaw Chuck WMW NILES DHK 200x3 Outer Ø: 200 mm Flange: 155 mm Bore Ø: 60 mm Bolt circle: 175 mm Height with jaws: 125 mm Chuck number: 507 Dimensions: 200 x 200 x 125 mm

3- Jaw Chuck WMW NILES DHK 200x3 Outer Ø: 200 mm Flange: 155 mm Bore Ø: 60 mm Bolt circle: 175 mm Height with jaws: 125 mm Chuck number: 507 Dimensions: 200 x 200 x 125 mm

With two machining modules, X-axis: -50 to 725mm, Y-axis: -200 to 300 / -250 to 250mm, rapid traverse X-, Y-, Z-axis: 18/12/30m/min, control: Siemens Sinumerik, temperature range: 5–40°C, power type/frequency: 3 PEN / 50Hz, rated voltage: AC 400V, control voltage: DC 24V, auxiliary voltage: AC 230V, connected load: 102kVA, rated current: 148A, rated current (fast): 148A, fuse (slow): 160A, length: 8000mm, width: 3000mm, height: 4000mm, weight: approx. 17t, operating hours: approx. 80,000h. The machine is fully functional, the ball screw drive (recirculating spindle) of the Z-axis was renewed in 2024 and it has been regularly maintained. Comes with documentation, control cabinet, hydraulic unit, filter elements, and chip conveyor. An on-site inspection is possible.

max. width of grinding wheel: 50 mm ratio: 0 max. dia. of grinding wheel: 400 mm total power requirement: 3 kW weight of the machine ca.: 1000 kg dimensions of the machine ca.: m Pre-Dressing Device for Gear Grinding Wheels The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning length: 2500 mm control: Sinumerik 840 D spindle head: A 11 tool numbers: 48 swing diameter over bed slide: 750 mm swing over bed: 780 mm c-axis: 0,1-30 1/min diameter of quill: 160 mm taper bore: MK 5 tool length - max.: 500 mm weight of tools max.: 15 kg weight of the machine ca.: 27 t dimensions of the machine ca.: 8,4 x 4,0 x 2,5 m Technical details: Nominal turning length: 2,500 mm Swing diameter over bed slide: 750 mm Swing diameter over bed: 780 mm Working height: 1,300 mm Spindle head to DIN 55026: A 11 Bore through: 123 mm Diameter in front bearing: 200 mm Oriented spindle stop: 0-359 degrees Drive power at 100/60 % duty cycle: 37/45 kW Total speed range: 10-2,500 1/min Number of speed ranges: 2 Speed range I: 10-775 1/min Speed range II: 20-2,500 1/min Max. torque at 60 % duty cycle: 2,500 rpm. Torque at 60 % ED: 2,083 Nm (up to 186 rpm) The data for this ad was crea ...

max. wheel diameter: 630 mm gear width: 215 mm max. module: 12 min. module: 1 number of teeth: 5 - 140 stroke length max.: 225 mm table diameter: 500 mm table load: 400 kp grinding wheel diam. min/max.: 270-350 mm max.helical angle: 45 ° no. of strokes: 75 - 315 p.M. total power requirement: 8,5 kW weight of the machine ca.: 6,3 t dimensions of the machine ca.: 3,2 x 3,6 x 3,7 m change gears, program control, complete covering, coolant/Filtering attachment The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.