PAAL ke used machines

used chain conveyor belt Manufacturer: PAAL Type: KEL 1000 Year of construction: 1997 specifications: Conveying width: approx. 1,000 mm Center distance:approx. 7,500 mm Band course: ascending over the entire length, Conveyor belt drive power: 3.0 kW Side bolster height: 500 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE

Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1500 Year of construction: 2008 specifications: Conveyor width: approx. 1,500 mm Wheelbase:approx. 9,625 mm Strip course: approx. 2,935 mm horizontally underfloor, then rising to a length of approx. 4,500 mm below 28°, sloping below 10° on the remaining length and conveying into the press Conveyor belt speed: 0.27 m/sec Conveyor belt drive power: 4.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 777 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE as far as possible pre-assembled, consisting of: - Strip scaffolding in solidly welded section steel and sheet steel edge construction, - additional sliding guides underneath the belt support profiles in the horizontal and climbing sections to support heavy loads, - Conveyor belt (quality: EP 200/2 2:1) with 2 ...

Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1500 Year of Make: 2009 specifications: Conveying width: approx. 1,500 mm Center distance: approx. 9,625 mm Belt course: approx. 3,000 mm horizontally running underfloor, then rising below 30° over a length of approx. 5,875 mm, sloping below 20° on the remaining length and conveying into the press Conveyor belt drive power: 3.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 777 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt with 20 mm high T-studs on the sides to seal the belt stringers,  ...

Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1750 Year of Make: 2004 specifications: Conveying width: approx. 1,500 mm Belt run: approx. 4,300 mm horizontally underfloor, then increasing over a length of approx. 6,300 mm, Conveyor belt drive power: 4.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 1,027 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt with 20 mm high T-studs on the sides to seal the belt stringers, - Belt routing in a neutral zone to avoid stretching tensions, - Chain type M-80 with case-hardened bushings, bolts and roller ...

Used Chain Conveyor Belt Manufacturer: PAAL Type: KEM 1500 Year of Make: 2005 specifications: Conveying width: approx. 1,500 mm Belt run: approx. 3,100 mm horizontally underfloor, then rising below 28° over a length of approx. 6,000 mm, Descending below 10° on the remaining length and conveying into the press Conveyor belt speed: 0.27 m/sec. Conveyor belt drive power: 4.0 kW Sidewall heights - in the horizontal part: 527 mm - in the climbing section: 777 mm Operating voltage: 3 x 400 VAC / 50 Hz / N / PE pre-assembled as far as possible, consisting of: - Strip frame in solidly welded profile steel and sheet steel edge construction, - Additional sliding guides below the belt support profiles in the horizontal and riser sections to absorb heavy loads, - Conveyor belt (quality: EP 200/2 2:1) with lateral 20 mm high T-studs for sealing the be ...

Baler Paal Konti 200 D, built in 2000, optionally with matching conveyor belt Paal KEM-1400 Technical data: Manufacturer: Paal Type Paal Konti 200 D Year of construction 2000 Hours: 28155 Pressing force 60 t Drive power 45 kW Total connection 60 kW Filling opening 1020 x 1400 mm Bale dimensions 750 x 1100 mm, length variable 4-fold automatic tying throughput at 35 kg/m³ approx. 9.5 t/h 60 kg/m³ approx. 16.5 t/h 100 kg/m³ approx. 26 t/h Bale weight 450 to 650 kg Transport dimensions approx. 10123 x 2152 x 2720 mm (LxWxH) Machine weight approx. 15,000 kg Materials: paper, cardboard, foil The press is in good condition and has been inspected and tested. You can find a video on our website or YouTube channel. The complete documentation is available. Please note: All technical data refer to the manufacturer's specifications. We a ...

Baler Paal Konti 325 D/SO, built in 1999 Technical data: Manufacturer: Paal Type Paal Konti 325 D/SO Built in 1999 Hours: 50702 Press force 94 t Drive power: 2 x 45 kW Total connection 104 kW Filling opening 1020 x 1750 mm Bale dimensions 750 x 1100 mm, length variable 4-fold automatic tying Throughput at 35 kg/m³ approx. 14 t/h 60 kg/m³ approx. 24 t/h 100 kg/m³ approx. 38 t/h Bale weight 525 to 800 kg Transport dimensions approx. 12352 x 2340 x 2800 mm (LxWxH) Machine weight approx. 28,000 kg Materials: paper, cardboard, light waste, plastic waste Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or any errors. The offer is subject to change, subject to prior sale and can be revoked at any time. Visits are possible by arrangement. The sale against advance payment is made ex wor ...

Control cabinet for PAAL accounts 200, 275, 325, 425, 500, 600, 700 after renovation An original control cabinet, the one from the PAAL Konti 425 B/K, built in 1992, with the cross binding. It is based on SIEMENS S5 controller. It is also suitable for the other models such as: Konti 200, 275, 325, 425, 500, 600, 700, depending on model and drive power, also for the variant with the cross binding. A complete control cabinet, functional, after renovation We have several channel balers and balers in our warehouse and we cordially invite you to contact us!

Dual hydraulic pump for PAAL, 45kW Used 2-piece hydraulic pump for PAAL channel baling press. Can be used in systems with a 45 kW motor

Baler Paal Pacomat II with hopper, built in 1979 Specifications: Manufacturer: Paal Type: Pacomat II Year of Make: 1979 Drive power: 11 kW Pressing force: 27 t Channel cross-section: 700 x 1000 mm Filling opening: 1000 x 650 mm Flow rate: approx. 60/115 m³/h Bale size: 700 x 1000 mm Bale weight: up to 400 kg Machine dimensions: approx. 7000 x 2000 x 2000 mm (LxWxH) Machine weight: approx. 5200 kg Materials: paper, cardboard, foil Remarks: The machine is in working condition. It was inspected and tested by us in 28816 Stuhr. You can find the video on our website or our Youtube channel. Viewings, also under power, are possible at any time by arrangement. On request, we also carry out tests with your material for an expense allowance. We will also be happy to answer any questions you may have about the machine by phone from Monday to Thursday from 08.00 to 14.00 ...

automatic baling press Manufacturer: PAAL Type: KONTI 275 F Built: 2007 Main parts of the press: 1 automatic duct press (without wire winding devices) 1 automatic lacing 1 Hydraulic system 1 Electric control technical data: Pressing force: 800 kN / 80 t at 300 bar Specific pressing force: 9.70 kg/cm2 Channel cross-section (h x w): 750 x 1,100 mm Filling opening: 1,020 x 1,600mm Number of connecting wires: 4 pieces vertically Drive power: Main pump: 1 x 45 kW Pump delivery capacity: 1 x 380 l/min Throughput: up to approx. 280 m3/h under operating conditions Performance at: - 35 kg/m3 bulk weight: approx. 9.5 t/h - 60 kg/m3 bulk weight: approx. 16.5 t/h - 100 kg/m3 bulk weight: approx. 26.0 t/h Hydraulic oil tank volume: 2,100 l Operating voltage: 3 x 400 VAC / 50 Hz / N / PE Other equipment: Operator Panel MP 270 auto ...

used heavy duty paper pulper Manufacturer: PAAL Type: PAL-1800 Year of Make: 2007 Main parts of the machine: 1 drive housing with rotor and externally mounted motor 1 slot 1 Electrical control Weight of the machine approx.: 9,000 kg Capacity up to approx.: 35,000 kg/h Main drive power: 75 kW Total connected load: 82 kW Rated current: 155 A Operating voltage: 400 V, 50 Hz Filling width approx.: 1,800 mm Filling opening approx.: 1,800 x 1,972 mm incl.: 1 set of vibration dampers Functioning: The compact and, above all, large-piece paper types to be shredded must be conveyed into the discharge chute in the correct dosage using a conveyor belt. The rotor tears the material into pressable material and hurls it into the ejection hopper, which is open at the bottom and conveniently located above the conveyor belt leading to the press.  ...

used heavy duty paper pulper Manufacturer: PAAL Type: PAL-1800 Year of Make: 1996 Main parts of the machine: 1 drive housing with rotor and externally mounted motor 1 slot 1 Electrical control Weight of the machine approx.: 9,000 kg Capacity up to approx.: 35,000 kg/h Main drive power: 75 kW Total connected load: 82 kW Rated current: 162 A Operating voltage: 400 V, 50 Hz Filling width approx.: 1,800 mm Filling opening approx.: 1,800 x 1,972 mm incl.: 1 set of vibration dampers Functioning: The compact and, above all, large-piece paper types to be shredded must be conveyed into the discharge chute in the correct dosage using a conveyor belt. The rotor tears the material into pressable material and hurls it into the ejection hopper, which is open at the bottom and conveniently located above the conveyor belt leading to the press. T ...

automatic baler Manufacturer: PAAL Type: KONTI 275 D/k Year of construction 1999 specifications: Pressing force: 75 t Specific pressing force: 9.09 kg/cm² Channel format: 750 x 1,100 mm Bale weight: 500 - 750 kg, depending on material and bale length Filling opening: 1,550 x 1,020 mm Drive power: 75 kW Throughput: 350 m³/h Pressing capacity: - approx. 12.0 t/h at department store (35 kg/m³ bulk density) - approx. 21.0 t/h for mixed paper (60 kg/m³ bulk density) - approx. 33.0 t/h for collected goods (100 kg/m³ bulk density) Binding: 4-fold vertical + 3-fold horizontal Machine weight: approx. 25.0 t

automatic baler Manufacturer: PAAL Type: PACOMAT IS Year of construction: 1988 specifications: Pressing force: 35 t Specific pressing force: 5.51 kg/cm² Channel size: 700 x 700 mm Opening: 800 x 650 mm Drive power: 22 kW Throughput: 100 m³/h with additional manual hopper Wire flow in the pressing direction seen on the left side

automatic baler Manufacturer: PAAL Type PACOMAT II S SO Year of construction: 1994 specifications: Pressing force: 50 t Specific pressing force: 7.14 kg/cm² Filling opening: 1,000 x 650 mm Channel format: 1,000 x 700 mm Drive power: 45 kW Throughput: approx. 170 m³/h automatic 4-fold horizontal binding

An original control cabinet that was dismantled by PAAL Konti 125D, built in 1999. It is based on SIEMENS S5 controller. A complete control cabinet, functional

An original control cabinet that was dismantled by PAAL Konti 275 C, built in 1994. It is based on SIEMENS S5 controller. It is also suitable for other models such as: Konti 200, 275, 325,425, depending on model and drive power. A complete control cabinet, functional We have several channel balers and balers in our warehouse and we cordially invite you to contact us!

An original control cabinet dismantled by PAAL Konti 200B, built in 1987. It is based on analog relays. It is also suitable for the other models such as: Konti 125, 200, 275 , depending on model and drive power. A complete control cabinet, functional

An original control cabinet that was dismantled by PAAL Konti 425 B, built in 1991. It is based on SIEMENS S5 controller. It is also suitable for other models such as: Konti 200, 275, 325, 425, 500, 600, 700, depending on model and drive power. A complete control cabinet, functional We have several channel balers and balers in our warehouse and we cordially invite you to contact us!

An original control cabinet that was dismantled by PAAL Konti 425 B, built in 1991. It is based on SIEMENS S5 controller. It is also suitable for other models such as: Konti 200, 275, 325, 425, 500, 600, 700, depending on model and drive power. A complete control cabinet, functional We have several channel balers and balers in our warehouse and we cordially invite you to contact us!

An original control cabinet that was dismantled by the PAAL Konti 600 E/K, built in 2005. It is based on SIEMENS S7 controller. It is also suitable for other models such as: Konti 700 A complete control cabinet, functional We have several channel balers and balers in our warehouse and we cordially invite you to contact us!

used box press Manufacturer: PAAL Type: HS 34 specifications: Filling box size: 1,000 x 700 x 2,200 mm (W x D x L) Filling opening: - 1st filling: 2,200 x 1,000 mm - 2nd filling: 1,200 x 1,000 mm Press pressure: approx. 18 t Drive power: 4 kW Lifting speed pre-pressing and retraction: 2.5 m/min. Lifting speed repressing: 1.25 m/min. Bale size: approx. 700 x 1,000 x 1,300 mm Bale weight: up to approx. 300 kg Weight of the machine: approx. 2000 kg Machine dimensions: 3,500 x 1950 x 1,450 mm (L x W x H)

automatic baler Manafacture: PAAL Type: PACOMAT IS Year of construction: 1993 specifications: Pressing force: 35 t Specific pressing force: 5.51 kg/cm² Duct format: 700 x 700 mm Filling opening: 800 x 650 mm Drive power: 18.5 kW Throughput: 80 m³/h with additional manual feed hopper Wire passage seen in the direction of pressing on the left side

New hydraulic pump QX61-250/63-100R88 for PAAL channel baler. Can be used in systems with a 75kW motor.