SEEPEX bn used machines

Attachment: eccentric screw pump Manufacturer: Seepex Type: BN 15-6LT Commission no.: 96373 Year of construction: 1997 Flow rate: 14 m ³/h Pressure in the pressure port: 2.00 bar Speed: 344 rpm Motor: kW 2.24 Inlet: DN 80 PN 16 DIN 2533 Pressure connection: DN 65 PN 16 DIN 2533 Material: Main body GG25 Shaft: 1.4021 Stator: NBR Buna Rotor: 1.2436

Attachment: eccentric screw pump Manufacturer: Seepex Type: BN 35-12 Machine number: 176490 Year of construction: 2005 Power: 2-40 m3/h Pressure: 1--8 bar Speed: 1450 RPM. Connection suction side: DN 150 Port side: DN 125 Length: 2400 mm Condition: used, ready

Attachment: eccentric screw pump Manufacturer: Seepex Type: BN 1-12 Machine number: 176411 Year of construction: 2005 Capacity: 150-2200 l / h Pressure: 2 bar Speed: 1400 RPM Inlet connection: DN 50 Port side: DN 50 Length: 1200 mm Condition: used, ready

* General * SKU400X1196 * LocationBarneveld * CEcheck * Pressure * Working pressure24 Bar * Main Features * MaterialStainless steel * Volume130000 Ltr. * Motor1.5 KW * Specified Features - Eccentric Screw Pump * Pumpcheck * Number of pumps:1 * Capacity30-130 m³/h * With motor1,5 kW 400 V 1500 rpm * With frequency invertercheck (as is) * InletDN65 * OutletDN65 * Eccentric Screw Pumps * MaterialStainless steel * Information * MakeSeepex * TypeBCSO * Mach.No.198504 * Floorspace1,35 x 0,20 m * Total height0,25 m * Weight75 kgEccentric Screw PumpsSeepexPumps > Eccentric Screw PumpsBrand > Seepex What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

Cat.-Nr. 12-1090 in a very good condition Capacity: 4000 litres/h Year of Construction: 1981 Masch-Nr. 21628 Original Price: Euro 6000,- Measurements and Weight: LxWxH: 126 x 40 x 109 cm Weight: 115 kg For more Information please contact us under: Phone +49(0)9353-909050 Fax: 09353-9090522, Mobile: 0171-6518248 Subject to prior sale. All prices are valid Ex-Works, excl.VAT. Freight Charges: depending on dimensions and destination.

Used eccentric screw pump SMI - Ruhr pumps Series: SMI Size: 150 Year of construction: 2003 Capacity: 150 m m³/h maximum

For sale is a complete frame sawmill as listed below. (Single sale also possible, please register in advance) An annual cut of up to 60,000 solid cubic metres of round timber is possible with the system. With a log length of 4 metres, the current annual cut is approx. 30,000 solid cubic metres in 1-shift operation. The facility is still in operation and can be visited by appointment. Machine Listing: 01. Log feed 4-strand SPRINGER with separator with roller conveyor with log turner with insert 02. Clamping carriage remotely controlled ESTERER Type: FHZ SV Built in 1990 Track width: 110 cm with auxiliary wagon with cabin 03. Frame saw ESTERER Type: HDS Built in 1973 600 stroke max. passage 71 cm with splitting wedge with drive motor 132 kW with front gear with hydraulic saw clamp with saw blades with hook-up 04. Frame roller conveyor Mayrhofer w ...

Esterer BNK 160/R for prisms and round wood . snow-high 160mm built in 1990 roundwood task, block train, roller aisle with spreissel separator, roller aisle with drop.

Rated power at 50%ED: 80kVA Short-circuit current: 35.9kA Electrode force: 100-600daN/DH Projection: 550mm --- Welding control: Filius classic 128 programs Machine control PLC Siemens S7-1200F --- Incl. additional options: - Double foot switch - Safety valve 2-channel - Pressure-free lowering of the upper fitting - Adjustment device - Forearm support - Flow monitor, electronic - Electrode power switch, electronic - Main switch --- Warranty 6 months --- Training + commissioning on request --- Spot welding electrodes + spare parts available from stock --- Further information on our homepage

BN 102 C Producer Tos Swing 280 mm Distance between centres 630 mm Cross table adjustment 250 mm Longitudinal table adjustment 510 mm Vertical milling head adjustment 290 mm Machine weight 1000 kg

12 stations main turret(6 are driven) - 6 stations sub turret - LNS sprint 552 barfeed new in 2010 - Fanuc 21TB Control.

Resawing saw ESTERER EWD Type: BNK 160 Built in 1986 3-style variable Harmonic machine Cutting height maximum: 165mm Passage width max: 800mm Drive power 2x 75 kW with S-conveyor with Modlwender with chain retraction with centering device at the front with 2-lamella splinter separator with external task (tilt destacking, cross conveyor) good condition - fully functional Can still be viewed during operation. Has been continuously maintained and overhauled. Location: Austria, near Graz

1 CNC lathe (lathe) 2 CNC lathe (lathe) 3 CNC lathe (lathe) 4 CNC milling machine (lathe) 5 2x conventional lathe (lathe) 6 Band saw 7 2x Stand drill All machines work perfectly Pick-up or delivery not until the end of July 2024

- FAGOR 8055 control system - Max. turning Ø: 550 mm - Max turning length: 2000 mm - Tool turret with 8 stations - Travel distance: X= 300, Z= 2150 mm - Quill travel: 150 mm - Dimensions LxWxH: 4200 x 2100 x 2050 mm - Weight: 4,900 kg Accessories: various tools

turning diameter: Ø30/300mm mm turning length: 3055mm +/-0.3mm mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Cycle-controlled lathe Dimensions: 4000 x 2300 x 1800 mm Weight: 4800.00 kg Description: Cycle-controlled lathe with large hollow spindle and high speed, with FAGOR 8055 TC CNC control. Specifications: Turning diameter over bed: 580 mm Turning diameter in the offset: 800 mm Offset length from spindle nose: 280 mm Turning diameter over support 305 mm Center height 290 mm Hollow spindle diameter usable: 80 mm Female thread at spindle end: M85xP1.5 Center width 2200 mm Spindle Spindle speeds: infinitely variable in 2 stages, automatic switching! Level 1: 80 - 750 rpm Level 2: 750 - 2400 rpm Spindle nose: DIN 55026 - A 1/ 8 Recommended chuck size: 250 mm diameter Largest workpiece weight (with steady rest): 2000 kg Feed spindle bearing: 120mm iD/OD Rear spindle bearing: 110mm iD/OD Spindle motor power S1 (100%) / S2 (40%):  ...

Inv. Num. : 8314 Type: 42 BNA DHY Producer: Miyano Created: 2011 Parameters: Max. turning length: 235 mm Max. turning diameter: 80 mm Maximum spindle speed: 6000 1/min Max. rod diameter: 42 mm Weight: 3900 kg Equipment: IEMCA Bar Feeder

12 position upper turret (6 are driven) -10 positionlower turret (5 are driven) - sub spindle - 2 x C axis - equipped with Lns Sprint S2 bar loader with front magazine, fixed and driven tool holders, manuals - Fanuc 18T Control

Mitutoyo 3D CNC Measuring Machine Manufacturer: Mitutoyo Model No.: BN706 Code No. 3700M-312 Type: Coordinate Measuring Machine Granite Measuring Plate Measuring range: X-axis: 700 mm Y-axis: 600 mm Z-axis: 600 mm Table size: 850 x 1200 mm Dimensions: (W x L x H) 1600 x 1800 x 2600 mm Not function-tested More items - new and used - can be found in our shop! International shipping costs on request!

MICROCUT CHALLENGER BNC-2640X, year 2006 -Fagor 8055 -Maximum turning length 1500 -Spindle bore 105 -Turning diameter in the offset 790 -Turning diameter over bed 550 -Turning diameter via face slide 310 -Rod passage 69 mm -X-Path 300, Z-Path 1650 -8 tool positions

A cycle-controlled CNC lathe Microcut of the BNC series is available. Turning length: 2000mm, chuck diameter: 400mm, turning diameter over bed/cross slide: 610mm/330mm, spindle speed: 2500rpm, tool positions: 8. Machine dimensions X/Y/Z: approx. 4000mm/2300mm/1800mm, weight: approx. 4500kg. Documentation available. An on-site inspection is possible.

For sale is a complete, well-maintained used sawmill plant with EWD sawing line, consisting of modern components for log processing, sorting and disposal. The facility has been regularly serviced and is in excellent condition. Part of the line is still in operation and can be visited by appointment. Available from approx. June 2026. System components at a glance: Log yard: Sorting, surveying and debarking plant, SPRINGER, built in 2017 Nicholson debarking machine, built in 1992 Microtec surveying system, built in 2015 30 sorting boxes Cross-cut plant, built in 2017 Sawing line – EWD: Twin-shaft circular saw DWK 700, built in 1999 Profile chipper PF 19-3SP/V, year of manufacture 2003 Resawing circular saw BNK 225/6, built in 2003 Complete mechanization and control Edger EWD Optimes BK-100B Sawn timber sorting and ancillary facilities: 7 sort ...

From a current recycling we offer you a well-maintained CNC lathe MIYANO BNE-65MYY incl. FMB bar feeder SL 80 V. Year of construction:2023 Condition: good Asking price: 180.000,00 VHB Original price: 284.000,00 Location: 78628 Rottweil Equipment / accessories / other information: See appendix Asset Manager: M. Vorkötter Phone: 0202-257273152 Mail: m.vorkoetterakf.de We will be happy to provide you with details upon request. The sale is without warranty Subject to prior sale

Engine Brand: CATERPILLAR, Condition: USED, Engine Cooling Type: Radiator Cooled (std) , Engine Color: Yellow , Flywheel Housing SAE: NO SAE SIZE , Flywheel SAE: Unknown , Engine Condition: Core , Turbo Type: Dry , Exhaust System: Dry , ECU Present?: yes , Starter Voltage: No Starter Present , Injection Type: ECU (Electronic Control Unit) , , https://www.hamofa.com/stock/diesel-engines/caterpillar-3456-bnt-19864 93-used/718, , = More information =, , Type: Engine, Year of construction: 1010, Type number: BNT-1986493; Transport weight [kg]: 1700

turning diameter: 890 mm turning length: 3000 mm turning diameter over slide rest: 550 mm control: Fagor 8055i ATC Revolver: 8 tail stock: MK 6 turning dia. in gap: 1220 mm length of gap: 450 mm spindle passage: 106 mm turning speeds: 15-1480 U/min 3-jaw chuck: 400 mm steady: 300 mm chip conveyor: The tech. Data are manufacturer or operator information and therefore non-binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was creat ...