machines and plants for process engineering used for sale (7,418)

A double column cold mixing system Mixaco is available. Material: steel, usable volume: 800l, motor power: 30kW, mixing vessel: conical, mixing blades: dispersion blades, machine dimensions X/Y/Z: 2900mm/2850mm/3500mm, weight: approx. 4200kg. Documentation available. An on-site inspection is possible.

Goedhart DVS 84637 Internal volume 150 dm3 TS +55/-5 C PS/PT 28/40 bar Fluid R404A

Stock number: PT1572, Material: Stainless acid proof steel AISI 316, In stock: Yes, Amount in stock: 1 pc., Item: Lobe pump, Construction: On a stainless frame, Dimensions: L 1000 x W 400 x H 600 mm, Motor: 1,5 kW - 220/380 Volt - 287 rpm., Theoretical capacity: 3960 l/h, Dimensions inlet: Ø 1½, Dimensions outlet: Ø 1½, Other: Horizontal flow - Flushed sealings

Stock number: PM1576, Material: Stainless acid proof steel AISI 316, In stock: Yes, Amount in stock: 1 pc., Item: Eccentric screw pump, Construction: On a stainless frame, Dimensions: L 1050 x W 250 x H 330 mm, Motor: 2,2 kW - 220/380 Volt - 1400 rpm., Theoretical capacity: 7000 l/h, Working pressure : Max 4,5 bar, Dimensions inlet: Ø 40 mm, Dimensions outlet: Ø 40 mm

This is an opportunity to acquire a complete, ready-to-restart feldspar processing plant and open-pit quarry.The facility has been in operation since 1909 . The operation was closed in early 2023 for strategic and market reasons — not due to any fault in the asset itself. The site includes a fully equipped processing factory, an open-pit quarry with an active environmental and quarrying permit valid until 31 December 2052 all buildings, and approximately 26 hectares of land. The quarry permit is transferable to a new owner. Key Points : - High-value feldspar deposit: Mix of potassium and sodium feldspar (50/50). Low iron content of 0.20% in grinding plant output and 0.14% at the open-pit face. - Strong proven yield: 17,000 tonnes per blast. Approximately 2.6 tonnes of feldspar per cubic metre of solid rock. - Crusher output: 0.4 mm particle size. Capacity of 40 tonnes per hour. - Gri ...

A horizontal single-shaft plowshare batch mixer WAM is available. Nominal volume: 15000l, usable volume: 10500l, mixing ratio: 1:100000, max. residual quantity: 0.1%, discharge angle: 15°, number of shafts: 1, mixing chamber material: carbon steel. Machine dimensions X/Y/Z: approx. 6150mm/2800mm/2550mm, weight: approx. 8000kg. Documentation vorhanden. An on-site inspection is possible.

Used milk centrifuge made by Alfa Laval, type: 3191 with upper and lower fittings. New: 1975

Used milk centrifuge made by Alfa Laval, type: 3191. New: 1973

O.M.S. SALERI, X-188, Item 10, Class 150#, Body CD3MN

Stock number: F1132, Material: Stainless steel AISI 304, In stock: Yes, Amount in stock: 1 pc., Item: Labelling machine, Standing: On legs, Dimensions: L 2050 x W 700 x H 1600 mm, Label size: Max H 120 mm, Label placement: Top, Conveyor: Belt, Conveyor dimensions: L 2000 x W 40 mm, Type: Serie 1000 + M-01, Other: 2 pcs. side belt - Hot print

Stock number: F1127, Material: Stainless steel AISI 304, In stock: Yes, Amount in stock: 1 pc., Item: Unscrambler, Standing: On legs, Construction: Erecting of bottles etc., Dimensions: L 2350 x W 1100 x H 1550 mm, Conveyor: Plastic lamella, Conveyor dimensions: L 1300 x W 82 mm

General SKU221Y083 LocationBarneveld Main Features MaterialStainless steel Volume50 Ltr. Motor0.75 KW Specified Features - Eccentric Screw Pump Pumpcheck Number of pumps:1 Capacity50-80 l/h With motor0,75 kW (400 V 1415 rpm (215 rpm)) InletDN25 OutletDN25 Eccentric Screw Pumps MaterialStainless steel General MakeNetzsch SerialD4095257/6300005469/0100 Year of construction2021StarchOther chemicalRubberPlastic & polymersAgrochemicalsEccentric Screw PumpsFeed additivesDetergent & surf.Food additivesLubricants & oleoOther feedDyes & pigmentsMinerals & inorganicPaints & coatingsNetzschIndustries > Food & Feed > StarchIndustries > Chemical > Other chemicalIndustries > Chemical > RubberIndustries > Chemical > Plastic & polymersIndustries > Chemical > AgrochemicalsPumps > Eccentric Screw PumpsIndustries > Food & Feed > Feed additivesIndustries > Chemical > Detergent & surf.Ind ...

General SKU221Y085 MakeRieger Serial20200536-10 Type3850 l Main Features MaterialStainless steel Volume3850 Ltr. Pressure1 Bar Specified Features - Vertical tank Closed vertical tankcheck Capacity3500 l. (3850 l.) Vessel sizesø 1800 x 2000 mm Conical bottomcheck Manholeø 420 mm Top connectionsDN40 OutletDN50 Max. temperature50 °C MaterialStainless steel 1.4404 (316L) General Year of construction2021 Mounted on legscheck LocationBarneveld Floorspace1,80 x 1,80 m Total height3,00 mGeneric medicinesOintmentsFine chemicalsOther chemicalRubberBiotechnologyPlastic & polymersAgrochemicalsCatalysts & fillersFeed additivesSolventsDetergent & surf.Other pharmaceuticsVertical tanksCosmeticsLubricants & oleoDairyAnimal feedOther feedConfectionerySolid pharmaceuticsBeveragesDyes & pigmentsBiopharmaceuticalAPIMinerals & inorganicPaints & coatingsOils & fatRiegerIndustries > ...

General SKU431X1350 MakeGeppert Band Conveying Systems TypeGES-50-K-W Mach.No.1509113 Year of construction2015 Main Features Motor0.25 KW Length3800 mm Width140 mm Specified Features - Conveyor belt Conveyor beltcheck Elevator beltcheck Belt width140 mm Belt length3800 mm With carrierscheck Carrier height30 mm With motor0,25 kW, 219-241/380-420 volt, (Ex) Belt speed137 rpm Outlet height1300 mm MaterialPlastic, Stainless steel General Mounted on framecheck LocationBarneveld Inclined on framecheck Floorspace3,20 x 0,80 m Total height2,20 m CEcheckStarchRubberAgrochemicalsSpicesConveyor beltsPaper & otherOrganicsE-waste & metalAnimal feedOther feedPlastic & rubberConsumer wasteGeppert-Band GmbHIndustries > Food & Feed > StarchIndustries > Chemical > RubberIndustries > Chemical > AgrochemicalsIndustries > Food & Feed > SpicesConveying systems > Conveyor beltsIndus ...

Various dosing containers, different sizes.

Used disc centrifuge made by Westfalia, type: SA 80. New: 1998. Capacity: 15.000 l/h.

Suction capacity: 6m³, suction pressure: 20 mbar, mix outlet dimensions: 750x800mm. Includes documentation. On-site inspection is available.

Double Z Kneader / Sigma Kneader / Shovel Kneader / Trough Kneader Linden Suitable for highly viscous, tough, plastic or sticky materials such as adhesives, sealants or pastes. Thanks to their two interlocking Z-shaped kneading arms, they can process substances that are hardly homogenizable with normal mixers. - Make HermannLinden, built in 1965 - Machine type K II 60, factory no. 605 - Refurbished in 2025, electrical equipment completely new - Frequency-controlled electric motor 4.0 KW - Frequency converter Optidrive E3 IP66 Outdoor with main switch, potentiometer and reversal of the direction of rotation - Control box with main switch, emergency stop and undervoltage tripping - Speed from approx. 15 to 60 rpm. - Belt drive - 2 Z-waves - All parts in contact with the product in copper and stainless steel - Single-walled copper container approx. 600 x 600 x 450 mm = appr ...

Two Ivat filter towers for dust and smoke with temperature control and nanofilter are available. Air volume flow: 22000-25000m³/h, motor power: 18.5kW, max. separation efficiency: 99.95%, filter area: 120m², filter cartridges: 4, machine dimensions X/Y/Z: approx. 2000mm/1500mm/3000mm, weight: approx. 1200kg. Documentation available. An on-site inspection is possible.

A vertical mixer for powders and granulates Cavicchi is available. Volume: 180l. The machine has an unspecified, presumably electrical defect. Without mixing bowl. An on-site inspection is possible.

Manufacturer: Demag Model: Ergotech 110/470-310 concept Year of Manufacture: 2005 Type of Machine : Injection Molding Machine Find more here - .ucymachines/ Contact us at - sales@ucymachines

Machine Name: Decanter Centrifuge Manufacturer: Alfa Laval NX 4045 Type: 919B-31G Year of Make: 1993 Max. Drum Speed: 3250 1/rpm Material: Stainless Steel Drive motor: 18.5 / 21 kW Inner diameter drum: 353 / 198 Inner drum length: 1200 mm Permissible. Sediment density: 1.2 kg/dm3 Dimensions: Length 3000 x Width 1000 x Height 1150 mm Curb weight: 2500 kg Tech. Documentation: Yes Remark: Eddy current brake Accessories: A control cabinet Condition: Used Price: On request

General SKU322X552 LocationBarneveld MakePfaudler TypeBE 1600 Pressure Working pressure6 Bar Vacuum possiblecheck Working pressure jacket6 Bar Vacuum possible jacketcheck Main Features MaterialGlass Volume1600 Ltr. Motor5.5 KW Specified Features - Glass-lined Reactor Reactorcheck Capacity1600 l. (2309 l.) Vessel sizesø 1500 x 1400 mm Dished bottomcheck Dished top sidecheck Manholeø 500 mm Top connections(2x) ø 100mm, ø 150mm, ø 80mm, ø 50mm, ø 200mm, ø 40mm Outletø 100 mm With jacketvolume 353 l. Max. temperature—10 / 200 °C With propellor stirrercheck Motor5,5 kW, 380—415/660—720 V (Ex) With jacketcheck Glass Reactors MaterialGlass - Enamel (WWG-9115) General No.127912 Year of construction2001 Floorspace1,80x1,80 m Total height4,0 m Weight3000 kgGeneric medicinesOintmentsFine chemicalsOther chemicalBiotechnologyOther pharmaceuticsCosme ...

General SKU297W567 LocationBarneveld MakeDe Dietrich TypeCE 8000 Pressure Working pressure6 Bar Vacuum possiblecheck Working pressure jacket6 Bar Main Features MaterialGlass Volume8000 Ltr. Specified Features - Glass-lined Reactor Reactorcheck Capacity8000 l (9380 l) Vessel sizesDia. 2200x2700 mm Dished bottomcheck ManholeDN600 Top connectionscheck OutletDN150 With jacketcheck With propellor stirrercheck Without motorcheck With jacketcheck Glass Reactors MaterialGlass - Enamel (3009) General No.59877 Year of construction1993 Floorspace2,40 x 2,40 m Total height4,10 m Weight9100 kgGeneric medicinesOintmentsFine chemicalsOther chemicalBiotechnologyOther pharmaceuticsCosmeticsSolid pharmaceuticsBiopharmaceuticalAPIGlass-lined ReactorsDe DietrichIndustries > Pharmaceutical > Generic medicinesIndustries > Pharmaceutical > OintmentsIndustries > Chemical > Fine c ...

General SKU223Y099 MakeAlpine TypeAFG-100 Year of construction1985 Main Features Motor1 KW Inlet diameter35 mm Width100 mm Specified Features - Jet Mill Grindercheck Rotor sizeø 50 mm Grinding room sizeø 100 mm With hoppercheck Inletø 35 mm Motor0,25 kW, (380 V, 2860 rpm (Ex)) With variable speed drivecheck Jet Mills MaterialStainless steel 1.4541 (321) General LocationBarneveld Mounted on wheelscheck With switchgear(as is) Floor space1,70 x 1,10 m Total height2,40 m Extra information Extra SpecificationsWith K-Tron dosing screw, type T20A, 0.25 kW:Becker vacuum pump:Alpine stainless steel filter, type K6R, 2.4 m²:with spare rotors and parts:Tea, herbs & coffeeJet MillsCatalysts & fillersFeed additivesFood additivesSugarAnimal feedDyes & pigmentsMinerals & inorganicAlpineIndustries > Food & Feed > Tea, herbs & coffeeMills > Jet MillsIndustries > Chemical >  ...

General SKU221Y084 LocationBarneveld MakeKelvion Pressure Working pressure10 Bar Vacuum possiblecheck Main Features MaterialStainless steel Size length1350 mm Sizes width323 mm Specified Features - Plate heat exchanger Plate heat exchangerscheck Capacity21,87 l. ConnectionsDN50 Max. temperature100°C Capacity21,87 l. MaterialStainless steel 1.4404 (316L) General Serial112/18916 TypeNT50X CDL.10 Year of construction2021 Floorspace0.932x0,45 m Total height1,40 m Weight270 kgPowdered foodsGeneric medicinesOintmentsTea, herbs & coffeeFine chemicalsStarchOther chemicalRubberBiotechnologyPlastic & polymersAgrochemicalsSpicesCatalysts & fillersFeed additivesPlate heat exchangersSolventsDetergent & surf.Other pharmaceuticsCosmeticsFood additivesSugarLubricants & oleoDairyAnimal feedOther feedConfectionerySolid pharmaceuticsBeveragesDyes & pigmentsBiopharmaceuticalAPIMine ...

Manufacturer: KraussMaffei Model: KM 350-2700 C2 Year of Manufacture: 1998 Type of Machine : Injection Moulding Machine Machine Weight: 16,000 kg CE Certified: Yes Find more here - .ucymachines/ Contact us at - sales@ucymachines

Manufacturer: Engel Model: 330/75 HL Year of Manufacture: 2002 Type of Machine : Injection Moulding Machine Machine Weight: 5,850 kg Find more here - .ucymachines/ Contact us at - sales@ucymachines

Manufacturer: Engel Model: ES 200/90 HL Year of Manufacture: 1999 Type of Machine : Injection Moulding Machine Machine Weight: 5,900 kg Find more here - .ucymachines/ Contact us at - sales@ucymachines

Used colloid mill made by JM Series Colloid Miller. New 2008. 11kW motor.