GEKA hyd used machines

GEKA HYDRACROP 55/S hydraulic ironworker machine was built in 2018 in Spain by MAQUINARIA GEKA S.A. The machine, equipped with 5 work stations, is designed for precision machining of flat bars and angle bars. Each station is controlled by two hydraulic cylinders, which give the possibility to work independently or in parallel on two stations simultaneously. The GEKA HYD 55 S ironworker machine weighs 1390 kg. Technical specifications of the GEKA HYDRACROP 55/S ironworker machine General data - maximum punching force: 55 t - maximum cutting force: 110 t - number of workstations: 5 - number of hydraulic cylinders: 2 - engine power: 5 kW - weight of the GEKA HYDRACROP 55/S machine: 1390 kg Flat bar shearing station - flat bar dimensions: 300 x 15 mm; 200 x 20 mm - blade length: 305 mm - working height: 880 mm Angle bar shearing station - shearing of angle bar at 90°: 12 ...

GEKA HYDRACROP 55/S hydraulic ironworker machine was built in Spain in 2022 by MAQUINARIA GEKA S.L.U. This machine, distinguished by its extensive machining capabilities, is intended for precise hole and corner punching as well as shearing flat bars, angles and solid bars. Each of the 5 work stations is controlled by two hydraulic cylinders, which enable independent or parallel operation at two stations simultaneously. All this makes the offered GEKA HYDRACROP 55 S ironworker machine the perfect choice to significantly increase the productivity of any industrial plant. GEKA HYD 55 S weighs 1200 kg. Technical specifications of the GEKA HYDRACROP 55/S 2-cylinder ironworker machine General data - maximum punching force: 55 t - maximum cutting force: 110 t - number of workstations: 5 - number of hydraulic cylinders: 2 - total power: 5.5 kW - power supply: 400 V; 50 Hz - weight of  ...

GEKA HYDRACROP 110 SD hydraulic ironworker machine was built in 2020 in Spain by MAQUINARIA GEKA S.L.U. The machine is designed for the versatile machining of steel parts, enabling to perform multiple operations on a single machine, which increases production efficiency in industrial plants and locksmith workshops. The GEKA HYDRACROP 110 SD is equipped with 5 individual workstations, designed for punching holes and shearing flat bars, angle bars and steel bars. Each station uses interchangeable tools made of tool steel, which enables adaptation of the machine operation to the current production needs. The stations are controlled by two hydraulic cylinders and separate foot switch controlls, enabling the simultaneous operation of two operators at different stations and increasing production efficiency. All this is complemented by a robust design that maintains high stability during eve ...

GEKA HYDRACROP 110 SD hydraulic ironworker machine was built in 2009 in Spain by MAQUINARIA GEKA S.L.U. It is an extremely powerful and versatile machine designed for complex machining of steel parts, making it ideal for use in both production plants and locksmith workshops. The machine enables multiple machining operations to be performed in one place, such as punching holes and shearing flat bars, angle bars and steel bars. The GEKA HYDRACROP 110 SD is equipped with 5 independent workstations with interchangeable tools made of high-quality tool steel. Each station is hydraulically controlled by two cylinders and separate footswitches. This solution enables the simultaneous operation of two operators at different stations, which results in increased efficiency and production effectiveness. All this is complemented by a robust design, ensuring high stability even under intensive use.  ...

GEKA HYDRACROP 55/S hydraulic ironworker machine built in 2008 in Spain, is a highly versatile and multifunctional machine that allows a wide range of workpiece machining. Its rigid, sturdy structure is equipped with 5 work stations, designed for the precise hole and corner punching, as well as shearing flat bars, angle bars and solid bars. Each work station is controlled by two hydraulic cylinders, which provide the possibility to work independently or in parallel on two stations simultaneously. The GEKA HYD 55/S ironworker machine weighs 1390 kg. Technical data of the GEKA HYDRACROP 55/S 2-cylinder ironworker machine General data - punching force: 55 t - cutting force: 110 t - number of workstations: 5 - number of hydraulic cylinders: 2 - engine power: 5 kW - weight of machine: 1390 kg Flat bar shearing station - flat bar dimensions: 300 x 15 mm; 200 x 20 mm - blade leng ...

Combined profile steel shear and hole punch GEKA type HYD 80 / Hydracrop 80/AMasch. No. 9566 Year of construction approx. 2000Punching force 80 ton. Projection 300 mmPunching up to 40 mm in 14 mm sheet metalFlat material shears 450 x 15 mmAngle steel shears 130 x 130 x 13 mm4 edge shears 45 x 45 mmRound material shears 45 mmRectangular clinker up to 12 mmMotor power 5.5 kWNeching connection 400 volts, 50 Hz stop with el. Stroke release 500 mm - work table with stop at the hole device 550 x 380

55 ton multi station

Met elektrische achteraanslag Ponscapaciteit: 70 ton Dia x plaatdikte: Ø 28 x 20 mm Maximale slag: 80 mm 40 str / min Keeldiepte: 300 mm Werkhoogte: 1065 mm Maximale snijdikte in plaat: 20 mm Bladlengte: 455 mm 90°-snede: 130 x 130 x 13 mm 45°-snede: 90 x 90 x 10 mm Op maat gesneden rond/vierkant: 45 mm Elektromotor (vermogen): 7,5 kW Lengte: 1800 mm Diepte: 1200 mm Hoogte: 2000 mm Gewicht: 1650 kg

Stamping capacity 550 kN and 280 kN Projection 130 mm or 250 mm

: 50 t. weight: 1,8 t hydraulic: ja round bar steel: 40 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

puncher: 100 t round bar steel: 50.0 mm square edge steel: 50 x 50 mm L-beam: 150 x 150 x 13 mm hole punching press: capacity (dia. x thick.): Ø 30.0 x 26 mm shear: flat material: 600 x 15 mm throat: 300 mm work stroke: 80.0 mm work height max.: 1165 / 960 mm total power requirement: 9.0 kW weight: 2250 kg range L-W-H: 2050 x 1200 x 2050 mm ** well-maintained condition (!!) ** current new price approx. 30.000 euros ** special price on request Equipment: - electro-hydraulic profile steel shears with 4x work stations * Flat steel shears * Profile steel shears * Hole punch * notching station - driven by two hydraulic cylinders - Infinitely variable stroke adjustment - Support table at hole punching station - Material scraper - Lateral storage options - 2x freely movable foot switches - Many accessories included in the scope of delivery * swiveling machine lamp * Various punch dies * Spare  ...

round bar steel: 45 mm square edge steel: 45 mm L-beam: 12 mm : 40 flat steel: 450x15 mm L-beam 90°: 152x152x13 mm : 45 mm square edge steel: 45 mm : 12 mm weight of the machine ca.: 2323 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 10 mm Punching force: 55 to : 40x10 mm flat steel: 300x15 oder 200x20 mm L-beam 90°: 120x120x10 mm L-beam 45°: 70x70x7 mm : 40 mm square edge steel: 40 mm : 37 /min. throat: 250 mm weight of the machine ca.: 1.600 kg Basic equipment: - Complete set of blades for flat steel shears - Complete knife set for bar cutter - Complete knife set for angle steel shears - Compl. Standard punching device - Stamp quick release device for punches up to 40 mm diameter - Rectangle notch compl. with hold downs - Complete knife set below for rectangular notching - Upper tool for rectangular notching - Support table for flat material - Punching table with stop - Notch with stop The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 28 min. Punching force: 110 to : 40x20 mm flat steel: 600x15 oder 400x20 mm L-beam 90°: 160x160x16 mm L-beam 45°: 70x70x7 mm : 50 mm square edge steel: 50 mm : 13 mm throat: 300 mm Basic equipment: - Complete set of blades for flat steel shears - Complete knife set for bar cutter - Complete knife set for angle steel shears - Compl. Standard punching device - Stamp quick release device for punches up to 40 mm diameter - Rectangle notch compl. with hold downs - Complete knife set below for rectangular notching - Upper tool for rectangular notching - Support table for flat material - Punching table with stop - Notch with stop The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

puncher: 70.0 t square edge steel: 45.0 x 45.0 mm round bar steel: 45.0 mm L-beam: 150 x 150 x 13 mm hole punching press: capacity (dia. x thick.): Ø 27.0 x 20 mm shear: flat material: 450 x 15 / 300 x 20 mm throat: 300 mm work stroke: 70.0 mm work height max.: 1095 mm total power requirement: 9.0 kW weight: 1925 kg range L-W-H: 1800 x 1200 x 2000 mm ** current new price approx. 25.000 euros ** special price on request Equipment: - electro-hydraulic profile steel shears with 4x work stations * flat steel shears * profile steel shears * hole punch * notching station - driven by two hydraulic cylinders - stepless stroke adjustment - support table at hole punching & notching station - material stripper - side storage options - 2x freely movable foot switches - operating instructions (PDF) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : 2009 : 9725 : prompt, Zwischenverkauf v : Spanien : 14700 € : 1 : 110 to : 300 mm : 5 : 2 : 40x20 (28x28) mm : 80 mm : 17 1/min : 600x15 (400x20) mm : 605 mm : 152x152x13 mm : 50/50 mm : 90x52x13 mm : 5 kW : 2130 mm : 1200 mm : 2200 mm : 2500 kg 2 foot pedals for independent work at 2 stations hydr. drive flat bar shear with hydraulic downholder angle bar shear with minimum deformation by diagonal moving of the blade , with hydraulic downholder round and square bar shear rectangular notching unit punching unit up to diam. 40 mm oilfilling table at the punching station with gauge table at the notching unit with gauge table at the flat bar shear BUYING USED MACHINERY IS A MATTER OF TRUST - OUR TRANSPARENCY PROMISE We offer you maximum security and complete transparency. • HONEST INSIGHTS: Detailed photos and functional videos of the current condition • LIVE ON-SITE CHEC ...

CNC shearing machine manufactured in 2024. This GEKA HYDRACROP 165/300 SD features a punching power of 165 tons and a maximum capacity of Ø 40 x 30 mm or Ø 34 × 34 mm. It includes five workstations for various operations such as punching, shearing, and notching. If you are looking to get high-quality shearing capabilities, consider the GEKA HYDRACROP 165/300 SD machine we have for sale. Contact us for further details.

Large stock of punching material (dies/stamps), spare parts

Hand - Bending bench Manufacturer: GEKA

Key data: 1000 mm, 1 mm

with rebate groove and wire insertion grooves Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out. Sheet width: 1000 mm Sheet thickness: 1.0 mm . Colour: blue Machine weight: 45 kg Space requirement: 1200 x 400 x 1000 mm Shaft diameter: 50 mm

pressure: 55 t punching cross-cut in cmm: mm stroke: 37 Min./20 mm throat: 500 mm stroke: max. 60 mm work height max.: 1060 mm total power requirement: 5 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 2540 mm, 1 mm

Pull-out sheet metal support at the front, sheet metal slide placed at the front under the machine, hand back gauge, automatic hold-down device, dimensional grooves in the table Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out. Sheet width: 2540 mm Sheet thickness steel: 1.0 mm Sheet thickness aluminium: 1.5 mm Colour: blue Machine weight: 500 kg Dimensions: 2800 x 1500 x 1400 mm Cutting gap adjustment fixed Automatic hold-down Fixed cutting angle Back gauge: 650 mm Machine Number: 6.1-5005

GEKA BENDICROP 50 ironworker machine was built in 2018 in Spain by MAQUINARIA GEKA S.L.U. The machine, designed for the comprehensive machining of steel parts, enables a wide range of operations to be performed in one place. This solution significantly improves the production process and reduces the need for additional machines. The GEKA BENDICROP 50 is equipped with 5 work stations for punching holes, bending flat bars, and shearing flat bars, angle bars and steel bars. Each station features high-quality, quick-change tools, which allow the machine to be adapted to current production requirements. The design, based on a rigid, durable frame, ensures high operational stability even during intensive use. As a result, the GEKA BENDICROP ironworker machine is an excellent choice for production plants and locksmith workshops. The total weight of the machine is approximately 1000 kg. Te ...

Key data: 30 mm, 30 mm, 80 mm

Flat steel shears - Flat steel 2° inclination 300 x 10 mm - Flat steel 5° inclination 200 x 13 mm - Knife length 305 mm Profile steel shears - L-profile at 90° 80 x 80 x 8 mm - L-profile at 45° 60 x 60 x 6 mm - Round steelØ 30 mm - Square steel 30 mm 3-point notching station - Flat steel 7mm - Notching depth 50mm - Notching width 40mm Punching station - Punching capacity 450 kN - Material thicknessØ 27 x 13 mm - Projection 175 mm incl. electric stop

: neu : 2026 : 090194 : prompt, Zwischenverkauf v : Spanien : 22400 € : 430.08 € : 1 : 1 : 60 to : 250 mm : 5 : 40 x 11 mm : 32 1/min : 350 x 15 mm : 120 x 10 mm : 45 / 40 mm : 10 mm : max. 150x10 mm : 5.5 kW : 1850 mm : 1300 mm : 2100 mm : 1390 kg with bending station 5 working stations flat steel shear with device to reduce deformation angle iron shear with round- and squarebars opening triangle notcher punching station press brake device for flat steel table at flat steel station table at notching station length stop 1000 mm with contact switch, for angle, flat or bar station hydraulic drive 2 foot release user manual in GERMAN and ENGLISH WE HAVE MORE THAN 700 REFERENCES! The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.