40 REITZ used machine for sale

Agitator 0.37 KW with aluminium propeller 300 mm Electric motor: Electric motor 0.37 KW, 3 x 230/400 volts, n = 1400 rpm, Weight approx. 15 kg. Wave: Precision stainless steel shaft D14, length 500 mm, diameter 14 mm, Material: Stainless steel 1.4301. Stirring organ: Used double-bladed aluminum propeller d = 300 mm.

Pneumatic laboratory heating press REITZ PHP3 – used demonstration machine Pressed press 3 KN (0.3 tons) With heating device up to 250 °C and temperature control - Press force 3 KN (0.3 to) - Pneumatic cylinder make Festo - Pneumatic two-hand control - Press plate guided in 4 guide columns - Working surface between guide columns 200 220 mm - Heating and insulating plate 150 x 250 mm -Temperature - Machine table made of aluminum profiles and PA plate 60060060mm - Total weight approx. 100 kg - Mobile with 4 swivel castors, 2 of which with brakes . Suitable for foil pressing and embossing under heat.

Pneumatic laboratory heating press REITZ PHP3 – used demonstration machine Pressed press 3 KN (0.3 tons) With heating device up to 250 °C and temperature control - Press force 3 KN (0.3 to) - Pneumatic cylinder make Festo - Pneumatic two-hand control - Press plate guided in 4 guide columns - Working surface between guide columns 200 220 mm - Heating and insulating plate 150 x 250 mm -Temperature - Machine table made of aluminum profiles and PA plate 60060060mm - Total weight approx. 100 kg - Mobile with 4 swivel castors, 2 of which with brakes . Suitable for foil pressing and embossing under heat.

Stirring tank REITZ RB300LRW037250 Stainless steel tank 300 liters with agitator 0.37 KW, used gear motor KEB 30 rpm. Stainless steel stirring tank 300 liters with outlet tap 3/4-inch. Diameter 630 mm, container height 990 mm. Tripod height 425 mm. Gear motor: Used gear motor KEB, 3 x 230/400 volts, 0.37 kW, n1 = 1350 rpm, n2 = approx. 30 rpm. With motor protection switch. Shaft: Precision stainless steel shaft D20, length 1000 mm, diameter 20 mm, material stainless steel 1.4301. With rigid coupling 28/20 in stainless steel 1.4571. Stirring organ: Four-bladed inclined blade stirrer, diameter 275 mm, material stainless steel 1.4571. Very slow-running, high-torque agitator.

REITZ RW40300400 agitator for tank containers 4.0 KW / 300 rpm and inclined blade stirrer Worm gear motor IE3: Three-phase motor Moll 3 x 230/400 Volt, 4.0kW, IP55, n1 = 1440 rpm, n2 = 300 rpm, worm gear, i = 1:5, plug-in shaft as output shaft D = 28 mm. 5 m cable and motor protection plug. Shaft: Precision stainless steel shaft D30, length 2000 mm, diameter 30 mm, Material: stainless steel. With 2 x 1000 mm pitch and additional rigid coupling. Coupling: 2 pieces rigid coupling, 1x 28/30, 1x 30/30 mm, material stainless steel Agitator: 2 pieces of double-bladed oblique blade stirrers, diameter 400 mm, material stainless steel 1.4571, welded version. Truss: With 1 piece mounting frame approx. 400 mm x 2600 mm Each longitudinal strut 2600 mm consists of 2 mounting rails 41 x 82 mm profile. With diagonal struts and angles for fixation on tank frames. Frequenc ...

Foldable mechanical heating press with pressing surface approx. 150250mm. Stable press frame made of generously dimensioned aluminium plates and steel joints. Closure of the press plate and heating plate with ratchet. 2 pre-tensioning beams for locking hinges by means of eccentric clamps. With electric aluminum heating plate 400 watts, 1.74 A, heating area approx. 150 250 mm to 250°C, connection 230 V. With sensor and temperature control. Pressure-resistant insulating plate for use in presses. Suitable for pressing, welding transport belts and plastic straps.

Manual Heating Press Reitz MHSP5H - Manual Lifting Screw Press Static Press Force 5 KN (0.5 to) - Portable press frame made of polyamide PA 6G - Manual screw jack with spindle 20 mm, pitch 5 mm - With handwheel diameter 120 mm and handle - Gear reduction ratio 1 : 10, 0.5 mm spindle travel per handwheel revolution, thus only very little hand force required for high pressure. - Table size 100150mm - Clear width 60 mm - Punch size diameter 70 mm with 4 holes 8 mm to attach the Hotplate - Very easy operation due to spindle and worm gear - Total weight approx. 25 kg With 2 electric aluminum heating plates 1200 watts, heating area approx. 150 100 mm to 250°C, connection 230 V. With sensor and temperature control. Pressure-resistant insulating panels at the top and bottom for use in presses. Suitable for pressing, welding and gluing.

Laboratory heating press REITZ EHSP5H – used demonstration machine Heating press with pressing pressure 5 KN (0.5 tons) With heating device up to 200 °C from above and below. - Electric screw press press press force 5 KN (0.5 to) - Screw jack with spindle 20 mm, pitch 5 mm - Gear reduction ratio 1 : 10, 0.5 mm spindle travel per revolution - Clear width approx. 60 mm - Pressing area 100150mm - Heating device with temperature control, 2 heating plates 100 x 150 mm - With TECO electric motor 0.18 KW - With reversing contactor control (up – down buttons) and emergency stop - Motor protection plug against overload, with main switch - Machine table made of aluminum profiles and multiplex plate 700 700 mm - Total weight approx. 100 kg . Suitable for foil bonding and embossing. Due to self-locking of the spindle, long holding time with constant pressure. The scr ...

Used ATEX agitator RW0252800300 – 0.25 KW – 2800 rpm. For smaller containers and drums. ATEX II 2G EEx e II T3 Electric motor: Electric motor VEM motors Thurm GmbH, 0.25 KW, 2-pole, 3 x 230/400 volts, 2800 rpm, IP55. Weight approx. 8 kg. With motor protection plug. Iso F, suitable for frequency converters. Shaft: Precision stainless steel shaft D10, length 500mm, diameter 10mm, Material: Stainless steel 1.4301. With rigid coupling stainless steel 1.4571. Agitator: Double-bladed inclined blade stirrer, diameter 244mm, Material: Stainless steel 1.4571 With PTB-ATEX test certificate.

Laboratory Heating Press EHSP20H – Used Demonstration Machine Table press / electric screw press with pressing pressure 20 KN (2 tons) With heating device up to 200 °C from above and below. Press drive with screw jack gear, reduction ratio 1 : 12, spindle diameter 32 mm, Pitch 6 mm, pressing area approx. 100 150 mm, clear height and stroke approx. 300 mm. Geared motor 0.37 KW, 1,390 rpm, 4-pole, with spur gear i = 1 : 5, Speed 150 mm / min. Max. dynamic load 20 kN. With reversing control, control box and motor protection plug. Sturdy press frame made of steel. Undertable made of high-quality aluminium profiles 4545 mm, table surface 600600 mm, Table top made of multiplex board. Total weight approx. 100 kg. The table press has a pressing pressure of 20 kN (dynamic load). Typical applications are pressing work with exact lining. Suitable for pressing bonding, embo ...

Centrifugal fan REITZ MXE 125-016030-00 Type GR 90° direct drive 45 kW m³/min 160 mm WS 1250 Intake ø 350 mm, outlet ø 275 Workshop tested, very good condition

Semi-automatic drilling device for plastic parts This purely pneumatic drilling device is designed for repeatable drilling of small plastic parts up to approx. 40 x 200 x 40 mm with holes up to 3 mm. Specifications: - Linear axis travel 420 mm - Stroke approx. 30 mm - Height adjustment approx. 100 mm - With 2-hand release - Plexiglass protection on 3 sides - Emergency stop switch - Sturdy, mobile frame made of aluminium profiles - With 4 swivel castors, 2 of them with brakes - Overall dimensions approx. 1000 x 1000 x 1700 mm - Weight approx. 50 kg - With collet for drill bit 1.5 mm Expiration: - Setup: Adjust stop angle to part size - Setup: Alignment of cross table in X and Y - Setup: Set height adjustment to part height - Inserting the part - Triggering via 2-hand button and holding until drilling is completed - Removal of the finished part and placement  ...

Stirring tank 150 liters with agitator 0.6 KW, 900 rpm and inclined blade stirrer 244 mm Container: Single-walled stainless steel tank 150 liters with drain tap. Rollable aluminum frame with aluminum profiles 45 45 mm. 4 swivel castors, 2 of them with brake. Electric motor: Used, powerful electric motor Baumüller, 0.6 kW, 900 rpm, 3 x 230/400 volts. With motor protection plug. Shaft: Precision stainless steel shaft D20, length 700 mm, diameter 20 mm, Material: Stainless steel 1.4301. Coupling: Rigid shaft coupling, material stainless steel 1.4571 Agitator: Double-bladed inclined blade stirrer, diameter 244 mm, material stainless steel 1.4581, blade adjustable in angle.

IBC container agitator 0.75 KW with worm gear motor i = 1 : 10 and inclined blade stirrer 244 mm With truss made of aluminum profiles 45 45 mm. Propulsion: worm gear motor, 3 x 230/400 volts, 2800 rpm, 0.75 kW, IP55, n²=280, Weight approx. 25 kg. Shaft: Precision stainless steel shaft D20, length 1000 mm, diameter 20 mm, material stainless steel 1.4301 Coupling: Rigid coupling made of stainless steel 1.4571 Agitator: Double-bladed inclined blade stirrer, diameter 244mm, material stainless steel 1.4571 Sash adjustable angle

Electric surface press REITZ EHSP522 Pressing surface 200200mm Pressure 5 KN / 0.5 tons Suitable for surface bonding of plastics and composites. On request with: - Heating plate and temperature control - Load cells and gauges for use as test press

Mixing tank 80 liters REITZ MB80 for bulk materials Used open mixing tank approx. 80 liters with geared motor 0.75 KW and inclined blade stirrer 700 mm Application: Mixing of powdered materials. Slow-running, high-torque agitator for powdered mixes. High torque with low energy consumption. Stirred tank: Mobile mixing tank made of stainless steel with bottom slide for draining the mix. All boilers are refurbished and clean. Capacity approx. 80 litres Geared motor: Geared motor Lenze 0.75 KW, 230 / 400 V, 3 phases, 50 Hz, 1410 rpm, IP 55, ratio i = 56, 25 revolutions per minute at shaft output. With motor protection plug to protect the geared motor. Shaft: stainless steel shaft diameter 20 mm, length 500 mm, material 1.4571 Agitator: Double-bladed inclined blade stirrer, diameter 700 mm, material stainless steel 1.4571

Agitator 0.37 KW 910 rpm and 4-leaf folding stirrer 50 / 150 mm for drums With crossbeam made of aluminum profiles 45 45 800 mm. Electric motor, 3 x 230/400 volts, 0.37 kW, IP55, 6 poles 910 rpm, With motor protection plug and shielded supply cable. Placed at an angle on truss. Stainless steel shaft D20, length 800 mm, diameter 20 mm, material 1.4571. With rigid coupling, bare, material stainless steel 1.4571 Impeller: Four-bladed folding stirrer, diameter 150 mm unfolded, 50 mm folded, for drums, material stainless steel 1.4571

Agitator 0.12 KW with gear motor Bauer and 2-wing Inclined blade stirrer 244 mm With traverse made of aluminum profiles 45 45 mm. Gear motor: Bauer worm gear motor, 3 x 230/400 volts, 0.12 kW, n1 = 2700 rpm, n2 = 180 rpm (i= 15), IP 55, weight approx. 8 kg. With motor protection plug. Shaft: precision stainless steel shaft D20, length 1000 mm, diameter 20 mm, Material stainless steel 1.4571. With rigid coupling made of stainless steel 1.4571 Very slow-running, high-torque agitator for use in attachment tanks or cooking kettles.

Agitator 0.12 KW with gear motor SEVA 89 rpm and 2-wing Inclined blade stirrer 244 mm With traverse made of aluminum profiles 45 45 mm. Gear motor: worm gear motor SEVA, 3 x 230/400 Volt, 0.18 kW, n1 = 1340 rpm, n2 = 89 rpm (i = 15), IP 55, weight approx. 8 kg. With motor protection plug. Shaft: precision stainless steel shaft D20, length 1000 mm, diameter 20 mm, Material stainless steel 1.4571. With rigid coupling made of stainless steel 1.4571

Agitator 0.12 KW with used gear motor Bauer 27 rpm and 2-wing Inclined blade stirrer 244 mm With traverse made of aluminum profiles 45 45 mm. Gear motor: Used gear motor Bauer, 3 x 230/400 volts, 0.12 kW, n1 = 1350 rpm, n2 = 27 rpm, M2 = 24.5 Nm, IP 54, weight approx. 8 kg. With motor protection plug. Shaft: precision stainless steel shaft D14, length 500 mm, diameter 14 mm, Material stainless steel 1.4301. With rigid coupling made of stainless steel 1.4571 Very slow-running, high-torque agitator for use in attachment tanks or cooking kettles.

Agitator REITZ RW012X244 Agitator 0.12 KW with gear motor ELVEM and 2-wing Inclined blade stirrer 244 mm With traverse made of aluminum profiles 45 45 mm. Gear motor: worm gear motor ELKEM, 3 x 230/400 volts, 0.12 kW, n1 = 1395 rpm, IP 55, weight approx. 8 kg. With motor protection plug. Available in 3 agitator speeds: n2 = 14 rpm (i = 100), n2 = 23 rpm (i= 60), n2 = 23 rpm (i= 56). Shaft: precision stainless steel shaft D20, length 1000 mm, diameter 20 mm, Material stainless steel 1.4571. With rigid coupling made of stainless steel 1.4571 Very slow-running, high-torque agitator for use in attachment tanks or cooking kettles.

Electric spindle press REITZ EHSP100F as laboratory heating press / demonstration machine Laboratory heating press with pressing pressure 40 KN (4 tons), ratio 1 : 16, spindle diameter 45 mm, pitch 8 mm, spindle stroke 0.5 mm per revolution. Gear motor 0.75 KW, 1,500 rpm, 4-pole, with spur gear i = 1:5, Speed 150 mm / min. Max dynamic load 25 kN. With reversible control, emergency stop and motor protection plug. Total weight approx. 100 kg, table surface 600 600 mm, pressing surface approx. 150 250 mm, clear height approx. 60 mm. Base made of high-quality aluminium profiles 4545 mm, the table top is made of glued plywood top. The laboratory heating press has 40 kN pressing pressure (dynamic load). The spindle is self-locking and thus maintains the pressing force for a longer period of time. For an extra charge with heating plate, insulating plate and temperatur ...

Agitator RW151000300: 1.5 KW – 1000 rpm. Electric motor: Electric motor Siemens or WEG 1.5 KW, 6-pole, 3 x 230/400 Volt, 1000 RPM, IP55. Weight approx. 30 kg. With motor protection plug. Suitable for frequency converters. Shaft: precision stainless steel shaft D30, length 1000 mm, diameter 30 mm, Material stainless steel 1.4571. With rigid coupling stainless steel 1.4301. Agitator: 4-leaf inclined blade stirrer diameter 300 mm. Material 1.4571. Suitable for larger containers of breweries, dairies etc.

For smaller containers instead of tripod agitators: Agitator REITZ RW0251440200 with 0.25 KW / 1440 rpm and inclined blade stirrer With traverse made of aluminium profiles 45 45 mm. Electric motor: 3 x 230/400 volts, 50 Hz, 0.72 A current, 0.25 kW, 1.66 Nm torque, n = 1440 rpm, IP69K, shaft 20 x 40mm, weight approx. 10 kg. Motor protection socket with switch. Shaft: precision stainless steel shaft D20, length 500 mm, diameter 20 mm, Material stainless steel 1.4571 Coupling: Rigid clutch, bare, material stainless steel 1.4571 Stirrer: Two-wing welded inclined blade stirrer, diameter 200mm, material stainless steel 1.4571

Used double-walled agitator 47 litres with agitator 0.12 KW Double-walled stainless steel container, approx. 47 litres container volume, externally heated up to 70°C with temperature control unit / water bath Haake DC 10 and circulation pump. With aluminium traverse made of profiles 45 45 mm and slow running agitator. Agitator with geared motor: Geared motor Georgii Kobold, 230 volts, 0.12 kW, n1 = 2800 rpm, n2 = approx. 20 rpm. Shaft: precision stainless steel shaft D20, length 300 mm, diameter 20 mm, Material stainless steel. Rigid clutch, bare, material stainless steel Stirring organ: Two-winged slanted blade stirrer, diameter 244mm, material stainless steel. Wings adjustable at angle Electric distribution box with 3 sockets 230V, circuit breaker and FI.

Agitator 150 litres with gearbox Rexroth 0.18 KW, i = 25 and propeller stirrer 150 mm Container: Single-walled stainless steel container 150 litres with drain tap. Rollable aluminium frame with aluminium profiles 45 45 mm. 4 steering wheels, 2 of them with brake. Geared motor: Rexroth, 3 x 230/400 volts, 0.18 kW, i = 25, n2=53 rpm. With motor protection plug. Shaft: precision stainless steel shaft D10, length 850 mm, diameter 10 mm, Material stainless steel Coupling: 2 clamping sets 17 to 10 mm, material stainless steel Stirrer: three-winged propeller stirrer, diameter 150 mm, material stainless steel 1.4581

Test press for single-axial pressure tests from 0 to 10 KN (0 to 1,000 KG) Purpose: Test press for single-axial pressure tests from 0 to 10 KN (0 to 1,000 KG / 10 KN maximum load). Without distance measurement. Manual lifting spindle press - Static pressing force 5 KN (0.5 to) - Portable, stable press frame made of polyamide PA 6G - Manual spindle stroke gearbox with spindle 20 mm, incline 5 mm - With handwheel diameter 120 mm and handle - Gearbox reduction 1: 10, per handwheel revolution 0.5 mm spindle path - This requires only very low hand force. - Table size 235 195 mm - Light width 190 mm - Stamp size diameter 70 mm - With 4 holes 8 mm for fixing a larger stamp plate - Very easy to operate by spindle and worm gearbox - Total weight approx. 25 kg Force measuring device: Weighing module with shear rod load cell for nominal load 1,100 kg.  ...

Very fast running agitator 0.25 KW - 3400 rpm. with aluminium propeller 300 mm Electric motor: Used electric motor 0.25 KW, 3 x 230/400 volts, n = 3,400 rpm, Weight approx. 10 kg. With motor protection plug. Wave: Precision stainless steel shaft D14, length 500 mm, diameter 14 mm, Material stainless steel 1.4301. Rigid clutch made of aluminium. Stirring organ: Two-flyer aluminium propeller d = 300 mm.

Agitator 0.25 KW with aluminium propeller 300 mm With traverse made of aluminium profiles 45 45 mm. Used electric motor 0.25 KW, 3 x 230/400 Volt, n = 1375 rpm, Weight approx. 15 kg. With motor protection plug. Shaft: precision stainless steel shaft D14, length 500 mm, diameter 14 mm, Material stainless steel 1.4301. Rigid coupling made of stainless steel 1.4571. Stirring organ: Two-wing aluminum propeller d = 300 mm.

Used beater 0,12 KW with gear motor Bauer 27 rpm and aluminum propeller stirrer 300 mm = 1350 RPM gear motor: Gearmotor Bauer, 3 x 230/400 v 0.12 kW, n1, n2 = 27 U/min., 24.5 NM, IP 54 weight approx. 8 kg = M2. With brake. Shaft: precision stainless steel shaft D14, length 500 mm, diameter 14 mm, material 1.4301 stainless steel. With rigid coupling made of aluminium. Stirrer: Double propeller stirrer, diameter 300 mm, material aluminium very slow running, torque mixer for use in attaching containers or kettles. Also can be used to prevent cavities in powder silos (bridging). With traverse for IBC containers or other containers for extra charge. Caution: Not suitable for aggressive media. 3 pieces in stock.