16 WEINIG moulders used machines

TECHNICAL DATA: Working width mm: 230 Planing height mm: 120 Infeed table length mm: 3500 Number of spindles: 6 Spindle configuration: 1 B: 5,5 KW 2 R: 7,5 KW 3 L: 7,5 KW 4 T: 7,5 KW 5 B: 5,5 KW 6 T: 5,5 KW Spindle diameter mm: 40 Feedrate m/min: 6-36 Rotation speed max rpm: 6.000 Soundproofing cabin: Yes Feeding magazine Weinig - PHV - 2004

WEINIG moulder model UNIMAT 17N with 8 shafts: -useful working measures 170x120mm -gimbal towing and pneumatic pressure -variable feed speed -top feed wheel before the 1st shaft -tandem feed groups in front of the 2nd and 4th shaft -2000mm long entrance plane -with SACOT automatic loader -manual lubrication pump of the table Tree layout: 1-under 2-right 3-left 4-right 5-above 6-under 7-above 8-Universal

WEINIG planer/moulder Unimat 22A with 9 heads Year of construction: 1987 Serial number 222-896. The planer is in good working condition and has been partially overhauled, cleaned and subjected to careful technical controls. • The machine has been thoroughly cleaned and technically checked. • Some wear parts have been replaced. • A test run was carried out to ensure functionality. • The machine is bolted to a wooden structure and is ready for shipment. • The planer and moulder is equipped with all the tools and is sold as such. Further technical data of the machine: Maximum planing width: 220 mm Maximum planing height: 140 mm Diameter of the spindles: 40 mm Spindle speed: 6000 rpm Length of the inlet table: 2 m The machine has a total of 9 spindles with the following configuration: 1. Lower spindle / dressing spindle : 5.5 kW 2. Right spindle /  ...

SPECIFICATIONS: Pre-spindle machine inlet: 2000 mm Working width: 210 mm Working height: max. 120 mm Cardan shaft drive Drive shaft power: 2.2 kW I. Spindle: Bottom (4 kW) II. Spindle: Right (3 kW) III. Spindle: Left (4 kW) IV. Spindle: Right (5.5 kW) V. Spindle: Above (5.5 kW) VI. Spindle: Above (5.5 kW) VII. Spindle: Bottom (4 kW) With tools

SPECIFICATIONS: Planer: 2500 mm Machinable width: max. 210 mm Working height: max. 150 mm Cardan shaft drive Drive shaft power: 5.5 kW Spindle configuration: I. Spindle: Bottom (4 kW) II. Spindle: Right (4 kW) III. Spindle: Left (5.5 kW) IV. Spindle: Right (4 kW) V. Spindle: Top (4 kW) VI. Spindle: Bottom (4 kW) VII. Spindle: Universal spindle (5.5 kW) With tools.

Moulder Weinig PFA 14/7 Specifications: Working width (mm) 140 Waves: 7 1. Shaft: bottom 2nd shaft: right 3rd shaft: left 4th shaft: right 5. Shaft: up 6. Shaft: down 7th Wave: Uni Wave

SPECIFICATIONS: Length of pre-planer machine inlet: 2200 mm Machinable width: 230 mm Machinable height: 120 mm Spindle: Ø 40 mm Number of Spindles: 5 Cardan shaft drive Speed: 8000 rpm Voltage: 380 V Spindle configuration: 1: Bottom (5.5 kW) 2: Right (5.5 kW) equipped with PowerLock HSK 3: Left (5.5 kW) equipped with PowerLock HSK and electronic control 4: Top (5.5 kW) with PowerLock HSK and electronic control 5: Bottom (5.5 kW) equipped with PowerLock HSK EQUIPMENT: Complete with milling

SPECIFICATIONS: Feed length: 1970 mm Working width: 230 mm Working height: 120 mm Spindle: Ø 40 mm Number of Spindles: 5 Direct drive / cardan (0.25 kW x 3 motors) Speed: 6000 rpm Installed power: 22.9 kW Voltage: 380 V Spindle configuration: I Bottom (4 kW) II Right - Left (7.5 kW), Left equipped with electronic control III Top (5.5 kW) equipped with electronic control IV Bottom (4 kW) EQUIPMENT: Complete with tools

SPECIFICATIONS: Feed length: 1970 mm Machinable width: 230 mm Machinable height: 120 mm Spindle: Ø 40 mm Number of Spindles: 6 Shaft drive (4 kW) Speed: 6000 rpm Installed power: 43 kW Equipped with ATS system for automatic adjustment Voltage: 380 V SPINDLE CONFIGURATION: I bottom (5 kW) II right (11 kW) III left (11 kW) III above (11 kW) IV top (5.5 kW) VI bottom (4 kW) EQUIPMENT: Complete with tools Accessories CE

Weinig Quatromat 23 Moulder Specifications: Brand: Weinig Type: Q23P (profileerautomaat) Year of Make: 2003 M-No.: 99567 Feed table: 2000 mm Dressing table adjustment range: 10 mm Joining ruler adjustment range: 10 mm Planing width: 13 - 230 mm Planing thickness: 6 - 120 mm Thickness adjustment: Manuel with Siko counter Width adjustment: Manuel with Siko counter Head dimension: Min. 6*13mm, up to max. 120*230mm Knife shafts: Bottom: ø125 mm Right & Left: ø125-200mm Top: ø125-200 mm Adjustment range dressing shaft: 5 mm Spindle adjustment range axial: 30 mm Min. Product Length: Short Workpiece Length Equipment Central Control: Relay Control Lubrication: Spindle arrangement: Bottom 4.0 KW Right + Left Spindle 5.5 kW Above 4.0 kW Speed: 6,000 rpm Feed: 8 m/min Stepless -1.5 kW Steel and rubber rollers. 1 feed roller electro-pneumatically cycled ...

WEINIG 5-spindle moulder mod. PROFIMAT P23E – CE compliant -Composition: - Oriz. Inf. 5.5Kw -Vert. right/left 7.5Kw - Oriz. sup. 7.5Kw - Oriz. Inf. 4 Kw - Width 230mm - ATS system - Year 1997 (CE)

WEINIG 5+1 spindle moulder mod. PROFIMAT 23 FORTEC - CE compliant - Complete with ATS device - 1st lower horizontal shaft - 2nd vert. Dx - 3rd vert. Sx - 4th upper horizontal - 5° lower horizontal - 6th universal - Width 230 mm. - Cardan drive - Year 2002

SPECIFICATIONS: Machine inlet: 1970 mm Working width: 230 mm Working height: 120 mm Spindles: Ø 40 mm Number of Spindles: 6 Shaft drive Installed power: 38 kW Voltage: 380 V SPINDLE CONFIGURATION: 1: bottom (4 kW) 2-3: right-left (11 kW) 4: top (7.5 kW) 5: bottom (5.5 kW) 6: universal (5.5 kW) EQUIPMENT: Miscellaneous Accessories

SPECIFICATIONS: Feed length: 1980 mm Working width: 220 mm Working height: 120 mm Spindle: Ø 40 mm Number of Spindles: 8 Shaft drive (7.5 kW) Installed power: 64 kW Voltage: 380 V SPINDLE CONFIGURATION: 1: bottom (5.5 kW) 2: right (5.5 kW) 3: left (5.5 kW) 4: right (5.5 kW) 5: top (7.5 kW) 6: bottom (7.5 kW) 7: top (11 kW) 8: bottom (7.5 kW) EQUIPMENT: Complete with accessories

Working width: 220 mm Working height: 120 mm Working height 4-sided: 120 mm Number of Spindles: 10 Spindle arrangement: urlrlououuni Spindle diameter: 50 mm Spindle speed: 6000 rpm Counter bearings: 1-6-7-8-9 Jointer: 1-2-3-4-5-6-7-8-9 Motor powers: 7.5-7.5-11-11-11-15-7.5-11-11- kW Feed speed: 8-80 m/min Feed motor: 18.5 kW Feed: Hydraulic Table lubrication: automatic Weight: 9000 kg Space requirement: 700x160x140 mm Voltage/Frequency: 380V

Code: 0339 Brand: WEINIG Model: PROFIMAT 23/E - CE Standard Automatic 5-spindle moulding machine for the production of frames, furniture parts, windows, doors, moldings, broom handles, wooden toys, and various - CE Standard Features: Heavy-duty base made of solid cast iron Chainless cardan feed: precise, robust, and durable Special feed roller teeth that reduce the depth of entry into the wood Compact feed system Pneumatic pressure on the feed rollers DIGISET WEINIG for left and upper spindles: tool adjustment is performed directly via dual digital displays Technical data: Min/max working width 20/230 mm Max working height mm 120 Feed speed variator 5–24 mt/min Shaft diameter mm 40 Shaft speed rpm 6000 Feed roller diameter 140 mm Pre-planing table length 2000 mm Soundproofing and full protective coating Motorized vertical feed adjustment Side roller pressur ...

WEINIG Hydromat H23 – with 10 spindles, S/N 89321, built in 1999 ** WEINIG Cross Transport HighMech E-1, with 6 flat chains approx. 2000 x 3500 mm ** Hydraulic WEINIG Roller Accelerator Model 814 ** Short infeed table with heavy 4-roller feed Automatic planing machine with reinforced KASCHWIG soundproofing booth 3-sided • Working width max. 230 mm • Working height max. 160 mm • Electronic feed frequency-controlled 8 – 80 m/min. • Feed motor 18.5 KW • 1st spindle bottom 11.0 KW • 2nd spindle right 11.0 KW • 3rd spindle left 11.0 KW • 4th spindle right 11.0 KW • 5th spindle left 11.0 KW • 6th spindle top 15.0 KW • 7th spindle bottom 11.0 KW • 8th spindle top 15.0 KW • 9th spindle bottom 15.0 KW • 10th spindle universal 11.0 KW (4-sided) • Spindle speed 6,000 rpm. • Spindle diameter ø 50 mm • All spindle motors wi ...

TECHNICAL DATA: Width of inlet planer: 1970 mm Working width: 250 mm Working height: 150 mm Spinel: Ø 40 mm Number of Spindles: 5 Cardan shaft drive (2.2 kW) Speed: 6000 rpm Installed power: 22 kW Voltage: 380 V SPINDLE CONFIGURATION: I bottom (4 kW) II-III right-left (5.5 kW) IV above (4 kW) V bottom (4 kW) ACCESSORIES: Complete with tools Miscellaneous Accessories

A Weinig four-sided planer including automation, double cross-cut saw, infeed and extraction system is available. 1) Four-sided planer Weinig Hydromat 22 BL with automatic lubrication, year of manufacture: 1987, working width: 220mm, working height: 140mm, number of heads: 7, head arrangement: bottom/right/left/right/top/bottom/bottom, spindle diameter: 50mm. 2) Kellfass automation unit consisting of double cross-cut saw, length: 5000mm, buffer cross conveyor and pneumatic roller infeed. On-site inspection is possible.

FOUR SIDED PLANER model WEINIG PROFIMAT P 23 E with 5 spindles second hand machine working condition : Excellent CE mark : Yes volt. 380/50 grooved table ( removable ) quick tool locking device with tools : Yes , as in video Composed by 5 spindles , 4 motors : 1° spindle : planer . motor power Hp 5,5 ( Kw 4 ) 2° and 3° spindles : right and left vertical . motor power Hp 7,5 ( Kw 5,5 ) 4° spindle : thickness planer . motor power Hp 10 ( Kw 7,5 ) 5° spindle : planer . motor power Hp 5,5 ( Kw 4 ) grooved table ( removable ) quick tool locking device Technical details : forward motor power Hp 4 ( Kw 3 ) shaft rotation speed rpm 6000 feed speed : from 5 to 24 mt./min. max. useful working width mm. 230 max. useful working height mm. 120 shaft diameter mm.40 inlet length mm. 2000 automatic lubrication system electric height adjustment set of service keys / d ...

FOUR SIDED PLANER model WEINIG PROFIMAT P 23 E with 5 spindles second hand machine working condition : Excellent CE mark : Yes volt. 380/50 grooved table ( removable ) quick tool locking device with tools : Yes , as in video Composed by 5 spindles , 4 motors : 1° spindle : planer . motor power Hp 5,5 ( Kw 4 ) 2° and 3° spindles : right and left vertical . motor power Hp 7,5 ( Kw 5,5 ) 4° spindle : thickness planer . motor power Hp 10 ( Kw 7,5 ) 5° spindle : planer . motor power Hp 5,5 ( Kw 4 ) grooved table ( removable ) quick tool locking device Technical details : forward motor power Hp 4 ( Kw 3 ) shaft rotation speed rpm 6000 feed speed : from 5 to 24 mt./min. max. useful working width mm. 230 max. useful working height mm. 120 shaft diameter mm.40 inlet length mm. 2000 automatic lubrication system electric height adjustment set of service keys / d ...

FOUR SIDED PLANER model WEINIG PROFIMAT P 23 E with 5 spindles second hand machine working condition : Excellent CE mark : Yes volt. 380/50 grooved table ( removable ) quick tool locking device with tools : Yes , as in video Composed by 5 spindles , 4 motors : 1° spindle : planer . motor power Hp 5,5 ( Kw 4 ) 2° and 3° spindles : right and left vertical . motor power Hp 7,5 ( Kw 5,5 ) 4° spindle : thickness planer . motor power Hp 10 ( Kw 7,5 ) 5° spindle : planer . motor power Hp 5,5 ( Kw 4 ) grooved table ( removable ) quick tool locking device Technical details : forward motor power Hp 4 ( Kw 3 ) shaft rotation speed rpm 6000 feed speed : from 5 to 24 mt./min. max. useful working width mm. 230 max. useful working height mm. 120 shaft diameter mm.40 inlet length mm. 2000 automatic lubrication system electric height adjustment set of service keys / d ...

FOUR SIDED PLANER model WEINIG PROFIMAT P 23 E with 5 spindles second hand machine working condition : Excellent CE mark : Yes volt. 380/50 grooved table ( removable ) quick tool locking device with tools : Yes , as in video Composed by 5 spindles , 4 motors : 1° spindle : planer . motor power Hp 5,5 ( Kw 4 ) 2° and 3° spindles : right and left vertical . motor power Hp 7,5 ( Kw 5,5 ) 4° spindle : thickness planer . motor power Hp 10 ( Kw 7,5 ) 5° spindle : planer . motor power Hp 5,5 ( Kw 4 ) grooved table ( removable ) quick tool locking device Technical details : forward motor power Hp 4 ( Kw 3 ) shaft rotation speed rpm 6000 feed speed : from 5 to 24 mt./min. max. useful working width mm. 230 max. useful working height mm. 120 shaft diameter mm.40 inlet length mm. 2000 automatic lubrication system electric height adjustment set of service keys / d ...

FOUR SIDED PLANER model WEINIG PROFIMAT P 23 E with 5 spindles second hand machine working condition : Excellent CE mark : Yes volt. 380/50 grooved table ( removable ) quick tool locking device with tools : Yes , as in video Composed by 5 spindles , 4 motors : 1° spindle : planer . motor power Hp 5,5 ( Kw 4 ) 2° and 3° spindles : right and left vertical . motor power Hp 7,5 ( Kw 5,5 ) 4° spindle : thickness planer . motor power Hp 10 ( Kw 7,5 ) 5° spindle : planer . motor power Hp 5,5 ( Kw 4 ) grooved table ( removable ) quick tool locking device Technical details : forward motor power Hp 4 ( Kw 3 ) shaft rotation speed rpm 6000 feed speed : from 5 to 24 mt./min. max. useful working width mm. 230 max. useful working height mm. 120 shaft diameter mm.40 inlet length mm. 2000 automatic lubrication system electric height adjustment set of service keys / d ...

MULTI MOULDER machine type WEINIG PFA 17N second hand machine 6 spindles with tools - Composition : 1° shaft : surface planer . motor power Hp 5,5 2° shaft : spindle moulder . motor power Hp 4 3° shaft : spindle moulder . motor power Hp 5,5 4° shaft : spindle moulder . motor power Hp 5,5 5° shaft : thickness planer . motor power Hp 5,5 6° shaft : surface planer. motor power Hp 5,5 inlet length mm. 2000 feed speed: from 7,8 to 58,8 mt./min max. useful working width mm. 170 max. useful working height mm. 120 lubrication system weight kgs. 2600 volt. 380/50