Offer 23465 Specifications: - Max. working width 1040 mm - max. material thickness (with a strength of 40 kg) 3.5 mm - Table width 300 mm - Stand projection 100 mm - Working height 880 mm - Front angle stop - 3 additional front support arms - Back gauge adjustable by hand 5 - 550 mm - Drive 400 V / 5.5 kW - E.- Footswitch - Space requirements including back gauge, without front support arms -ca. W 1500 x H 1250 x D 1400 mm - Weight approx. 1400 kg
Engine. Guillotine Shears Impact Shears Tin Shears Scissors Cutting Manufacturer: KRAMER Model TM IIa 3000x4,5 max. cutting length 3050 mm max sheet thickness at ST 40 4.5 mm Distance between uprights 3050 mm Projection 130 mm Table width 360 mm Strokes per min 30 pcs. Hold-down device 16 pieces Manual backgauge travel 5 – 550 mm Engine power 7.5 kw Machine weight 4000 kg Space requirements: W 3480 mm D 3600 mm H 1400 mm Foot switch Back gauge front support arms Angle stop The machine is in good condition and ready for immediate use. Machine runs very quietly. Forklifts available, freely loaded trucks Cheap shipping possible Location of the machine 48324 Sendenhorst for enquiries 0157-35496006 The price is net plus 19% VAT.
Guillotine shears Manufacturer Kramer Type TM II a 4000 Year of construction 1988 2.5 mmm sheet thickness. Machine is in a used very good condition. With invoice and VAT.
Working width: 1040 mm sheet thickness: 12 mm rear gauge: hand up to 500 mm power: 380 V, 11 kW space: 2500 x 2150 x 1900 mm weight: 4100 kg
Working width: 2500 mm sheet thickness: 4 mm throat depth: 70 mm rear gauge: 520 mm power: 380 V, 6.3 kW space: 3200 x 2300 x 1270 mm weight: 4600 kg
Description: maximum capacity 1555 KN serial number 2608 Control: Elgo 85 number of pressure stamps: 21 SICK safety curtain plate width: 4,000 mm, plate thickness: 20 mm, cutting angle adjustment: 3.5 °, rare limit stop: 1,500 mm, column arm: 400 mm, total power requirement: 33 kW, weight approx.: 25,000 kg, Approx. Onsite Dimension. (l x w x h): 4,800 x 2,700 x 2,900 mm
Description: Guillotine shears - manual operation Sheet width 1320 mm Sheet thickness 1.5 mm Distance between columns 1340 mm Back gauge - adjustable 900 mm Connected load manual operation Machine weight approx. 0.25 t Dimensions L x W x H 1.6 x 0.8 x 1.1 mweight approx.: 250 kg, Approx. Onsite Dimension. (l x w x h): 1,600 x 800 x 1,100 mm
METALPRES NHM 3006 hydraulic guillotine shears built in the Czech Republic in 2000, are used for precision cutting of black or acid-resistant steel sheets with a maximum length of 3000 mm. The NHM 3006 T guillotine shears have been regularly serviced and upgraded throughout their lifetime. In 2023, a general overhaul was performed with a net value of approximately PLN 16000, during which seals, clamps, controls, electrical installation with cabinet were replaced and the knives were sharpened. The price of the machine also includes a rack with saw for steel and a rack for sheet metal shown in the photos. The total weight of the METALPRES NHM 3000 3M machine is 2000 kg. Technical specifications of the METALPRES NHM 3006 guillotine shears - maximum cutting length: 3000 mm - maximum workpiece thickness (acid-resistant steel): 5 mm - maximum workpiece thickness (black steel): 6 mm - di ...
sheet width: 3050 mmplate thickness: 6 mmdistance between columns: 3200 mmcutting angle adjustment: 30´- 230´ °strokes: 25-8 p. min.back stop way ca.: 600 mmthroat: - mmtotal power requirement: 5,5 kWweight of the machine ca.: 3,8 tdimensions of the machine ca.: 3,5 x 1,6 x 1,45 mCondition: ready for operation: Video(s) available on our website.: CE signed: Electric 380 Volt: Back gauge electric with counter in front: 2 Geschwindigkeiten Foot switch: Protective railing + photoelectric barrier: Pair of blades for change: Shadow line lighting: cutting angle adjustment: Squaring arm withh mm-scale: 1300 mmSupport arms: 3 x 1300 mmHydraulic plate shears with cutting angle adjustment and back gauge with 2 speeds. Higher quality knives for stainless steel processing.The cutting performance refers to 380 N/mm² strength.The machine was used in a well-kept small business to produce s ...
OSTAS TAFELSCHERE TYPE OGM 1050 x 1.5 - Capaciteit 1050 x 1.5 mm - Achteraanslag - Weight 450 kg DUTCHMACH Metalworking machines ENSCHEDE - NETHERLANDS (3 km from the German border)
OSTAS PLATE SHEAR TYPE RGM 1050 x 6 -Capaciteit 1050 x 6 mm -Achteraanslag electric -Voetbediening -Remmotor -Plaathouders -Noodstop -400V DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)
OSTAS PLATE SHEAR TYPE ORGM 2050 x 3 -Capaciteit 2050 x 3 mm -Achteraanslag electrical -Voetbediening -Fotocelbeveiliging van de achterzijde -Oplegarmen -Verlichting van snijlijn -Remmotor -Noodstop -Documentatie -Weight 2000 kg -400V DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)
OSTAS PLATE SHEAR TYPE ORGM 2050 x 3 -Capaciteit 2050 x 3 mm -Achteraanslag -Voetbediening -Fotocelbeveiliging van de achterzijde -Oplegarmen -Verlichting van snijlijn -Remmotor -Noodstop -Documentatie -Weight 1900 kg -400V DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)
OSTAS PLATE SHEAR TYPE ORGM 3050 x 4 -Capaciteit 3050 x 4 mm -Achteraanslag electrical -Voetbediening -Fotocelbeveiliging van de achterzijde -Oplegarmen -Verlichting van snijlijn -Remmotor -Noodstop -Documentatie -Weight 4100 kg -400V DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)
OSTAS PLATE SHEAR TYPE RGM 1050 x 3 -Capaciteit 1050 x 3 mm -Achteraanslag -Voetbediening -Remmotor -Plaathouders -Noodstop -400V PRICE is plus VAT DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)
Mechanical sheet metal shears of excellent quality, for the burr-free precision cutting of sheet metal up to 1.2 mm sheet thickness steel sheet/ST40 – aluminium 1.5 mm, backdrop-guided knife beam Largest cutting length 4,080 mm, cutting angle 1.5° - up to 25 cutting strokes/min, NC - controlled rear stop with 750 mm travel range, slantable for conical cuttings - automatic removal of the stop rail at sections deeper than 750 mm - with forced-controlled sheet lifting device - automatic tipping device for the sheet metal cuttings into the section collection cart, Scissor table height 800 mm - scissor table width 300 mm - Scissor table extension up to 480 mm support width, dimensions 4.75 m x 1.68 m x H 1.46 m, drive power 2.2 kW, weight approx. 1,500 kg
Mechanical manual sheet metal shears of excellent quality, for the burr-free precision cutting of fine sheets up to 1 mm sheet thickness steel sheet/ST40 – aluminium 1.2 mm, backdrop-guided knife beam, maximum cutting length 3,080 mm, cutting angle 1.5°, manually operated rear stop with 750 mm travel range - +/- 5 mm slantable for conical cutting, optional with sheet metal high-holding device and automatic tipping device for the sheet metal cuttings in the section collection trolley, scissor table height 800 mm - scissor table width 300 mm - scissor table support width up to 480 mm, dimensions 3.55 m x 1.6 m x H 1.3 m, weight approx. 790 kg
Type 52.70 Specifications: Cutting length 1040 mm Sheet thickness in St 2.5 mm Sheet thickness in stainless steel (700 N) 1.5 mm Motorized back gauge up to 500 mm Stroke rate approx. 60 rpm
Sell a table scissors, which was used exclusively for plastic cutting. Manufacturer RAS Type: 50.20 Space requirement 2.5m1.1m1.6m High Cutting length 1020mm Nmyhr Cutting thickness 1.25mm Weight 220kg
sheet width: 2000 mmplate thickness: 2,25 mmdistance between columns: 2040 mmtotal power requirement: 7,5 kWweight of the machine ca.: 1,5 tdimensions of the machine ca.: 2,2x1,7x1,1 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Machine Type: Guillotine Shears Manufacturer: RAS Model: 54.30 Year of construction: 1975 Condition: very good Offer Type: Used Machine Specifications: Capacity: 1040 x 4.0 mm Drive type: el./mech. Propulsion: 7.3 kW Remark: rip fence, Material supports and stop at the front, 2 spare blades Weight: 2000 kg The machine is in a very good condition and ready for immediate use and can be viewed and demonstrated by us. We would be pleased if you are interested in our offer. Errors, modifications and prior sale excepted.
sheet width: 1040 mmplate thickness: 2,50 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: 0,750 tdimensions of the machine ca.: mManual back gauge can be operated from the front up to 500 mmSide stopKnife sharpenedThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Max. cutting length: 1040 mm Max. sheet thickness: 2.5 mm steel Manual backgauge can be operated from the front up to 500 mm Side stop Knife sharpened Weight: 750 kg
Max. cutting length: 2040 mm Max. sheet thickness: 2 mm steel Manual backgauge adjustable from the front up to 550 mm Pneumatic sheet metal holding Knife sharpened Weight: 1100 kg
sheet width: 2540 mmplate thickness: 2 mmstrokes per minute until: 63 throat: 100 mmcutting angle: 1,13 °table height: 750 mmtable width: 320 mmtable height over floor: 750 mmtotal power requirement: 3 kWweight of the machine ca.: 1600 kgdimensions of the machine ca.: 3,1 x 2 x 1,3 mElectric 380 Volt: Rear register front operated: 15 - 550 Foot switch: Squaring arm: Support arms: 3 x Motorized guillotine shears in the swing cutting system with adjustable from the front manual backgauge with analogue display and reading optics. Power transmission via gearbox, eccentric shaft and connecting rod on the cutter bar. Less noise level because the gear is only switched on during the cutting processis. Hold-down beam with continuous pressure element made of elastomersmaterial that ensures secure clamping of the sheet metal.The cutting performance refers to 400 N/mm² strength.Machine dealer w ...
Panel shears Sheet metal scissors used Manufacturer: RAS / REINHARDT Maschinenbau Type: 82.20 Cutting width max. 2040 mm Sheet thickness max. 2 mm 380 V Dimensions approx. 2500 x 1500 x 1100 mm Changes and errors in the technical data, information and prices as well as prior sale reserved.
Guillotine shears Manufacturer: Reinhardt Type: RAS 82.12 Year of manufacture: not specified Cutting length: 1,250 mm Sheet thickness: 2.25 mm Weight: 830 kg
Guillotine shears Manufacturer: Reinhardt Type: RAS 83.20 Year of manufacture: not specified New control system in 2023 Cutting length: 2,040 mm Back gauge: 750 mm Thickness: Sheet steel: 3 mm Stainless steel: 2 mm Aluminum: 4 mm Weight: 2,050 kg Accessories: Incl. spare blade
sheet width: 2300 mmplate thickness: 1,5 mmdistance between columns: 2400 mmimpact length: 1000 mmtotal power requirement: kWweight of the machine ca.: 0,5 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Inv. Num. : 4970 Type: VS 310-6 Producer: Safan Created: 1981 Parameters: Maximum cutting length: 3100 mm Maximum sheet thickness when cutting: 6 mm Maximum cutting angle: 2 h Oil tank capacity: 150 l Total power requirement: 11 kW Back gauge: 1000 mm Machine weight: 6200 kg
SAY-MAK TAFELSCHERE TYPE SRGM 1360 - Capaciteite 1360 x 6 mm - Achteraanslag - Plaathouders voor - Voetbediening - Noodstop - 400V DUTCHMACH Metalworking machines ENSCHEDE - NETHERLANDS (3 km from the German border)
SAY-MAK TAFELSCHERE TYPE SRGM 1360 - Capaciteite 1360 x 6 mm - NC achteraanslag - Small knipped plaat wordt automatically aan de voorzijde van de machine uitgeworpen - Plaathouders voor - Voetbediening - Noodstop - 400V DUTCHMACH Metalworking machines ENSCHEDE - NETHERLANDS (3 km from the German border)
SAY MAK PLATE SHEAR TYPE SRGM H 1400 x 3 -Capaciteit 1400 x 3 mm -CN touchscreen achteraanslag besturing met various functies -Geknipte plaat gets voor-of achter de machine uit (dat kiest u op touchscreen) -Pneumatic plaathouder eighth -Plaathouders voor -Voetbediening -Noodstop -400V DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)
Machine Type: Guillotine Shears Manufacturer: SCHARRINGHAUSEN Model No.: HS-III Year of construction: 1964 Condition: good Offer Type: Used Machine Specifications: Capacity: 2050 x 3.0 mm Drive type: el./mech. Propulsion: 5.5 kW Remark: backgauge, El. foot release, front stop rail, Machine feet Weight: 2700 kg The machine is in good condition and ready for immediate use and can be viewed and demonstrated by us. We would be pleased if you are interested in our offer. Errors, modifications and prior sale excepted.
Working width: 2040 mm Sheet thickness: approx. 1 mm Back gauge: 600 mm Dimensions: 2400 x 1070 x 1100 mm Weight: approx. 900 kg
Working width: 2040 mm Sheet thickness: approx. 1 mm Back gauge: 600 mm Dimensions: 2400 x 1070 x 1100 mm Weight: approx. 900 kg
sheet width: 2500 mmplate thickness: 1,75 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mManual back gauge up to 500 mmSide stop and table extensionKnife sharpenedThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Max. cutting length: 2500 mm Max. sheet thickness: 1.75 mm steel Manual backgauge up to 500 mm Side stop and table extension Knife sharpened
Max. cutting length: 2500 mm Max. sheet thickness: 1.75 mm steel Manual backgauge up to 500 mm Side stop and table extension Knife sharpened
Manual Tin Shears / Guillotine Shears with Table - Heavy-duty design - Adjustable front stop 360 mm - with table and runway Specification - Max. cutting length: 630 mm - Table dimensions WxD: 630 x 540 mm - Front stop: 360 mm - Dimensions WxHxD: approx. 1000 x 1200 x 2000 mm - Weight: approx. 300 kg
Description: serial number: 275  , workpiece thickness: 3 mm workpiece length: 2060 mm plate thickness: 3 mm, weight approx.: 4,500 kg, Approx. Onsite Dimension. (l x w x h): 3,600 x 2,300 x 2,100 mm
Offer 23476 Specifications: - Max. working width 1020 mm - max. material thickness 3.0 mm - Cutting angle 2.7° - electr. Footswitch - Single stroke – continuous stroke can be pre-selected - Manual backgauge up to 500 mm - Front pull-out sheet metal support - Drive 400 V / 2.5 kW - Space requirement approx. W 1450 x H 1200 x D 1400 mm - Weight approx. 900 kg
sheet width: 1530 mmplate thickness: 2,00 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: 0,840 tdimensions of the machine ca.: 1,90 x 1,30 x 1,20 m- manual back gauge 500mm- Hold-down device with hard rubber strip- Sheet metal holding device mechanically controlled to the rear including sheet metal slide- Rear area protection via light barrierThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Schröder MHSU 1500/4,0 - Motorized guillotine shears - Motorized backgauge 750 mm - Hold-down device with hard rubber strip to protect polished sheet metal - Extended extendable support table - All-steel knife 2-flute - Punctures at a distance of 10 mm parallel to the lower knife over the entire course of the table - Selector switch for single and continuous stroke - Rear compartment protection according to CE via 3-beam light barrier and side protective grille -Foot switch - Year of construction 2013 Specification - Effective length: 1530 mm - Capacitance (Rm 400 N/mm²): 4.0 mm - Cutting angle: 2.7° - Stroke rate: 34 rpm - Drive power: 4.0 kW - Nominal power: 5.0 kVA - Power supply: 3x 400 V - Dimensions WxHxD: 2100 x 1410 x 2600 mm - Weight: 1250 kg
Specifications: - Max. working width 3040 mm - max. material thickness 4 mm - Manual cutting angle adjustment - Stroke rate up to 34 1/min - Backgauge with positioning control Pos100 - Table height approx. 850 mm - Front angle stop - 2 front support arms - Rear space protection with light barrier - E-foot switch - Pneumatic connection 6 bar - Drive 400 V - Space requirement without support arms approx. W 4000 x H 1400 x D 2100 mm - Weight approx. 4700 kg
sheet width: 3000 mmplate thickness: 3 mmweight of the machine ca.: t3 support arms1 angle stoppneumatic hold-down deviceBackgauge to be operated by handThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Working length: 1020 mm Sheet power max.: 3.5 mm Dimensions (WxDxH), approx.: 1640 x 1860 x 1390 mm
Inv. Num. : 5431 Type: HNTA 3150/10 Producer: Tomášek Created: 2015 Parameters: Maximum cutting length: 3150 mm Maximum cutting thickness: 10 mm Minimum sheet thickness when cutting: 1 mm Total power requirement: 22 kVA Machine weight: 11.5 t
Panel shears type Н3218Б or H3218B Working width approx. 2000 mm sheet thickness at 400 N/mm² approx. 6.3 mm functioning - Illustrations similar - Plate shear Type Н3218Б or H3218B Working width approx. 2000 mm sheet thickness at 400 N/mm² approx. 6.3 mm Functional - images similar -
Description: working length: 2500 mm max. thickness of cutting material: 10 ,mm S235, S355 manual limiter adjustment machine is mechanical with a flywheel hydraulic sheet metal presses plate thickness: 10 mm, weight approx.: 9,000 kg, Approx. Onsite Dimension. (l x w x h): 3,800 x 2,050 x 2,050 mm