Hydraulic Presses used for sale (135)

Key data: 500 t

Manufacturer: BUCHER-GUYER Model: AEBI 500 Year: 1969 Condition: Used Stock number: 9455 Control system: SIMATIC S 5 (CPUS 115) Compressive force: 500 t Piston diameter: 525 mm Piston rod diameter: 498 mm Stroke length: 412 mm Machine weight: 18000 kg The press underwent a complete overhaul in 1992 (hydraulics and control system). Equipment: Technical documentation Hydraulic power unit Switchgear

PROFI PRESS 15 TON Broaching Press, Workshop Press, Garage Press. Adjustable pressure and speed; Voltage: 380 volts; Capacity: 15 tons; Cylinder stroke: 600 mm; Distance between column 650 mm Auction-ID: A1-48979-17

Hydraulic Press Dunkes HSZ 63 BJ 1999

Equipped with backgauge Lace tools Double guide Foot pedal Auction-ID: A1-49309-176

Hydraulic Press Dunkes HEZ100-400 BJ 1995

Tox Pressotechnik TZ 05.589753 incl. STE 075-904-1/2\" incl. RKZ05.35.100.07H.LF Auction-ID: A7-49330-4

Key data: 300 t

Manufacturer: Hylatechnik Paul Chrubasik GmbH Type: HSSP 300-3-XA4 Machine Type: Hydraulic Press Year of Make: 2000 Condition: used Press force: 3,000 kN Press force: 300 t Stroke: 300 mm Maximum installation height: 800 mm Table surface: 2,000 × 1,550 mm Plunger area: 2,000 × 1,540 mm Passage at the front: 2,000 mm Side passage: 1,050 mm Table height: 800 mm Fast forward: 340 mm/s Working speed 1: 32.5 mm/s Working speed 2: 19.5 mm/s Retraction: 340 mm/s Maximum working pressure: 280 bar Drive power: 75 kW Power supply: 400 V Frequency: 50 Hz Machine weight: approx. 38,500 kg Hydraulic oil tank: approx. 2,000 l Throw pillow: no Equipment: Complete DREHER conveyor system DREHER Belt Unwinder DREHER Belt Feed DREHER belt conveyor system Hydraulic cut impact damping with parallel hold Hydraulic Rolling Blocks Tool change consoles Siemens SIMATIC control ...

HYDRAULIC PUNCHING PRESS Inv. No. 13.085P1 Make SAHINLER Model HKM40 Capacity 40 Ton Punching Ø 20 in 15mm Stroke 50 mm Radius 175 mm Round cutting 30 mm Square cutting 25 mm Angle bar 80 x 80 x 8 mm Flat bar 200 x 13 mm 300 x 6 mm Blade length 356 mm Motor power 3 KW Weight 580 Kg Auction-ID: A1-49027-39

Key data: 250 t

Hydraulic press SCHULER Pressure 250 ton

Used REIS 4-column hydraulic press / try-out press. 380 V, 50 Hz, serial no. 02037 visible on plate. Large working area, hydraulic unit and control panel included. Condition as shown in photos; capacity and full specifications to be confirmed. Auction-ID: A1-49190-1

Key data: 160 t, 1000 mm, 600 mm

STROKE 500 mm TABLE AREA 1000x850 DISTANCE BETWEEN COLUMN 1010mm DAYLIGHT 350 mm Approx speed 400 mm/s Motor: 40 kw

MARTEX Industrie PX 6 hydraulic cardboard press, year 1985, serial no. 218 1185. Professional baler for compacting cardboard and other packaging waste, reducing their volume and facilitating their storage and handling. Robust steel construction machine, equipped with a vertical hydraulic cylinder, a hydraulic power unit with electric motor, a pressure gauge, a control box and a compaction chamber with front door. Auction-ID: A3-46147-37173

Key data: 250 t, 55 mm

Punching Press Minster Clutch Control Diameter 250 ton Stroke 55mm incl. Decoiler Perfecto type 28-12-7

Power 80 ton Auction-ID: A7-49229-29

Key data: 800 t

Manufacturer: Dieffenbacher Model No.: PHP 800 Year: 2008 Condition: Used Stock number: 9354 Compressive force: 800 t Table length: 2000 mm Table width: 1500 mm Stroke: 1250 mm Machine weight: 44000 kg In 2021, a minor modernization was carried out (completely new controls and new safety features).

50 ton gantry press with electronic up and down controls, 230 volt power supply, never used Overall dimensions: 1200 x 500 x 2000 mm Weight: 300 kg Auction-ID: A7-49208-371

Pressure: 16 tons Table dimensions: 800 mm x 410 mm Hammer dimensions: 350 mm Maximum stroke: 90 mm Motor power: 0.9 kW Weight: approx. 500 kg Machine dimensions: 800 mm x 900 mm x 1400 mm Very fast and powerful Two-hand operation for safe use Simple and intuitive operation Machine in perfect working order

2 hydraulic presses and 1 workbench Auction-ID: A7-49229-90

Key data: 315 t, 310 mm, 250 mm

Condition used Press capacity 315 t Stroke 250 mm Daylight 310 mm Table size (left to right) 320 mm Table size (front to back) 385 mm Table height 1250 mm Speed at max. press force 7.5 mm/sec Pressure speed at f max. 0.3 mm/sec Return speed 24 mm/sec Oil quantity 390 l Driving power 380 V/ 50 Hz/ 2.2 kW Dimensions 1950 x 800 x 2000 mm Height of machine above floor 2000 mm Total weight 2.4 t Mode of operation oil hydraulic Calibrating presses Description Contact the seller for more information Interested in this machine?

Auction-ID: A1-49309-8

NC HYDRAULIC SIMPLE PRESS BRAKE NOMINAL FORCE: 3000KN WORKTABLE LENGTH: 5000MM POLES DISTANCE: 3800MM THROAT DEPTH: 400MM STROKE: 300MM MAX OPEN: 600MM POWER: 45KW DIMENSION: 5000MM(L) X 2500MM(W) X 3200MM(L) LOCATION: F39, TGE KINDLY CONTACT: syweetopglove.com.my

Manual gantry press 20 tons Overall dimensions: 1200 x 800 x 500 mm Weight: 100 kg Auction-ID: A7-49514-224

Key data: 300 t, 800 mm, 500 mm

HURSAN 300 tons hydraulic press Year of manufacturing 2021 Table 800x800 mm Stroke 500 mm Possible to inspect under power

Manual gantry press 20 tons Overall dimensions: 1200 x 800 x 500 mm Weight: 100 kg Auction-ID: A7-49514-176

Key data: 300 t, 600 mm, 400 mm

OZKOC 300 tons hydraulic press monoblock frame New in 2025, almost new Table 600x600 mm Stroke 400 mm Possible to inspect under power

50 ton gantry press with electronic up and down controls, 230 volt power supply, never used Overall dimensions: 1200 x 500 x 2000 mm Weight: 300 kg Auction-ID: A7-49514-310

Key data: 400 t, 1000 mm

LAUFFER PRESSES hydraulic press model VA 400 Capacity 400 tons Table 700x1000 mm Possible to inspect under power

Equipped with 3 crimp sets; unused Auction-ID: A1-47359-152

Key data: 600 t, 800 mm, 650 mm

LCM Taiwan, 600 tons hydraulic press New in 12/2014 Table 800x800 mm Stroke 0-650 mm adjustable full specifications attached Possible to inspect under power

Capacity 4 ton, manual, never used Overall dimensions: 500 x 400 x 800 mm Weight: 50 kg Auction-ID: A7-49514-249

Key data: 250 t, 800 mm, 650 mm

LCM Taiwan, 250 tons hydraulic press Possible to inspect under power New in 2014 Table 800x800 mm Stroke 0-650 adjustable

2 stage pump; Max. 100 bar pump 1st stage; 2nd stage does not work then loses pressure. O-ring leak or something like that. Auction-ID: A1-48979-49

Key data: 40 t, 450 mm, 160 mm

Press force 400 kN , table 450x560 , ram 375x300 , distance table joints 340 stroke 160 , puncture hole 100 diameter, silky column passage 220x410

50 ton gantry press with electronic up and down controls, 230 volt power supply, never used Overall dimensions: 1200 x 500 x 2000 mm Weight: 300 kg Auction-ID: A7-49495-371

FRITZ MÜLLER ZE 625-4 hydraulic press was built in Germany by Fritz Müller GmbH & Co. KG. The machine has been continuously maintained and upgraded throughout its service life. The first major overhaul was carried out in 1988 by the manufacturer’s service Machinenfabrik Mueller-Weingarten AG. A second overhaul was carried out in 2020, during which the press was brought up to current safety requirements. As part of this overhaul, a new control system based on a SIEMENS SIMATIC S7 PLC controller and a SIEMENS SIMATIC HMI TOUCH touchscreen operator panel was installed, the entire electrical system was replaced, seals were replaced and light curtains were installed. The FRITZ MULLER ZE 625-4 is an extremely versatile press designed for even the most demanding metal forming operations. It is capable of performing operations such as deep drawing, stamping, forging, straightening large w ...

Rodcraft WP75P; workshop press, bearing press, hydraulic press; Capacity: 75 tons; Air pressure: 7.5 - 8.5 bar; Hydro-pneumatic: yes; Hand-operated: yes; Cylinder stroke: 250 mm; Weight approx: 500 kg; OLD MODEL Auction-ID: A1-48979-11

Key data: 200 t, 80 mm

Inv. Num. : 9036 Type: 200 T Producer: ROSS Created: 2003 Parameters: Control system: DIMECO MCU 24 Compressive force: 200 t Table length: 2100 mm Table width: 1000 mm Stroke: 80 mm Adjusting the ram: 150 mm Machine weight: 36700 kg

According to photos, weight estimated Auction-ID: A1-48554-208

DIEFFENBACHER PO 500A hydraulic press was built in 1978 in Germany by J. Dieffenbacher GmbH & Co. The machine has been regularly maintained and upgraded throughout its service life. In 2017, a major upgrade was carried out, which included replacing the electrical cabinet, installing light curtains and adding a SIEMENS SIMATIC HMI TOUCH touchscreen operator panel. The seals and electrical system were also replaced. The DIEFFENBACHER PO 500A is the perfect choice for even the most demanding metal forming operations. It enables the execution of such operations as die stamping, punching, calibration of forgings and hot and cold bending. All these machining processes are performed with a high press force of up to 500 tonnes, which, combined with a highly dynamic slider, guarantees the best machining results. The machine is also characterised by a rigid body made of thick steel plates and a ...

General Description Heavy-duty industrial hydraulic press with a nominal pressing capacity of 1,200 tonnes. The machine features a massive straight-side / H-frame construction with guided moving slide and is designed for heavy metal forming, pressing, punching and similar industrial fabrication operations. Technical Details Machine type: Heavy-duty hydraulic press Nominal pressing force: 1,200 t Straight-side / H-frame construction Large hydraulic ram / cylinder assembly Guided moving platen / slide Heavy-duty T-slotted working table Substantial die / tooling assembly installed Hydraulic power equipment Push-button operator controls Heavy bolted steel frame construction Condition Used industrial condition. The press appears substantially complete and remains installed with hydraulic equipment, moving slide, working table and tooling present. The main frame and guides show no obvious ca ...

DIEFFENBACHER PO-F 1250 A hydraulic press was built in Germany in 1981 by J. Dieffenbacher GmbH & Co. The machine was regularly maintained and upgraded throughout its service life. In 2016, a major upgrade was carried out, which included replacing the electrical cabinet, installing light curtains and adding a SIEMENS SIMATIC HMI TOUCH touchscreen operator panel. The piston seals were also replaced and measuring scales were added for precise position measurement of the slider, top ejector and lower die cushion. The DIEFFENBACHER PO-F 1250 A is an extremely versatile hydraulic press for demanding metal forming applications. Its main purpose is die stamping of steel components, calibration of forgings, dogging, hot and cold forging, cold forming and other operations that require very high press forces. All these machining processes are performed with a high press force of up to 1250 tonn ...

Manual gantry press 20 tons Overall dimensions: 1200 x 800 x 500 mm Weight: 100 kg Auction-ID: A7-49495-418

Key data: 250 t, 500 mm

(2018) 250t Hidroliksan Hydraulic Press Hydraulic Press with Integrated Die Cushion for Deep Drawing This 2018 hydraulic double-column press is a heavy-duty production unit designed for versatility, featuring a robust 250-ton capacity and high-quality Rexroth and SICK components. With its 100-ton integrated die cushion and generous 500 mm stroke, it is exceptionally well-suited for complex deep drawing and forming operations that require precise pressure control. Technical Details ‍ Machine Type: Hydraulic Double-Column Press Manufacturer: Hidroliksan Model: H-TYPE Nominal Force: 250t Return Force: 50t Stroke Length: 500 mm Speeds: Approach: 160 mm/sec Pressing: 5 – 15 mm/sec Return: 190 mm/sec Working Surfaces: Ram Plate: 1,000 x 800 mm Table Plate: 1,000 x 800 x 100 mm Components: Pump: REXROTH (71cc – 103 L/min) Motor: 22 kW (30 hp), 1,500 rpm ...

Capacity 4 ton, manual, never used Overall dimensions: 500 x 400 x 800 mm Weight: 50 kg Auction-ID: A7-49514-136

Key data: 200 t, 500 mm, 200 mm

(1982) 200t Lauffer Hydraulic Press High-Speed Hydraulic Press with Advanced Shock Absorption This Lauffer hydraulic press is a high-performance machine designed for speed and precision, capable of 2,000 kN of pressing force. Its high-speed designation is backed by a rapid descent speed of 330 mm/sec and a sophisticated 8-fold flat guidance system to maintain ram alignment even under heavy or off-center loads. Technical Details Machine Type: Hydraulic Press Manufacturer: Lauffer Model: RPS 200 Year of Manufacture: 1982 Nominal Force: 200t Max. Return Force: 225 kN Max. Ram Stroke: 200 mm Shut Height: 500 mm Ram Guidance: 8-fold flat guidance Table & Ram Surface Area (W x D): 800 mm x 630 mm Table Hole Diameter: 204 mm Clearance Between Uprights (Front / Side): 840 mm / 320 mm Operating Speeds: Rapid Descent: 0 – 330 mm/sec (steplessly adjustable) Pre ...

Equipped with 10 crimp sets; unused Auction-ID: A1-47359-150

Key data: 200 t

Capacity: 2000kN Year: 2017 Serial: 17X00095 Max Daylight: 1700mm Stroke: 1200mm Max Tooling Base Size: 2500x1500mm Max Advance Speed: 200 mm/s Electrical Supply: 415 Volts Phase: 3 Motor Rating: 50kW Continuous Approx. Net Weight: 25,000kg Max. Top Tool Weight: 10,000kg

Rodcraft WP75P; workshop press, bearing press, hydraulic press; Capacity: 75 tons; Air pressure: 7.5 - 8.5 bar; Hydro-pneumatic: yes; Hand-operated: yes; Cylinder stroke: 250 mm; Weight approx: 500 kg; OLD MODEL Auction-ID: A1-48979-10

Hydraulic Press DEGUMA P12-12 II

TOX Pressotechnik Hydropneumatic Clinching Pliers TZ 05.573508 Auction-ID: A7-49330-11