used Bending Presses for sale

Working width 2000 mm, depth stop approx. 500 mm, YOC 84 Control

Description: The Adira PA16030 is an unused press brake with a 1600 kN capacity and 3000 mm working length. Control Control System: CYB Touch 8 Numerical Control: Cybelec VisiPAC Working Parameters Condition: New/Unused Capacity: 1600 kN Working Length: 3000 mm Distance Between Housings: 2550 mm Max Stroke: 260 mm Max Open Height Without Tools: 500 mm Throat Depth: 400 mm Motor and Power Motor Power: 15 kW Speed Approach Speed: 150 mm/s Working Speed: 10 mm/s Returns Speed: 150 mm/s Speed X: 800 mm/s Speed R: 200 mm/s Speed Z-Z1/Z2: 1200 mm/s Speed X1: 100 mm/s Axis Travel Stroke X: 625 mm Stroke R: 200 mm Stroke Z-Z1/Z2: 90 to 2150 mm Stroke X1: +/- 100 mm Dimensions Length: 3760 mm Width: 1840 mm Height: 2910 mm Transportation Height: 2710 mm Weight Weight: 7900 kg Extra Equipment Table: 13 mm for Wila type Dies 'Table Kit III' Back Gauge: Z1/Z2 Front Support Arms: 2 arm ...

Offer 23339 Specifications: -.max. Working length 2550 mm - Column passage 2050 mm -.max. Press force 63 t - Table width 125 mm - Projection 450 mm - Max. stroke 100 mm -.max. Installation height 310 mm - Table height 900 mm - Drive power approx. 5.5 kW - Space requirement approx. W 3300 x H 2100 x D 1400 mm - Weight approx. 4.9 t - with: - man. Back gauge - Separate control panel with foot switch - split sharpening tool + universal die

Defects: - Monitor defective

Control Amada Pressing force ... 100t Bending length... 3000mm controlled axes ... 7 Drive... Hydraulic The machine is in good condition, possible to test under power.

sheet width: 3050 mmplate thickness: 12 mm: 1000 mm0: 16 St.machine weight ab.: 7.260 kgdimensions: 3560 x 1820 x 1960 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Description: Nominal force: 1 700 kN Beam width: 4 230mm Table width: 180mm Work surface height: 960mm Inlet: 450mm Actuator travel: 180mm Goose neck: 410mm Distance between end plates: 3760mm Max. pressure: 308 Bar Oil content: 150L Number of cycles: 4 Motor power hating: 11KW Pump activity: 20,7 n3/rev. Approachspeed: 100mm Working speed: 1>, 8 Retract >,80throat: 410 mm, bending length: 4,230 mm, stroke: 180 mm, stroke speed -forwards: 100 mm/min, table surface area l x w : 4320x180 mm, total power requirement: 11 kW, weight approx.: 12,500 kg, Approx. Onsite Dimension. (l x w x h): 5,500 x 2,400 x 2,920 mm

Description: 100 ton power Total bending length 3,100 mm Distance between uprights 2,705 mm Gooseneck depth 420 mm Motor power 11 kW Apron travel 200 mm 7 axes Y1 Y2 X1 X2 R Z1 Z2. CNC OP 2000. Sick' gateweight approx.: 6,500 kg, Approx. Onsite Dimension. (l x w x h): 3,800 x 2,090 x 2,635 mm

Offer 24160 Specifications: - Max. working length 3110 mm - Column passage 2700 mm -Max. Press force 100 t - Projection 415 mm - max. stroke 200 mm - Max. installation height 470 mm - Table height approx. 960 mm - Table width 60 mm - Feed speed / rapid traverse 1 - 100 mm/s - Pressing speed 1 - 10 mm/s - Retraction speed 1 - 100 mm/s - Drive power 7.5 kW - Space requirement approx. W 4300 x H 2950 x D 2300 mm - Weight approx. 7.5 t - With: - CNC control AMADA - for Y1+2 , X, Z - AMADA DIGIPRO measuring system -Light barrier - E.- Footswitch - Miscellaneous tools

Description: Maximum tonnage: 1000kN CN AMNC 4 AXES Equipped with high speeds bending length 3110mm Clearance between uprights 2705mm Gooseneck depth 420mm Motor power 17kW Maximum stroke: 200mmthroat: 420 mm, Max. pressing force: 10 to, bending length: 3,110 mm, number of controlled axes: 4, total power requirement: 17 kW, weight approx.: 15,000 kg, Approx. Onsite Dimension. (l x w x h): 4,500 x 2,000 x 2,700 mm

Inv. Num. : 7140 Type: HG 1703 Producer: Amada Created: 2022 Parameters: Control system: AMADA AMNC 3i Duty cycle: 6664 h Hours: 5511 h Number of strokes: 450794 Compressive force: 170 t Maximum bending length: 3110 mm Maximum ram stroke: 250 mm Maximum lifting speed: 220 mm/s Maximum bending speed: 20 mm/s Maximum retraction speed: 250 mm/s Total power requirement: 30 kW Machine weight: 15000 kg Equipment: 5-axis backgauge Footswitch with panic stop function Angle Measuring System Digipro Safety device AKAS III Wila tenses Handwheel

offer 22499 Specifications: -.max. Working length 3100 mm - Stand passage 2600 mm -.max. Pressing force 100 t - Projection 400 mm - stroke 100 mm -.max. Installation height 370 mm - Table height approx. 960 mm - Delivery speed / rapid traverse 85 mm/s - Press speed 10 mm/s - Retraction speed 80 mm/s - Drive power 11 kW - Space requirement approx. W 3500 x H 2300 x D 1950 mm - Weight approx. 8.0 t - with: - 3 axis CNC control CYBELEC - - CNC – Backgauge 0 - 600 mm - split sharpening tool - split V matrices - Support arms

Description: 125 tonne power Total bending length 3100 mm Distance between uprights 2705 mm Gooseneck depth 420 mm Motor power 11 kW Apron travel mm 200 OPERATOR digital control. 3 axes Y X1 X2. New tooling lineweight approx.: 6,600 kg, Approx. Onsite Dimension. (l x w x h): 3,800 x 2,090 x 2,635 mm

Compressive force: 135 t Working width: 4100 mm Clear stand width: 3150 mm Stand projection: 250 mm max. installation height: 310 mm Working speed: 7 mm/sec Return stroke speed: 50 mm/sec electr. Connection: 400 V, 11 kW Bcyhrjh9qri Weight: 10.8 t Space requirements: 4250 x 1800 x 2400 mm

pressure: 200 tchamfer lenght: 3660 mmdistance between columns: mmControl: total power requirement: kWweight of the machine ca.: 13,50 tdimensions of the machine ca.: m• 2 stop fingers, can be moved laterally• Block die with: V75, V50, V40, V25, V20, V10(V50 and V25 defective at approx. 10cm in the middle)• Straight punch, height 200mm, length 3000mm, segmented• ATL 500 control for immersion depth (Y) and back gauge (X)• Centrally adjustable crowning• 2 support arms• Operation manualThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Offer 24027 Specifications: - Printing capacity 135 t - Working width 3100 mm - Passage between uprights 2600 mm - Table width 180 mm - Projection 250 mm - Installation height 325 mm - Feed speed 70 mm/sec. - Working speed 7 mm/sec. - Retraction speed 60 mm/sec. - Plunger stroke 120 mm - Fixed stop adjustment range 120 mm - Drive 400 V / 7.5 kW - Oil filling approx. 300 l - Space requirement approx. W 3300 x H 2300 x D 1600 mm - Weight approx. 7500 kg - With: - Swivel arm control panel with LC actual value display - for adjusting the pressing depth + pressing pressure + back gauge - Motorized backgauge - 4-fold universal die + sharpening tool + deer foot tool - Two-hand control panel with foot switch - Support arms

pressure: 180 tchamfer lenght: 4100 mmdistance between columns: 3150 mmstroke - stepless adjustable: 200 mmcolumn arm: 300 mmtable height: 1090 mmdayligth: 450 mmworking feed: 9,0 mm/secreturn speed: 80,0 mm/secControl: NC ATL 550 hydraulic: 235 barvoltage: 380 Vtotal power requirement: 15,0 kWweight: 14200 kgrange L-W-H: 4400 x 1900 x 3000 mmFurnishing:- NC controlled hydraulic press brake with torsion shaft- ATLANTIC NC control ATL 550 Positioning of backgauge ( X ) Depth setting positioning ( Y1+Y2 ) Possibility of programming different programs Storage capacity max. 200 programs - max. 400 sentences Pivoting control panel, front left- electric back gauge with 2 stop fingers, manually adjustable on ball screws- manual table crowning, with analogue display- divided deer foot upper tool 85°- divided MultiV - universal matrix block- rear protection- free-moving 2-hand / double-foot oper ...

pressure: 200 tchamfer lenght: 4100 mmdistance between columns: 3150 mmstroke - stepless adjustable: 200 mmcolumn arm: 300 mmtable height: 1090 mmdayligth: 450 mmworking feed: 9,0 mm/secreturn speed: 80,0 mm/secControl: NC ATL 550 hydraulic: 265 barvoltage: 380 Vtotal power requirement: 18,7 kWweight: 15000 kgrange L-W-H: 4400 x 1900 x 3000 mmFurnishing:- NC controlled hydraulic press brake, with torsion shaft- with ATLANTIC NC control ATL 550 Positioning of backgauge ( X ) Depth setting positioning ( Y1+Y2 ) Possibility of programming different programs Storage capacity max. 200 programs - max. 400 sentences Pivoting control panel, front left- electric backgauge, on ball screws with 2 stop fingers, manually adjustable- manual table crowning, with analogue display Adjustment at the front left, with a hand crank- divided deer foot upper tool 85°- reversible MultiV - universal die block-  ...

AYEL-TECH PRESS BRAKE/WORKSHOP PRESS KBWP type 1050 x 100 ton -Capaciteit 1050 x 100 ton -Max Queen 1050 mm -Geeredschap -Pressure gauge -Noodstop -400V PRICE is plus VAT DUTCHMACH Metal working machinery ENSCHEDE - NETHERLANDS (3 km from the German border)

pressure: 160 tchamfer lenght: 3100 mmdistance between columns: 2550 mmtotal power requirement: 11 kWweight of the machine ca.: 8,5 tdimensions of the machine ca.: mmotorized arrestertoolsTechnische Daten / technical details:Druck / pressure 160 toAbkantlänge / bending lenght 3100 mmDurchgang zwischen den Ständern / distance between columns 2550 mmAusladung / overhang 310 mmAntriebsleistung / drive capacity 11 kWGewicht / weight 8500 kgTechnische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich -Technical data, accessories and description of the machine are not binding.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 180 tchamfer lenght: 3700 mmdistance between columns: 3250 mmthroat: 270 mmstroke: 220 mmajustment speed: 80,0 mm/secworking feed: 10,0 mm/secreturn speed: 58,0 mm/secdayligth: 395 mmtable width: 200 mmwork height max.: 870 mmoil volume: 210 ltr.total power requirement: 15,0 kWweight of the machine ca.: 12100 kg.range L-W-H: 4200 x 1470 x 2550 mm from a maintenance workshop ()Furnishing:- conventional electro-hydraulic press brake with torsion shaft for parallelism of the upper beam- electric back gauge, with ball screws (X axis) with 2x manually adjustable stop fingers Fine adjustment via handwheel at the front, with analogue position display- electro-motor adjustment of the immersion depth (Y1+Y2 axis) with digital position display- swiveling operation, mounting side on the left- 1x set of upper tools / additional divided tools- 1x rotating Multi V universal matrix block- 2x  ...

pressure: 40,0 tchamfer lenght: 1600 mmdistance between columns: 1200 mmcolumn arm: 200 mmram stroke speed: 60,0 mm/secreturn speed: 8,0 mm/secwork speed: 60,0 mm/secwork stroke: 100 mmtable height: 760 mmtable width: 150 mmoil volume: 130 ltr.voltage: 400 VoltControl: NC total power requirement: 4,0 kWweight: 3030 kgrange L-W-H: 2050 x 1800 x 2030 mm Exhibition machine - like NEW ()Furnishing:- compact hydraulic press brake- BERNARDO NC control model E21- swiveling control panel- electrical adjustment of the backgauge- Back stop on recirculating ball spindles- electrical adjustment of the immersion depth- Laser protection device in front- Upper deer foot tool - divided- Tool holder with quick change system- Universal die block- side + rear protective device- 2x front support arms- movable double foot switch (operation)The data for this ad was created with ModulMWS - the software solutio ...

Description: - Operating voltage: 3 X 380 V - Frequency: 50 HZ - Rated current: 21 A - Sheet passage: approx. 2000 m - with electrically adjustable stop - Pressing force: Presumably 100 tonnes - Attention: The press brake tools on the machine are not included in the scope of delivery. However, the accessories on the pallet are included in the scope of sale.serial number: 591 06 3165, bending length: 3,100 mm, control: Swissax Euro III, weight approx.: 7,000 kg, Approx. Onsite Dimension. (l x w x h): 4,000 x 1,400 x 2,500 mm

pressure: 060 tchamfer lenght: 2050 mmdistance between columns: mmnumber of strokes - stepless: compressed air: 8 barclosing speed: 200 mm/sectotal power requirement: kWweight of the machine ca.: 6,00 tdimensions of the machine ca.: 3,00 x 2,10 x 2,35 m• Controlled axes: Y1, Y2, X, R, Z1, Z2• Hydraulic tool clamping above + below• CNC controlled crowning• 2 support arms• 1 set of upper tools, length approx. 2200mm, R1, segmented• 1 die set V12/88°, length approx. 2000mm, segmentedThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 75,0 tchamfer lenght: 2620 mmdistance between columns: 2055 mmcolumn arm: 400 mmajustment speed: 100 mm/secworking feed: 10,0 mm/secreturn speed: 90,0 mm/secstroke: ~ 140 mmdayligth: ~ 360 mmtable height: 930 mmtable width: 85,0 mmControl: ELGO P8822 oil volume: 150 ltr.engine output: 7,5 kWweight of the machine ca.: ~ 6.500 kg.range L-W-H: 3700 x 1800 x 2700 mmFurnishing:- electro-hydraulic conventional NC press brake- Swivel control front right, with ELGO P8822 control unit digital position indicator Entry of target/actual values possible- Electro-motor backgauge - X axis Travel = 700mm- electrical adjustment of the immersion depth - Y axes- with 2x manually adjustable stop fingers (R+Z axis)- Upper tool holder with upper wedge crowning - AMADA system- Lower tool holder - System AMADA- very many diverse / divided upper tools- rear guard (door)- lateral protective device (door ...

pressure: 160 tchamfer lenght: 3100 mm: 600 mm: 150 mmStroke: 200 mmdistance between columns: 2550 mmtable height: 925 mmoil volume: 260 lweight: 9800 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Description: Pressing force: 3,200 KN Mains voltage 400 V max. closing speed: 200 mm/s max. air pressure: 8 bar Optionally, the machine can be disconnected and loaded for €2,000.00. In this case, a BF3 transport permit is required.serial number: 04/460/002, Max. pressing force: 326 to, control: ModEva 12, stroke: 565 mm, total power requirement: 22 kW, weight approx.: 28,800 kg, Approx. Onsite Dimension. (l x w x h): 5,200 x 3,200 x 3,800 mm

pressure: 050 tchamfer lenght: 1600 mmdistance between columns: mmstroke: 150 mmthroat: 390 mmtotal power requirement: 5,50 kWweight of the machine ca.: 4,80 tdimensions of the machine ca.: 2,55 x 1,70 x 2,45 m• Controlled axes: X, R, Y1, Y2• FIESSLER safety light barrier• Amada tool holder• Control: CYBELEC 2D graphics type DNC 880S• Die V12/30°, L = 16100mm• Die V8/30°, L = 1,420 mm• Offset punch R0.8/88°, H 130mm, L = 1600mm• Straight punch R0.8, H 90 mm, L = 1455 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 320 tchamfer lenght: 4100 mm: 600 : 250 : 2900 mmStroke: 265 mmthroat: 400 mmdistance between columns: 3750 mmdayligth: 550 mmtable width: 60 mmoil volume: 600 lweight: 29.000 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Description: 170 ton power Bending length 3050 mm Distance between uprights 2500 mm Gooseneck 250 mm Stroke 250 mm Rebuilt and brought up to standard in 2003 Cybelec DNC 60 numerical control. New tooling lineweight approx.: 12,000 kg, Approx. Onsite Dimension. (l x w x h): 3,500 x 1,700 x 3,100 mm

Description: Rated capacity 4050 x 200 T Stroke 250 mm Weight 19 T Rebuilt and brought into compliance by Descombes Précimeca in 09/2016weight approx.: 19,000 kg, Approx. Onsite Dimension. (l x w x h): 4,200 x 1,600 x 3,000 mm

pressure: 140 tchamfer lenght: 3000 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mStocknumber 2010012Type of machine PressbrakeMake COLLYType 3000/140Build in nbChamfer lenght 3000 mmPressure 140 tonStroke 250 mmThroat 310 mmDaylight 520 mm Additional informationincl. 1 set of toolingThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Description: 135 ton power Total bending length 3100 mm Distance between uprights 2600 mm Gooseneck depth 450 mm Motor power Kw 11 Apron travel 450 mm Equipment : 9 axes Y1 Y2 X1 X2 R1 R2 Z1 Z2 NC Cybelec Modevaweight approx.: 12,000 kg, Approx. Onsite Dimension. (l x w x h): 3,800 x 1,865 x 3,010 mm

Description: 63 tonnes of power Total bending length 3100 mm Distance between uprights 2550 mm Gooseneck depth 250 mm Motor power 5.5 kW Deck travel 150 mm 4 axes Y1Y2 X R pneumatic. New Cybtuch 8.' digital control.weight approx.: 7,000 kg, Approx. Onsite Dimension. (l x w x h): 3,500 x 1,700 x 2,280 mm

Darley EHP 200 Press Brake Manufacturer: Darley Type: EHP 200 31/25 Year of manufacture: 1990 Control System: Delem Technical Specifications Effective length: 3100 mm Capacity: 200 t Distance between columns: 2550 mm Main motor power: 15 kW Dimensions: approx. L 3.3 x W 1.7 x H 2.5 m Weight: approx. 9 t Accessories Documentation for the machine A set of tools

pressure: 320 tchamfer lenght: 3200 mmdistance between columns: 2740 mmstroke: 400 mmCenter of spindle to wall or column: 420 mmdayligth: 650 mmengine output: 32,5 kWoil volume: 350 lControl: total power requirement: kWweight of the machine ca.: 20 tdimensions of the machine ca.: 4,75 x 2,80 x 3,60 mOnly 5406.9 operating hours read• Delem DA-65W control• LazerSafe light barrier• Controlled axes: Y1, Y2, X, X1 (oblique), Z1, Z2• 2 x support arms with parking position on the side• CNC controlled crowning• Hydraulic tool clamping at top + bottom• Extensive tool set, with very large dies for machines / steel constructionThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 220 tchamfer lenght: 4050 mmdistance between columns: 3550 mmthroat: 450 mmstroke: 350 mmdayligth: 600 mmajustment speed: 140 mm/secbending speed: 10 mm/secreturn speed: 130 mm/sectotal power requirement: 22 kWweight of the machine ca.: 12 t- upper tool, divided 4050 mm (new)- block tool 4050 mm: V16, V50, V20, V35 (new)- Pneumatic tool clamping above- CNC controlled crowning- controlled axes: Y1, Y2, X, X1, R, Z1, Z2- Support arms movable on linear guide and height adjustable- Fiessler photocell- Stmer ESA S560 TouchThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 6443 Type: TECHNICA PLUS Producer: DERATECH Created: 2009 Parameters: Control system: Cybelec DNC 880 S Operating hours: 3040 h Compressive force: 250 t Maximum bending length: 4100 mm Total power requirement: 18.5 kW Machine weight: 18000 kg Equipment: Tools 2-axis backgauge

Hydraulic, up to 12mm, cutting length: 3050, weight: 15to, L-350, W-220, H-240cm

Hydraulic press brake Manufacturer: Durma Country of manufacture: Türkiye Year of manufacture: 2014 Control: CNC 4-axis Cybelec type Force: 600t Bending Length: 6050 mm Distance Between Columns: 5100 mm Stroke: 365 mm Daylight: 700 mm Throat Depth: 510 mm Table Height: 990 mm Table Width: 154 mm Working Speed Y Rapid Speed: 80 mm/sec Y Working Speed: 7 mm/sec Y Return Speed: 80 mm/sec Motor Power 45 kW Length: 760 mm Width: 2650 mm Height: 3850 mm If you are interested, don't hesitate to contact me. I will send the price, photos and additional information.

pressure: 160 tchamfer lenght: 3550 mmstroke: 200 mmquantity of oil: 150 lweight of the machine ca.: 11400 kgdimensions of the machine ca.: 4700x2100x2700 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: tchamfer lenght: mmdistance between columns: mmControl: total power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mBrand: DurmaType: HAP 35200Capacity: 200 TBend length: 3.550 mmDistance between columns: 3.100 mmStroke: 185 mmMachine dimensions: 2.400 x 4.800 x 2.850 mm mmMachine weight: 13.300 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

offer 22460 Specifications: - Printing capacity 120 t - Working width 2520 mm - Passage between stands 2150 mm - Table width 220 mm - Projection 240 mm - Installation height approx. 400 mm - Ram stroke 160 mm - Working height approx. 900 mm - Engine power approx. 11 kW - Oil filling approx. 120 l - Space requirement approx. W 2750 x H 2600 x D 1900 mm - Weight approx. 7000 kg - with: - Swivel arm – control panel - Digital displays for offset -Mot. Backgauge with display - Universal die, split sharpening tool - Two-hand control panel, foot switch, 2 support arms

pressure: 125 tchamfer lenght: 3550 mmdistance between columns: 3050 mmcolumn arm: 300 mmstroke of ram: 240 mmquantity of oil: 200 lrated current: 27 Atotal power requirement: 11 kWweight of the machine ca.: 14000 kgdimensions of the machine ca.: 5675X3040X2900 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 125 tchamfer lenght: 3550 mmdistance between columns: 3050 mmcolumn arm: 300 mmstroke of ram: 240 mmquantity of oil: 200 ltotal power requirement: 11 kWweight of the machine ca.: 14000 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 175 tchamfer lenght: 4050 mmControl: DNC 1200 PS weight of the machine ca.: kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 320 tchamfer lenght: 7250 mmdistance between columns: 6550 mmControl: throat: 400 mmram - range of adjustment: 270 mmstroke: 270 mmtable surface area: 7250x400 mmdayligth: 560 mmfence: 5-1000 ja /neintotal power requirement: kWweight of the machine ca.: 53 tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 110 tchamfer lenght: 2550 mmquantity of oil: 390 lThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 150 tchamfer lenght: 3550 mmdistance between columns: 3050 mmControl: Cybelec DNC 880S stroke: 700 mmthroat: 350 mmweight of the machine ca.: ca. 15.000 kgheight of the machine: 3.900 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Description: Year of construction 1989 Pressure 150 t Bending length 4050 mm Stand width 3050 mm Stand projection 350 mm Installation height 430 mm Piston stroke 220 mm Table width 300 mm Oil content 390 liters Pressure output 265 bar Total power requirement 18.5 kWweight approx.: 13,000 kg, Approx. Onsite Dimension. (l x w x h): 4,900 x 2,740 x 3,310 mm