rubber machines used for sale (414)

Herman Schwabe Die Cutting Shaping Press Mechanical Press Model DG-HD Platen size 770mm x 1000mm Die cut shapes Manual cut / load pressure 4" stroke, 7" bore, 10 H.P. Motor, 415 volts 50 cycles 3 phase 14.84 full load current Made in Brooklyn, New York Serial number 50367 Complete with starter Overall dimensions 1.2m x 1.5m high x 3.3m long

1. LBBC Autoclave (AC3) Working diam. 600mm (2ft) Working: 1500mm (5ft) Max. working pressure 100 PSI 2. LBBC Autoclave (AC3) Working diam. 750mm (2ft.6”) Working: 1200mm (4ft) Max. working pressure 80 PSI

Schubert Press The platen size is 1390 mm (52”) x 2490 mm (98”) Electric heaters Make - Schubert Daylight – 305mm Floor standing Total number of rams: 16 Ram diameter: 2 ¾” Working pressure 3500 PSI The overall dimensions are length 3850mm x width 1500mm x height 2200mm Operational The condition of the hydraulics and pump unit along with ram seals is good Spare seals maybe possible (video link available on request)

Reed 42" x 16" Two Roll Mill. 40HP Motor, with clutch brake. Friction ratio 1.1 Manual Nips. On one-piece steel bedplate.

Complete Line Consisting of 1.Sheet material unwind station (let off stand) 2. Iddon 1320mm x 450mm dia wide 4 roll inverted L calender manual nip adjustment, even speed gears, auto lubrication system with 45kW AC right angle drive motor and gearbox, Steam heated bowls up to 150c Bowl temperature monitoring system, fabricated bedplate. Overhauled in 2007 (by Iddon) with new side frame and rolls precision ground 3. Edge Trim - make: Mario Cotta 4. Guillotine - Make: Pasquato SNC 5. Wind up

Iddon Two Roll Mill 6” diam. x 12” wide Fully guarded and interlocked

1 x Farrel Pomini model F160 Banbury internal mixer, Original year of manufacture: 1980, but rebuilt in 2000 (very good condition), Chamber volume: 160L Net batch size: 120kg, With 2 wing type rotors, Rotor tips hard material coated and fully chrome plated Rotor speed max 50rpm, pneumatic hopper, hydraulic drop door, FYH dust seals, Unidrive gearbox, With 435kw DC variable speed motor and electrical controls (415V). Complete and in good condition.

1 x Farrel Banbury internal Mixer, Model 00C. Machine number: 91M7017, Year: 1992, Stainless steel jacketed swing side (drop door design). Maximum steam or water pressure 150psi, chrome plated two wing cored rotors with spherical roller bearings, gross capacity of mixing chamber 4.24 liters. 5" Diameter ram cylinder, maximum pressure 100psi. Chrome plated single slope V-bottom, stainless steel, pneumatically operated front door, F.Y.A. dust stops, oil seals, oil injector, thermocouple. With 65kw (87hp), 340/440 volt, 1500 rpm motor, reducer ratio 15:1. Unit mounted in an enclosed cabinet with a pull-out discharge drawer. Includes an operator panel. In good condition.

1 x Francis Shaw model K2A MK4 Intermix Machine number 11242.8, Year June 1994, NR2 rotors, Working batch volume 27 - 36 litres Drop door with linear actuator, SSA dust seals, Pneumatic hopper, Hansen semi unidrive gearbox, Rating 150kw, 1475/32rpm, With ASEA 152kW, 1510rpm DC variable speed motor and controls.

1 x Farrel Bridge Model BR lab banbury mixer, Serial no. 91M7000, year: April 1991, Chamber volume 1.5litre pneumatic hopper and swing side discharge door, David Brown gearbox, 30kW DC variable speed motor and controls. Fully guarded with Key interlock system. Complete and in excellent condition.

1 x Alpha Technologies Mooney MV2000e Viscometer software discs and operation manual are included. You will have to register the software. PC not available. In good condition.

1 x Wickert 500ton upstroke vacuum press, Type: WKP5000/5/3, Year of manufacture: 1997, Machine Number: 2885 with 500mm x 500mm electrically heated platens, sliding bottom platen with ejector table, Daylight: 340mm 400/690V, 50Hz, 22kW. Heaters 12.5kW, Pressure 300 Bar Fixed guarding to rear, SICK light curtain guards to the front. With Siemens S5 PLC controls. In very good condition.

1 x Werner & Pfleiderer model GK90-E intermeshing mixer, Original year of manufacture: 1989, Chamber volume 91 litre, Net batch weight: approx 71kg, PES #3 type rotors, pneumatic hopper, hydraulic drop door, GWK TCU. KWE GmbH full unidrive gearbox input speed 1500rpm, Output speed 48.5rpm with Thrige Electric 470kW, 1520rpm, 380V DC v/s motor, Complete with electrical controls and in good condition.

1 x Werner & Pfleiderer model GK90-E intermeshing mixer, Original year of manufacture: 1989, Chamber volume 91 litre, Net batch weight: approx 71kg, PES #3 type rotors, pneumatic hopper, hydraulic drop door, GWK TCU. KWE GmbH full unidrive gearbox input speed 1500rpm, Output speed 48.5rpm with Thrige Electric 470kW, 1520rpm, 380V DC v/s motor, Complete with electrical controls and in good condition.

Choice of 2 x Francis Shaw K7 MK3 intermix, Total Volume: 320L, Useful volume 210L, Order number: 6061/1 and 6061/2, Year of manufacture: Oct 1986, NR2 Rotors, SSA type dust seals, Hydraulic drop door with linear actuator, Pneumatic hopper, Zamech full unidrive gearbox, Type: WD263-22.5, ratio 22.5:1. with 1000kW, 990rpm, 6000V motor. Rotor speed 44rpm. With modern starter panel, but without operator controls.

Francis Shaw Extruder Screw diam. 100mm (4?) LD ratio 10:1 Roller Feed Brush DC Motor 100HP motor 1500rpm 460 volts Variable speed drive Complete with Control Panel

ECO TS10 Deflashing Machine Year 1991 +/-

Iddon HRX 4.5? (120mm) Cold Feed Rubber Extruder Year 1994 LD ratio 17:1 Bostock & Bramley Gearbox ABB Motor: 1994, 95kW, 1870 rpm, 419 amps, 360 volts With 1 x spare vacuum screw With Control Panel

1 x Berstorff GmbH 250mm strainer extruder, Year of manufacture: 1988, L/D ratio 7:1, power roller feed (300mm wide), with 120kW, 1800rpm DC variable speed motor mounted on top of gearbox (belt drive), with tube head and knife at top for sheet extrusion. Complete with control panel etc and in very good condition.

Type; AUMA 15SN X 1600 Manufacturer: Berstorff, Germany Year of manufacture: 1998 Technical Specification: Working width: 1600 mm Steel belt width: 1750 mm Steel belt thickness: 1,8 mm Steel belt length: 15600 mm Rolls width: 1950 mm Center distance between frames: 2330 mm Heating roll diameter: 1500 mm Stretch rolls (I, II, III) diameter - 1000 mm Vulcanizing time: 1?30 min Working speed: 7?.210 m/h Max steam pressure in heating roll: 13 bar Max steam pressure in lower stretch roll: 8 bar Surface temperature of: Heating roll: ca. 195oC Lower stretch roll: ca. 175oC Pressure in heating zone between steel belt and rubber: 60 N/cm2 Main motor speed: 1 450 min-1 Drive position: Left from inlet Paint: RAL 6011 Air supply: 6 bar Cooling water supply: + 25oC Max hydraulic pressure Belt pressure tension: 250 bar Belt pressure regulation: ...

1 x Buzuluk 240 litre Internal mixer Model: 14630, year: Dec 2008 (body and hopper), Batch size: 200 kgs, Drilled sides, Self sealing type dust seals, Oil injection, Hydraulic drop door with linear actuator and toggle latch, Stellite faced drop door, Two wing tangential rotors. 20in pneumatic hopper. 3 zone TCU Full unidrive gearbox (Make Skoda), with 630kW, 6000V, 739rpm, 73.5A slip ring motor and Oil filled starter. In very good condition.

1 x NEW 'Bainite' (India) Make 1000mm (42in) wide x 400mm (16in) dia two roll mill, Hydraulic nip adjustment (dual acting cylinders), Peripherally drilled chilled cast iron rolls (Hardness 65/72 Shore), with anti friction roller bearings, Friction ratio 1:1.08, Hinged guide plates, Lubrication system comprising pneumatic intensifier with grease reservoir, Electro pneumatic brake with power fail safe mechanism. Safety bars fitted to front and rear. Compact right angle drive with 45kW Siemens AC variable speed squirrel cage motor through heavy duty helical design direct drive reduction gearbox (SF 2), Back roll speed 18rpm/front roll 16.6rpm. All mounted on a compact design fabricated steel bedplate. Stainless steel tray underneath. Including electrical controls comprising Siemens G130 VFD drive and S7-1200 plc with HMI. CE marked, with full Technical file, Documentation and S ...

NEW Bainite model BMIM95 95 litre intermeshing type mixer Customs Tariff CN Code: 8477.8093 Manufacturer: Bainite Machines Pvt Ltd Net chamber volume: 95 litre Rotor speed: 6 - 60 rpm Rotor type: HP-5 design (intermeshing) Dust seals: SSA (self-sealing arrangement) Motor power: 420kW, 1000rpm AC motor, 3ph, 50Hz, 380/400V Discharge door: Hydraulic drop door with linear actuator and toggle latch. Two (2) J Type thermocouples mounted in door top as standard One (1) Single acting pneumatically operated oil injector Feed Hopper Assembly: Hydraulically operated Floating weight: single ?V? bottom type Gearbox: Full unidrive type with S.F. 2.25 Bedplate: Fabricated steel Ancillaries: Dust stop lubrication (1.5HP x 2), hydraulic pump unit (20HP) Three (3) Zone closed loop temperature control (TCU) Electrical Controls: Schneider make variable frequency drive (VFD) controls wit ...

Troester.200mm H/F strainer M/C Number 7175-71 L/D 6.5/1 Roller Feed 350mm. Hinged strainer head with hydraulic clamp. 125KW AC v/s motor. On single bedplate. With controls.

Werner & Pfleiderer model GK50UK internal mixer. Chamber volume 85 litre, Net volume: 60 litre (batch size approx 85kg), Tangential type rotors, Year of manufacture: 1971, Pneumatic hopper, Hydraulic drop door discharge with rotary actuator and hydraulic latch. Full unidrive gearbox (August Seegers), with Intermediate selectable 2 speed gearbox, 675 HP rating, rpm 1500/1340, Output 895rpm or 1340rpm. With 550kW, 980A, 1482 rpm motor (fixed speed) Rotor speeds - N895 = 51/47rpm, N1340 = 78/72rpm. Siemens PLC controls.

Mapelli 300ton downstroke hydraulic presses with vacuum, Type T300, year 1990, 4 column type, with pneumatic front guard, fixed guards to sides and rear, main ram dia 450mm, with pull back rams, single daylight 500mm, with 600mm wide x 700mm electrically heated platens. With hydraulic power unit mounted on top. Complete with controls etc and in good condition.

Colmec Italy 150mm dia coldfeed extruder, roller feed - 200mm wide, Screw length 2000mm, L/D ratio 13:1, with simple Spaghetti die/cutter assembly, jacketed barrel and cored screw for temperature regulation (no TCU's included). with 100HP, 1750rpm, 575V, 3ph, 60Hz AC motor (ex Canada) and controls. Fabricated bedplate. Screw height: 620mm. In very good condition.

1 x Repiquet 2550mm wide x 820mm dia 4 roll inverted L Calender, Machine type: CALANDRE 4 CYL DE 820 x 2550, Machine no. 70-C9-87 Motorised nip adjustment, Peripherally drilled rolls, High pressure hot water hearing Bush bearings with flood lubrication, Hydraulic pre-loading to all rolls, Roll bending and unbending on roll 4, Cross axis on roll 3 and 1. Automatic bank sensors/control + camera system Traversing unit for roll buffing or sand blasting. 'Citroen' unidrive gearbox, type: SPECIAL, order no. 50491, Power 140/240 C.V. Speed 1500/2250, Output 46/59 with individual motor to each roll- Roll 1 and 4 - 130HP, Roll 2 and 3 - 240HP, Max calender speed 120m/min. Dual embossing station with approx 25 x embossing rolls (+ 5 x rubber pressure rollers) In very good condition.

REP model V68 Y20W vertical rubber injection presses, Type G8, year 2003, Clamp force 4000kN, Platen size: 630 x 800mm, Distance between columns: 730/440mm, Daylight: approx 1000mm, Injection unit type Y2000, Piston dia 81.5mm, Shot capacity: 2000cm3, Injection pressure: 1500 Bar Top and bottom ejectors. O/a dimensions: 2950mm x 1410mm x 4800mm high, weight approx 12000kgs. Complete and in very good condition (not operated for over 2 years).

Comerio Ercole 1500mm wide x 550mm dia 4 roll inverted L calender. Peripherally drilled rolls (high pressure hot water heating), Motorised nip adjustment, Adjustable guides, Cross axis to roll 3, Unidrive gearbox with universal couplings. Motor power: Roll 1 and 4 - 50kW. Roll 2 and 3 - 60kW DC variable speed. Oil lubrication.