other machines for plastic used for sale (441)

FOIL SEALING MACHINE type TS 1000 C-2 Year of Build 1980, Machine No: 1748, for the production of bags made of suitable Polyethylene and polypropylene films Product: Tren suture bag Processing: single-lane or dual-use printed two-lane unprinted Working width: max. 1000 mm Section lengths: 80 - 600 mm Film thicknesses: 2 x 0.015 - 0.100 mm depending on the welding wedge design Working cycles (mech.): max. 150/min. depending on film thickness, type of film, film quality and Section length Film web speed: max. 35 m/min Power consumption: 4 KVA Nominal voltage: 380 V Nominal frequency: 50 Hz Control voltage: 220 V Cooling water consumption: approx. 42 l/h Paint: light grey according to RAL 7030

Mixers for plastic granules and powdered products. Completely in stainless steel. Mixing motor 4 KW. Mixing chamber with separator on load cells. Pre-tank on load cells. Vacuum pump AZO 4 kW.

Mixer for granules and powdered products Mixomat. Completely in stainless steel. Mixing tanks on load cells. Tegiloxane pump. Vacuum pump AZO 5.5 kW. Granulate gate valve NW 100.

Granule dryer for heating and drying hygroscopic plastic granules. Tank capacity 1200 l. Heating capacity 9 kW. Optionally available with air dryer AZO LE 400 K

Dry air dryer Granulate dryer for drying and heating hygroscopic granules. Capacity 600 l. Heating capacity 4.5 kW. Optionally available with dehumidifier AZO LE 600 P.

Semi-automatic drilling device for plastic parts This purely pneumatic drilling device is designed for repeatable drilling of small plastic parts up to approx. 40 x 200 x 40 mm with holes up to 3 mm. Specifications: - Linear axis travel 420 mm - Stroke approx. 30 mm - Height adjustment approx. 100 mm - With 2-hand release - Plexiglass protection on 3 sides - Emergency stop switch - Sturdy, mobile frame made of aluminium profiles - With 4 swivel castors, 2 of them with brakes - Overall dimensions approx. 1000 x 1000 x 1700 mm - Weight approx. 50 kg - With collet for drill bit 1.5 mm Expiration: - Setup: Adjust stop angle to part size - Setup: Alignment of cross table in X and Y - Setup: Set height adjustment to part height - Inserting the part - Triggering via 2-hand button and holding until drilling is completed - Removal of the finished part and placement  ...

Fully automatic hot stamping press Oropress Mechanical eccentric press with lift table Lift table as pneumatic sliding table 250 x 250 mm Fully automatic sequence, optionally triggered with foot switch for single stroke Heated press punch 120 x 200 mm up to 250 °C Safety grille Film Feed Unit Built in 1986

Plant complete with all the machinery and molds to produce plastic pots, saucers, cages and thermoformed pot holders of various types and sizes: from 40 cm. up to 1 m. Composed of: N1) 135 ton SANDRETTO plastic injection press N1) 135 ton SANDRETTO plastic injection press N1) 200 ton SANDRETTO plastic injection press N1) 300 ton SANDRETTO plastic injection press N1) 400 ton SANDRETTO plastic injection press N1) 5 pallets CAMPETELLA robot + labeller N1) 7 pallets CAMPETELLA robot + labeller N3) automatic stacking and coding lines N2) mold cabinets with drawers with a capacity of 1000 kg N1) refrigerator to cool water N1) freecooler to cool the oil N59) molds for flower pots

Base Machine is a OMSO DM44N 2-Lane Lid Machine, age 2004, L- Format in feed conveyor for feeding Vertical Lid Stacks, acts as an accumulator as well Auto feeding of Lid Stacks to the 2 x Universal Screw Denesters with suction Nipples Infeed conveyor with Vacuum to keep Lids in proper position Each Lane with PAGOmat 6HS Pressure Sensitive Label dispensers, with PLC Controls, manufactured by PAGOmat/ Fuji Seal, Switzerland Outfeed Conveyor to 2-Lane Lid Stacker 2-Lane Stacker, each Lane with 2 x Universal Helical Screws Main Drive with a variable frequency, AC-Synchronous Motor with a brake, with Microprocessor Controls Max. dia. of round Lids: Ø125 mm Max. dimensions of Rectangular & Oval Lids: 125 x 150 mm Max. height of Lids: 25 mm Speed with Oval Lids dimensions 120 x 130 mm: Single Lane 110 Lids/ min, Dual Lane 220 Lids/ min 400 V, 3 phase, 50 Hz

Electric surface press REITZ EHSP522 Pressing surface 200200mm Pressure 5 KN / 0.5 tons Suitable for surface bonding of plastics and composites. On request with: - Heating plate and temperature control - Load cells and gauges for use as test press

Data sheet heating press Oropress Pneumatic press 5 KN / 0.5 tons Press stroke 50 mm Adjustment of the clear height with handwheel and spindle, adjustable from 100 to 220 mm. With top heating plate 120 x 100 mm and temperature control, temperature up to 250 °C. Pneumatic two-hand control with triggering via Festo ZSB. Pneumatic sliding table 180 x 220 mm for loading outside the machine. Machine dimensions W = 1100 mm, L = 700 mm, H = 1850 mm Machine weight approx. 300 kg Movable on castors On request for an extra charge with second heating plate and temperature control at the bottom.

This haul-off machine, manufactured by Battenfeld Extrusionstechnik GmbH, is in the machine storage of Plastima Used Machinery. The machine, a model Haul-Off R630/6V, dates from the year 1990. Make: Battenfeld Extrusionstechnik GmbH Model: Haul-Off R630/6V Year of manufacture: 1990 Voltage: 380 V Power: 4,5 kW Pipe diameter max: 110 mm to 630 mm

Press screw REG-MAC for drying foils and fibres, and for compacting foam (e.g. polystyrene, EPS) Drive motor 55 kw

Comexi solvent-free laminating system Coating width = 1320 mm , Speed = 350 m/min, With 2 unwinders (turnstile) With 1 rewinder (turnstile) With Doypag vario mixer. Mixing plant 4 heaters Pre-treatment AFS corona type. G 60 S,

Rotor diameter: 500 mm Rotor width: 1200 mm kW: 30

This cooling tank from Primac is in machine storage at Plastima Used Machinery. The Cooling Tank is from 1994 and is in great condition. - Brand: Primac - Model: CV.2C. 125/6 - Pipe diameter max: 125 mm - Cooling length: 6000 mm - Year of construction: 1994

This Haul-Off machine from IPM is in the machine storage at Plastima Used Machinery. The pull bench is from 2005 and is in good condition. – Brand: IPM – Model: Haul-Off TR 400/6 – Year built: 2005 – Voltage: 400 V – Power: 10.94 kW – Pipe diameter max: 63 – 400 Ø (mm) – Additional info: Reinforced model for heavy pipes

Year: 2017 - technically efficient, ready to work - after full service - processing of 2 profiles - support table

EPS contour cutting line for the production of sloping roof, fillet and ridge panels, as well as freely programmable "contours". suitable for net block dimensions: 5300 x 1300 x 1300 mm. Version with oscillating panel cutting frame for the production of EPS sheets and special cuts. incl. block turner incl. automatic wire adjustment incl. trimming frame incl. plate chain conveyor incl. waste disposal incl. wire break detection (electronically controlled) incl. extensive documentation Visits are possible at any time by arrangement.

The mixer combines hot and cold mixing. After hot mixing, the material automatically enters the cold mixer for mechanical cooling. -hot tank 800 l. - cooling tank 2000 l. - hot stirring time from 6 to 10 min. - cooling time from 10 to 15 min. - engine power 110 kW The device is adapted to the production of WPC terrace boards. Components needed for the product, such as PVC and wood dust or MDF dust, can be combined.

WITH COUNTING STATION M. No.: 3.65-00001 Wiring Diagram No.: 8.62-00001 Equipment / Additional information: Consists of: -Infeed conveyor -Machine -Counting station -Discharge belt

IMMEDIATELY AVAILABLE - video link on request KA 550 CNC-DRILL CNC-controlled 3-axis sawing and drilling center for sophisticated production technology Encapsulated, compact machine - designed as a closed production island - no noise and no chips in the machine environment - large extraction connection for efficient chip extraction. (The machine is also supplied as a two-axis sawing center without drilling unit). Dimensionally accurate 90° saw cuts both in small series and in large series production. CNC control based on Windows® with touch screen and color screen, simple menu-driven programming with symbols, remote maintenance module. Absolutely burr-free precision sawing of all materials such as - various plastics such as PVC and polyamide - GRP (glass fibre reinforced plastics) - aluminium - bronze - wood - copper - brass and . Drilling (through holes and blin ...

M. No.: 12088 10 Performance: 125 cups per min. (gross) Consists of: -Destacker -Bottom label dispenser -Side label dispenser 1 + 2 and 3 + 4 -Station for finishing the gluing of the side labels (ironing system) -Control station with camera surveillance -Stacker with counter -Outfeed conveyor for finished product The machine can also label round cups (160-180°, around). Cup height: 120-130 mm

COVER LABELING SYSTEM (Zweckform with Schleuter label dispenser) Age : ca. 1990 Performance: 100 cups/lids per minute Equipment / Additional information: Consists of: - Stacker - Labeling unit - Stapler

M. No.: 24 Kom.No.: 551.3852 Colours: 6 Equipment / Additional information: Consists of: • Stacker • Printing machine • Cup feeding • Stapler Technical data Printing unit type DW 200-230 Plate cylinder diameter 200 mm Max. possible print image width 110 mm Number of print segments 4 pieces Max. cup rim diameter 130 mm Min. cup rim diameter 70 mm (55 mm) Max. print image unwinding (specific plate unwinding) (361 mm) / D 115 Max. cup height 130 mm Min. cup height 35 mm Max. bevel 10 degrees Production speed depending on cup size, quality and raw materials with UV drying up to 24,000 C/h El. connection value (machine, drying and stacking) approx. 35 KVA El. control with Siemens PLC / control station with 2-line display Voltage is 400V, 3 phase, neutral and ground. 50hz is the frequency.

COVER LABELING SYSTEM SCHLEUTER GU 2 DO WITH 2xSTATIONS FOR PLACING SPOONS M. No.: 12087 Performance: 90 lids per minute (spoon inserted diagonally) Consists of: - Stacker - 2xStations for placing spoons - Labeling unit - Delivery station

COVER LABELING SYSTEM SCHLEUTER GU 2 DU WITH CIRCULAR STATION FOR PLACING SPOONS RNA SRC-N-630-1R M. No.: 12086 Performance: 60 lids per minute Consists of: - Stacker - Circular station for placing spoons - Labeling unit - Stapler

- technically efficient, ready to work - after full service - motor power: 0,5 kW - disc diameter: 175 x 20 mm, 95 x 20 mm - pneumatic profile clamping

Year: 2004 - technically efficient, ready to work - after full service - contour milling machine (rounded corners)

BIZETA BZ3T4P/8 welding machine was built in Italy in 1989. The machine is designed to perform a very precise and accurate welding of materials such as PVC and polyester by subjecting the surface of the material to high-frequency energy. Electricity in the form of an electromagnetic field generates heat, which softens the material and fuses its layers together. At the end of the process, the BZ3T4P/8 welding machine with rotary table cools the material surface while holding it under a high pressure, resulting in the formation of a very strong weld. The total weight of the machine is 3400 kg. Technical parameters of the high frequency welding machine BIZETA BZ3T4P/8 - maximum welding force: 9000 kg - maximum punching force: 3000 kg - power: 22 kW - nominal operating frequency: 27.12 MHz - maximum electrode power efficiency at high frequency: 10 kW - number of work heads: 3, inclu ...