sheet metal working used for sale (3,241)

sheet width: 2520 mmplate thickness: 3.2 mm STcutting thickness max.: 5.0 mm ALcutting thickness max.: 1.5 mm VAno. of strokes: 34 Hub/mincutting angle: 1° 20 Gradback stop - adjustable: max. 1.000 mmwork height max.: 800 mmtotal power requirement: 7.5 kWweight of the machine ca.: 2100 kg New price approx. 21,000 euros Special price on request Machine was rarely used - good condition ()Furnishing:- robust / motorized swing-cut guillotine shears- Shatterproof, torsion-free steel welded construction- compact and clear mechanical design- ESTUN NC digital display - type E10-S- electro-motorized back gauge, adjustment via electric. Button- 1x hold-down bar- manual cutting gap adjustment- rear protective device (side protective grilles)- Selector switch for single and continuous stroke- 1x front side stop- 2x front support arms- 1x freely movable foot switch- original instruction manualThe da ...

sheet width: 1050 mmplate thickness: 4.0 mmthickness at Niro-steel: 3.0 mmdistance between columns: 1200 mmblade length: 1150 mmno. of strokes: 46 - 69 Hub/mincutting angle: 1.30 °Control: konv. oil volume: 100 ltr.total power requirement: 5.68 kWweight: 1100 kg From a maintenance workshop In good condition ()Features:- Robust electro-hydraulic sheet metal shear- Electric motor-driven backgauge Backlash-free ball screw for backgauge Travel speed 100 mm/sec- Electric cutting length limiter Cutting length limiter to increase the stroke rate per minute- Manual cutting gap adjustment (lateral adjustment)- Front support table with recessed grips- Front finger/interference guard- 1x side stop with T-slot and millimeter scale- 2x front support arms- 1x freely movable foot switch- Operating instructions (PDF)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

BYSTRONIC BySpeed 3015 laser cutting machine was built in 2005 in Switzerland by Bystronic Laser AG. The machine on offer has been regularly maintained throughout its service life and is in very good technical condition. BYSTRONIC BySpeed 3015 is an excellent solution for precise cutting of a wide range of materials, i.e. stainless steel or aluminum. Thanks to the use of a number of well-proven solutions, the machine is perfect for both unit and series production. Workpieces with a maximum length of 3000 mm and a width of 1500 mm are machined by a high-quality laser beam with a power of 4.4 kW. The beam is generated by a reliable source with the highest energy efficiency. The cutting head with a powerful drive, in turn, provides very dynamic operation and a feed rate of up to 169 m/min. All this is complemented by a robust design that maintains the highest stability during even the mo ...

PEDDINGHAUS Hydraulic 800 hydraulic punching machine was manufactured in Germany by Paul Ferdinand Peddinghaus GmbH. This highly reliable machine is used for the precision machining of angle bars and flat bars. It enables the punching of square and round holes in structural steel workpieces with a maximum thickness of 25 mm. The machining process is performed with a high press force of up to 80 tonnes by means of punches. The perfectly balanced design of the machine maintains excellent stability even during the most intensive challenges. All of this makes the PEDDINGHAUS Hydraulic 800 an excellent addition to industrial facilities and locksmith workshops. The total weight of the machine is approximately 1500 kg. Technical specifications of the PEDDINGHAUS Hydraulic 800 punching machine General data - maximum press force: 80 t (800 kN) - throat depth: approx. 200 mm - working heigh ...

sheet width: 3100 mmplate thickness: 2.00 mmthickness at Niro-steel: 1.25 mmno. of strokes: max. 36 Hub/mincutting angle: 0.9 Gradtable height: 800 mmtable width: 430 mmdistance between columns: 3200 mmback stop - adjustable: 5.0 - 750 mmengine output: 3.0 kWweight of the machine ca.: 1950 kgrange L-W-H: 3730 x 2070 x 1400 mmFeatures:- Robust / motorized swing-cut guillotine shears- Machine with manual material/backgauge Travel range 5.0 – 750 mm stop depth Analog position display Manual adjustment from the front - Break-proof, torsion-free steel welded construction- Compact and clear machine design- 1x hold-down beam Hold-down opens before the knife beam moves up No kinking of very sensitive sheets- Manual cutting gap adjustment- Integrated sheet metal holding system for thin sheet metal cuts- Sheet metal/cut material removal at the front (operator side)- 1x side stop with mm scale- ...

pressure: 50 tchamfer lenght: 1500 mmdistance between columns: 1220 mmControl: Cybelec DNC 1200 closing speed: 95 mm/minworking feed: 1-10 mm/secwork stroke: 156 mmoverrun time: 59 mstracking travel: 6 mmthroat: 200 mmdistance table - lower edge of ram: 301 mmtable width: 160 mmtable height: 850 mmx-axis: 550 mmtravel R-axis: +/- 50 Number of axles: 3 (Y, X, R) St.weight: ca. 3600 kgdimensions: mma lot of lower and upper toolsincl. work lightnew control in 2003: Cybelec DNC 1200The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

This 3-axis WAFIOS BER-35 tube bending machine was manufactured in 2008. It is CE marked and has completed safety-technical approval, ensuring compliance with safety standards. If you are looking to get high-quality tube bending capabilities, consider the WAFIOS BER-35 machine we have for sale. Contact us for further details.

sheet width: 2550 mm: 4 mmsheet thickness for stainless steel: 2 mmrear stop: 750 mmtotal power requirement: 7,5 kWweight of the machine ca.: 3050 kgdimensions: 3300 x 2230 x 1360 mmStandard equipment:- All-steel welded construction with static and dynamic frame rigidityframe rigidity- Direct drive with brake motor- Specially alloyed cutting blades- 750 mm motorized, digitally adjusted backgauge with ball screwsrecirculating ball screws- Manual blade gap adjustment system- Mechanical sheet clamping system with plastic base- Work table with insert plates- foot switch for single and repeat cutting cycles- 1 x squaring arm 1000 mm long with metric scale- 2 x 800 mm front material support arms- Front stop- Finger protection - front and rear covers- Rear light guards- CE declaration of conformityYoutube video link:https://www.youtube.com/watch?v=pCuKwtBIQto&ab_channel=BaestleinG mbHThe data f ...

sheet width: 2040 mm: 4 mmsheet thickness for stainless steel: 2 mmtotal power requirement: 7,5 kWrear stop: 750 mmweight of the machine ca.: 2600 kgdimensions: 2810 x 2230 x 1360 mmStandard equipment:- All-steel welded construction with static and dynamic frame rigidityframe rigidity- Direct drive with brake motor- Specially alloyed cutting blades- 750 mm motorized, digitally adjusted backgauge with ball screwsrecirculating ball screws- Manual blade gap adjustment system- Mechanical sheet clamping system with plastic base- Work table with insert plates- foot switch for single and repeat cutting cycles- 1 x squaring arm 1000 mm long with metric scale- 2 x 800 mm front material support arms- Front stop- Finger protection - front and rear covers- Rear light guards- CE declaration of conformityThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 4050 mmplate thickness: 8 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width - max.: 0280 mmcoil weight: 1,00 tcoil internal dia.: 290 - 570 mmcoil outside - diam. ca.: 1000 mm0: 42 U/mintotal power requirement: 1,10 kWweight of the machine ca.: tdimensions of the machine ca.: 1,30 x 1,00 x 1,45 mControl unit missingprovisionally connectedmechanical brakeThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gebraucht : WA0013 : 265 €: 1 : 835 mm: 80 mm: 12 mmmint conditionThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

3000 x 13mm with power back gauge and rear sheet supports

Offer 26088 Technical data: - Flat steel shears - Flat steel - 400 x 16 mm - or: 300 x 18 mm - Profile steel shears - L- and T-irons at 90° 130 x 12 mm - Square steel / round steel 40 / 40 mm - Notches - With square clinker for sheet metal up to approx. 13 mm - Latch depth approx. 70 mm - Latch width approx. 52 mm - Hole punch - Punching force approx. 60 t - Projection 400 mm - Stroke approx. 10 to 50 mm - Perforates in steel up to Ø 31 in 15 mm - E. Contact stop - various punches + dies - Drive 400 V / 5.5 kW - Space required: W 1100 x H 2000 x D 1700 mm - Weight approx. 2100 kg

Key data: 6020 mm, 1 mm

used hydraulic Jorns long bending machine, with 5 wide stand units, with SN 1.25 motor scissors, bending beam width 16mm, with emergency/stop rail, foot switch, Control on the swivel bracket OP, with resettable sheet metal supports in the lower beam Machine is repaired, checked, cleaned by a specialist and is then fully functional. Test run is carried out. Working length 6020 mm Sheet thickness max. steel 1.25 mm Sheet thickness max. aluminium 2.00 mm Sheet thickness max. VA 0.80 mm Projection 1000 mm Total power requirement 16 A Dimensions approx. 6800 x 1650 mm Weight 3200 kg Upper beam stroke (opening width) 200 mm Bending angle (max) 140 degrees Roller scissors yes Number of stands 5 pieces Insertion depth 1000 mm Color: Blue Machine number 9453-07

Key data: 2040 mm, 1 mm

used Schechtl hand-held guillotine shears, with hand back gauge, extendable from the front Sheet metal support, automatic. Hold-down Machine is repaired, checked, cleaned by a specialist and is then fully functional. Test run is carried out. Working length 2040 mm Blechstärke Stahl/Sheet thickness steel 1,25 mm Sheet thickness Alu 1.75 mm Blechdicke VA/Sheet thickness stainless 0.80 mm Farbe/Colour grün Machine Weight: 650 kg Dimensions/Space requirment 2442 x 756 x 1056 mm Cutting gap adjustment without Automatic hold-down Fixed cutting angle Backgauge min. 5 mm Back gauge max. 500 mm Maschinennummer/Machine number 8604

Press brake manufactured in 2002. This HACO PPM 30135 b features a pressing force of 135 tons and a bending length of 3100 mm. It is equipped with a power of 15 kW, ensuring efficient operation. If you are looking to get high-quality bending capabilities, consider the HACO PPM 30135 b machine we have for sale. Contact us for further details.

We offer a Schechtl folding machine in top condition with the latest control technology. You will receive an invoice with VAT. Shipping worldwide possible. The price quoted is net.

High-performance mechanical automatic punching machine with coil system for strip material processing in series production. Manufacturer: Kaiser Pressen Model: KSTU 3150-15 R Machine Type: Automatic Punching Machine Year of Make: 1994 Press force: 3150 kN Drive type: mechanical Stroke rate: 20 – 120 1/min Plunger stroke: 20 – 150 mm Plunger adjustment: 150 mm Table surface: 1780 x 1250 mm Plunger area: 1500 x 1000 mm Installation height: 565 mm Tool weight max.: 3000 kg Strip width: 30 – 800 mm Band thickness: 0.5 – 3 mm Max. strap thickness: 4 mm Strip infeed height: 160 – 260 mm Belt speed: 4 – 30 m/min Straightening rollers: 9 pieces Feed accuracy: ± 0.1 mm Coil inner diameter: 508 mm Coil outer diameter: 1000 – 1500 mm Supply voltage: 3 x 400 V Air pressure: 5 bar Location: Radeberg

Key data: 4040 mm

used Schechtl manual bending machine, with roller shears Machine is repaired, checked, cleaned by a specialist and is then fully functional. Test run is being carried out Working length: 4040 mm Sheet thickness steel: 0.80 mm Sheet thickness aluminium: 1.25 mm Sheet thickness front: 0.50 mm without backgauge Colour: light grey Dimensions: 5013 x 750 x 1300 mm Machine weight: 2230 kg Roller shears: HA 400 RSL with cutter for cutting to length Opening width: 120 mm with underbeam adjustment without backgauge # Machine number HA 2774

Highest sheet capacity at 400 N/mm2 x 1000x2 16 A plug Length 1.30 m Width 0.4 m Height 1.30 m Weight 250 kg Tools

Working hours laser on: 50921 h Working hours beam on: 21717 h Laser power: 3200 Watt Working range laser: 4000 x 2000 x 115 mm Max. steel: 20 mm Max. stainless steel: 12 mm Max. aluminium: 8 mm Length: 11600 mm Width: 5300 mm Height: 2200 mm Machine weight: 16000 kg Electrical connected load: 73 kVA

Working hours machine: 23304 h Working hours laser on: 22804 h Working hours beam on: 10185 h Laser power: 4400 Watt Working range laser: 3000 x 1500 mm Max. steel: 25 mm Max. stainless steel: 20 mm Max. aluminium: 12 mm Length: 12800 mm Width: 6300 mm Height: 2400 mm Machine weight: 15000 kg Electrical connected load: 51 kVA

Decoiler Coil weight: 2 x 2 ton Material width: 380 - 500 mm Coil exterior diameter: 1.300 - 1.400 mm Expansion range: 445 -530 mm Leveller / Straightener Material width : 40 - 500 mm Number of levelling rolls: 7 pcs. Diameter of the levelling rolls: 60 mm Number of pinch rolls: 2 pcs. Diameter of the drawing rolls: 60 mm Number of pull out rolls: 2 pcs. Diameter of the pull out rolls: 60 mm Material thickness: 0,4 - 1,6 mm Cross section: 800 sq mm Feeding speed: 0 - 30 m / min Required power: 3 kW

Coil weight: 500 kg Material width: 41 mm Coil exterior diameter: 1.000 mm Expansion range: 250 - 500 mm Speed: 20 m / min Required power: 0,5 kW Dimensions L x W x H: 1.000 x 850 x 1.700 mm Weight of machine approx.: 200 kg

sheet width: 3100 mmplate thickness: 6.35 mmthickness at Niro-steel: 4.00 mmcutting angle: 0.5 - 2.5 °cutting gap adjustment: 0.05 - 0.8 mmno. of strokes: 12 - 50 Hub/minback stop - adjustable: 1000 mmControl: DELEM DAC 360 oil volume: 120 ltr.engine output: 9.5 kWweight: 7000 kg.range L-W-H: 3950 x 1950 x 1680 mm well-maintained condition () equipped with new DELEM control unitEquipment:- electro-hydraulic, guided plate shear- DELEM CNC control unit type DAC 360 front control panel, swiveling front left- Electro-hydraulic cutting angle adjustment- Electro-hydraulic cutting gap adjustment- electro-motorized backgauge, with ball screws- 1x extra-long side fence with T-slot mm scaleThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Used Hydr. Adira press brake with CNC controlled crowning WILA Scope of delivery: without tools LazerSafe Security System/CE Foot pedal Two front support arms 500mm, movable Table crowning: WILA motorized Special features: patented HEXA-C frame: low-torsion and therefore very accurate Hydraulics in semi-hybrid equipment very energy-saving because the engine is in the Idle only runs at 5Hz The bounce during start-up and descent is controlled by two high-precision servo valves Two linear encoders ensure accurate positioning of the press beam Adjustable guide of the press beam made of self-lubricating material Electrics and hydraulics with surge protection X&R axis run on backlash-free ball screws driven by servo motors 2 manual stop fingers Z axis Machine rear secured with light barrier AD 60 CNC control type Adcontrol 2 D Machine is repaired, check ...

Roll bending machine manufactured in 2020. This MG MG4R1520C features a working width of 1,550 mm and a bending capacity of 20.0 mm. It includes a CNC TouchCommand EVO control for enhanced precision and efficiency. If you are looking to get high-quality bending capabilities, consider the MG MG4R1520C machine we have for sale. Contact us for further details.

plate thickness: 3 mmangle adjustable from - to: 30 - 120 Gradtable height: 900 mmweight: ca. 800 kgCutting capacity: 3 mm St40 at 150 x 150 mm, 2 mm stainless steel, cutting angle continuously adjustable from 30° to 120°, pneumatic clamping for angle adjustment (Boschert system), machine is in good conditionThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.