sheet metal working used for sale (3,291)

Standard equipment: - Hi-Las high-pressure cutting - Laser cutting head with 5 lens - Laser cutting head with 7.5 lens - Cutting head quick-change device - Autom. Sheet metal outer edge detection - Position laser diode - progr. Cutting Gas Selection/Pressure Adjustment - Microweld - PMS Plasma Sensors - Sprintlas - ContourLas - AutoLas Plus - Oil spraying device - Autom. Pallet Changer - Work area lighting - Conveyors for small parts/waste - Multi-chamber extraction - Compact dust collector - Automatic switch-off - Safety devices - ToPs 100 lite -RJ 45 network connection - 3.5 floppy disk drive

Key data: 3500 mm, 12 mm

Schäfer SVRM 3500/12 - CNC 4-roll bending machine - Siemens CNC control with joystick for roller positioning and digital display (renewed in 2006) - Hydraulic tilting of the upper roller by control panel - Rollers made of quenched and tempered material with a strength of 900 N/mm² - Year of construction 1989 Technical data - Max. sheet width: 3500 mm - Bale length of rollers: 3550 mm - Max. sheet thickness bending: 12 mm - Max. sheet thickness bending 4xS/3xS: 8 / 6 mm - Max. insertion limit of the sheets at 20% work hardening: 380 N/mm² - Upper and lower roller diameter: 360 mm - Side roller diameter: 290 mm - Smallest radius to be achieved: 220 mm - Feed speed lower roller: 200 mm/min - Feed speed side rollers: 700 mm/min - Total installed capacity: 22 kW - electr. Control: 380 V / 50 Hz / 3 Ph - Machine weight: 21100 kg

BUD-MASZ slitting and cut-to-length line was built in 2011 in Poland by P.W. BUD-MASZ MACIEJ STACHLEWSKI. The system enables the precise cutting of material with a maximum thickness of 2.5 mm into both sheets and strips of equal width. The entire process is performed fully automatically. The material is uncoiled gradually towards the workspace, inside which there are, among others, high-quality roller knives and a transverse guillotine. The use of these components guarantees the highest cutting precision with optimum utilisation of the raw material. Once the cycle is complete, the sheets are taken out of the workspace by means of a lift table. In the case of slitting, the finished strips of material are wound back onto the coils. All this makes the offered BUD-MASZ slitting and cut-to-length line the best choice for any industrial plant. The coil slitting line is fully complete and co ...

BPR BA 35 Asymmetrical CNC tube and profile bending machine with 3 driven rolls Factory REMANUFACTURED, RETROFITTED and UPGRADED in 2020. AS-NEW CONDITION MACHINE ! Contact: info@roce.hr / roce.strojevi@gmail.com Reason for Sale: Very low operating hours. Stored for years as a properly packed backup machine. In 2020, it was sent to the original manufacturer for full factory refurbishment and modernization (although fully functional at the time). After refurbishment, it was again kept in storage as a reserve unit. Now sold only because it is no longer needed as backup capacity. Excellent condition. Ready for immediate use. Description: This CNC-controlled profile bending machine is designed for complex bending operations with continuous radius variation. It allows choice between automatic and manual operating cycles, providing flexibility for different produc ...

BUD-MASZ slitting and cut-to-length line was built in 2005 in Poland by P.W. BUD-MASZ MACIEJ STACHLEWSKI. This system enables precise cutting of material into both sheets and strips of equal width. Material with a maximum thickness of 2 mm is uncoiled gradually towards the workspace, inside which there are, among others, high-quality roller knives and a transverse guillotine. Cutting is performed by means of reliable components, which guarantee the highest cutting precision with optimum utilisation of the raw material. Once the cycle is complete, the sheets are taken out of the workspace by means of a lift table. In the case of slitting, the finished strips of material are wound back onto coils. The BUD-MASZ slitting line weighs 45 tonnes. The coil slitting line is fully complete and consists of the following components: 1. mechanical sheet metal decoiler 10 t 2. coil lift table 10  ...

BAYKAL RGS 3150x3 electromechanical guillotine shears were built in 2007 in Turkey by BAYKAL MAKINA SANAYI VE TICARET A.Ş. The machine, distinguished by its high precision, is used for cutting of sheet metal with a maximum thickness of 3 mm. The machining process is performed by means of quality cutting knives with an adjustable gap between blades. The all-steel design, combined with a powerful electromechanical system, guarantees the highest cutting performance during even the most intensive challenges. The workspace is additionally protected by high-end light curtains made by FIESSLER ELEKTRONIK. All this makes the offered BAYKAL RGS guillotine shears an excellent choice for any industrial plant. Technical specifications of the BAYKAL RGS 3150x3 guillotine shears - maximum sheet metal thickness (Rm

Key data: 2500 mm, 1 mm

Schechtl guillotine shears 2500mmx1.25mm in good condition with new knife and hand depth stop and foot switch. You will receive an invoice with VAT and net price. Shipping available worldwide. for questions Watsapp 0049(0)1607838365

sheet width - max.: 1020 mmplate thickness: 1,5 mmcutting length: 1020 mmweight: ca. 300 kgdimensions of the machine ca.: 1,3 x 0,8 mCondition: good, demo machine: Side stop: 600 mmMaterial place of deposit: ausziehbar Hand lever shears with counterweight, length stop, blank holder withQuick clamping, mm scale on the table, pull-out sheet metal support.Demonstration machine at a special price.Machine dealer with own stock of 1600 m².The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

tube diameter: 6 - 28 mmwall strength: 2 mmbending radius min.: 2 x D Control: IPU 20 bending radius max.: 5,0 x D mmbending angle max.: 190 °arbor length: 3000 mmoperating pressure: 180 barhydraulic motor: 4 kWweight of the machine ca.: 900 kgdimensions of the machine ca.: 3,8 x 1,1 x 1,3 mCondition: ready for operation: Video available on our website.: Electric 400 Volt: Bending segments: 15-20-26-28 mmBending mandrels: 4 Operation panel: 0,5 x 0,6 x 1,03 mDouble Foot pedal: Machine manual: Semi-automatic electro-hydr. mandrel tube bending machine with PLC control for 20 angles and display in the control panel for bending angle specification, angle detection and angle measurement via absolute value encoder, autom. tool plate reset, Turning device with digital display, hydr. quick chuck, aut.Mandrel lubrication, adjustable length stops.Operating modes: MANUAL and semi-automatic.Co ...

engraving field: 120 x 120 mmtable-size: 250 x 250 mmworkpiece weight: max 50 kgControl: Fobagraf machine weight ab.: 1000 kgmachine frame made of welded steel constructionCross slide, hard stone design, table top with steel stop ironHeight-adjustable laser headQuality-switched ND: YAG laser head, lamp-pumped, 100 WDeflection unit mounted on the laser head (with standard lens)Z-axis with gearbox and servo driveServo axis control with X-, Y-, and Z-axesWater-cooledControl: Fobagraf user software packageOperating system: Windows 2000operating hours: 17.388 hmanual includedThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 8749 Type: M2-3120B Producer: FLOW Created: 2011 Parameters: Table dimensions: 2000x3100 mm Spindle power: 6.6 kW

The machine is in good technical condition, testing is possible after prior agreement. Pressing force: 35 tons • Working length: 1250 mm • Control system: CNC (precise adjustment of angles and stops) • Condition: Fully functional, currently not connected. Main advantages: • High accuracy: Stable frame and precise positioning for high-quality bending. • Compact dimensions: Ideal solution even for smaller workshops and operations. • Accessories: The sale includes the equipment visible in the photos.

sheet width: 2540 mmplate thickness: 2 mmthickness at Niro-steel: 1,25 mmno. of strokes: 63 Hub/mincutting angle: 1,13 °table height: 750 mmtable width: 320 mmback stop - adjustable: 5,0-550 mmtotal power requirement: 3 kWweight of the machine ca.: 1300 kgEquipment:- manual backgauge, with analog display Adjustable from the front stepless adjustment over the entire travel range- 1x long side stop- 3x support arms- Free-moving foot switch- Sheet holding device for thin sheet blanksThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2540 mmplate thickness: 2 mmthickness at Niro-steel: 1,25 mmno. of strokes: 63 Hub/mincutting angle: 1,13 °table height: 750 mmtable width: 320 mmback stop - adjustable: 5,0-550 mmtotal power requirement: 3 kWweight of the machine ca.: 1600 kgEquipment:- manual backgauge, with analog display Adjustable from the front stepless adjustment over the entire travel range- 1x long side stop- 3x support arms- Free-moving foot switch- Sheet holding device for thin sheet blanksThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Offer 26008 Technical data: - 3 mot. driven rollers with asymmetrically hydr. Feeding of the two lower rollers - bends e.g. flat bars 100x40 flat up to Ø 600 mm - bends e.g. flat bars 100x20 upright up to Ø 800 mm - bends e.g. U 180x70 up to Ø 800 mm - Shaft diameter per 100 mm - Useful length of the standard shafts approx. 250 mm - Shaft rotation 5.4 rpm - Roller diameter 315 mm - Drive 400 V / 11 kW - With: - Separate control panel with digital actual value displays - Lateral straightening rollers manually adjustable - Standard bending kit for flat and angle material - Weight approx. 3500 kg - Space requirement approx. W 1600 x H 1700 x D 1600 mm

Key data: 6020 mm, 1 mm

with roller scissors and emergency stop rail Machine is repaired, checked, cleaned by a specialist and is then fully functional. Test run is carried out. Working length 6020 mm Sheet thickness max. steel 1.25 mm Sheet thickness max. aluminium 1.5 mm Sheet thickness max. VA 0.7 Projection 1000 mm Color: Green Total power requirement 16 A Dimensions 7000 x 1400 x 1400 mm Weight 3200 kg Upper beam stroke (opening width) 150 mm Bending angle (max) 140 degrees Roller scissors yes Number of stands 5 pieces Insertion depth 1000 mm Machine number 301644

sheet width: 3020 mmplate thickness: 5 mmdistance between columns: 3020 mmControl: Simatec OP7 stroke: 450 mmback stop - adjustable: 1000 mmwork height max.: 900 mmtotal power requirement: 22 kWweight of the machine ca.: 9000 kgdimensions of the machine ca.: 4200 x 1600/2900 x 2000 mmFeatures:- Motorized backstop, 1000 mm- Motorized upper crossbar adjustment- Motorized lower crossbar adjustment- Side protection- Foot switch- Operating instructionsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3000 mmplate thickness: 4 mmwork height max.: 900 mm: 450 mmtotal power requirement: 5,5 kWweight of the machine ca.: 4800 kgdimensions of the machine ca.: 4250 x 1500 x 1850 mmEquipment:- electric bending angle adjustment- electric upper beam adjustment- foot switch- operating instructionsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Offer 26018 Technical data: - Max. working length 500 mm - Max. sheet thickness 1.5 mm - Various roller diameters - Drive – brake motor 400 V / 1.4 kW - Space requirement approx. W 850 x D 1700 x H 1250 mm - Weight approx. 0.8 t - Roller attachments 42 ; 45 ; 50 ; 55 ; 60 ; 65 ; 70 ; 90 ; 135 mm

This HONESS V250-3000 was manufactured in 2002. A profile punching machine for tubes and profiles, it features a self-centering product clamp and interchangeable clamping jaws for various tube types. It can handle tubes up to 100 mm wide and 80 mm high, with a maximum punching diameter of 40 mm. Ideal for high-speed punching with a carriage travel speed of 40 m/min. Contact us for more information about this machine.

TRUMPF TruMatic 5000 R punching machine was built in 2001 in Germany by TRUMPF GmbH+Co. Maschinenfabrik. The machine has undergone regular maintenance and has been serviced on an ongoing basis throughout its lifetime. In 2025, among others, the oil pump, oil accumulators, head seals and transoms were replaced. The TruMatic 5000R is used for precision machining of both thick and thin sheet metal. All machining processes, i.e. punching and marking, are performed with a force of up to 22 tonnes on a large brush table. The table has been specially modified to handle sheets with a maximum length of 4 metres. Its design prevents any scratches or scrapes on the surface of the sheet metal as well as significantly reducing noise levels. The balls built into the table also facilitate the loading and unloading of workpieces. The TRUMPF TC 5000 R CNC punching machine is extremely easy to opera ...

Deep Drilling Machine brand Buck Year of construction 2000

Inv. Num. : 8956 Type: Easy Cut 6001.20PG Producer: MicroStep Created: 2006 Parameters: Control system: MSNC 500 Work table length: 6000 mm Work table width: 2000 mm Maximum sheet thickness when cutting: 38 mm Plasma source: Formica 163 W Machine weight: 2700 kg

Key data: 1020 mm, 2 mm

with bending rail 10 and 19 mm, additional segment insert for the upper beam (segment height 60 mm) and Material thickness adjustment, Machine is repaired, checked, cleaned by a specialist and is then fully functional. Test run is carried out. Working length: 1020 mm Sheet thickness steel: 2.0 mm Colour: green Machine weight: 350 kg Opening width: 150 mm Bending angle (max.): 130 degrees Machine number 16/9

Key data: 1020 mm, 2 mm

with angle stop, manually adjustable, with scales Machine is repaired, checked, cleaned by a specialist and is then fully functional. Test run is carried out. Working length: 1020 mm Sheet thickness steel: 2.0 mm Colour: grey Machine weight: 350 kg Dimensions: 1900 x 1150 x 1300 mm Hold-down manual Back gauge max. 500 mm Machine number 020607/010

Key data: 1020 mm, 1 mm

3-roll round bending machine, with wire inserts, seam groove, Machine is repaired, checked, cleaned by a specialist and is then fully functional. Test run is carried out. Working length: 1020 mm Sheet thickness max. steel: 1.25 mm Colour: green Weight: 220 kg Dimensions: 1290 x 600 x 1050 mm Number of round rollers: 3 pieces Roller diameter: 55 mm Machine number 1685

This Bystronic Fiber 4020 6KW was manufactured in 2015. It features a tool changer for sheet metal formats up to 2030 mm x 4030 mm and a 6kW fiber laser. The operator terminal is equipped with a touchscreen, USB interface, and runs on Windows XP. With low operating hours, this machine is ideal for precise cutting tasks. Contact us for more information.

- Max. nominal thickness 40 mm- Max. recommended thickness 20 mm- Max. bevel length in several runs 18 mm- Max. bevel length in single run 12 mm- MIn. bevel inner diameter 100 mm - X Bevel- K Bevel- V Bevel- Y Bevel- High average cutters lifespan around 1000 M- Self feed- Zero maintenace

- Max. nominal thickness 40 mm- Max. recommended thickness 20 mm- Max. bevel length in several runs 18 mm- Max. bevel length in single run 12 mm- MIn. bevel inner diameter 100 mm - X Bevel- K Bevel- V Bevel- Y Bevel- High average cutters lifespan around 1000 M- Self feed- Zero maintenace-  

Qty. 1 Second-hand complete Copper Strip Production Plant Mfc.: Shinkwang Tech, Waterburry Farrel, Rozai, Handuck, Mirae, Wuishi, Youngchang, Sundwig, Sonoda Eng., Wuxi Longar Mach., Backsan Mach., Deakwang Mach., Hankug Eng., Intrize, Samjung Built: 1960 – 2020 Material Width: 650 mm Thickness Entry: 12 mm Exit: 0.05 mm Consist of: Break Down Mill Intermediate Mill Finishing Mill Annealing Coil Built-Up Line Roll Grinder Pickling Degreasing Buffing Tension Leveller Slitters (3) Precious Slitter Drum Cutters (2) Scrap Shears (2) Cut-to-length (2) Packing Machine Draw Bench Machine