other metal working machines used for sale (10,914)

Broaching machine Karl Klink Technical data can be found in the photo

Manufacturer: PEAFFER Model: P160 H/I Power: 8 HP Voltage: 380 V Phase: 3 Frequency: 50 Hz Find more here - / Contact us at -

Measuring machine Zeiss Vista BJ 2008

CNC vertical machining center Type: VF-9 D/40 HE Manufacturer: HAAS Year: 2006 Control: Haas X: 2134 mm Y: 1016 mm Z: 762 mm Table: 2134 x 914 mm Max table load: 1814 kg Max spindle speed: 10000 rpm Through spindle cooling Machine weight: 12837 kg In good condition, fully functional, under power Find more here - / Contact us at -

Manufacturer: HAEUSLER Model: HPR 330 V+H Year of Manufacture: 2007 Approximately 10 pallets of tools for round bar processing are included, with diameters of 60.5, 137, 91, 168, 76, 51, 152, 129, etc. Condition : Machine currently not in use and therefore not fully assembled Technical Data: - Maximum bending moment (at 240 N/mm² yield strength): 200–330 cm³ - Number of bending rolls: 3 - Roll arrangement: asymmetric / symmetric - Roll diameter: 520 mm - Driven rolls: all 3 - Roll drive: hydraulic - Working speed: 0–7 m/min, stepless - Speed compensation between upper and lower rolls: automatic - Roll rotation reversal: electro-hydraulic - Adjustable bending rolls: 2 - Adjustment of bending rolls: hydraulic - Roll position display: digital, 0.1 mm accuracy - Roll bearings: roller bearings - Number of pressure roller systems: 2 - Adjustment of pressure roller systems: hydraul ...

Manufacturer: AGIE Model: FUTURA V 1PM Electrical Specifications: - Voltage: 400 V - Frequency: 50/60 Hz - Phase: 3 PH - Circuit Breaker Power: 17 kVA - Power Factor (Cos φ): — - Full Load Current: 15 A - Full Load Power: 3.9 kVA - Amp Rating of Largest Motor/Load: 3.4 A - Overcurrent Protection: 20 A @ 480 V ~, 18000 AIC Weight: 265 kg Condition and Maintenance: Last service performed at the end of 2021 (running hours: 9107). The machine has been used only a few hundred hours since. Overall in good condition. Find more here - / Contact us at -

Safan 2500 x 3 mmCutting length: 2500 mm Max sheet thickness st 45: 3 mm Max sheet thickness inox: 2 mm

GOM - ATOS III Rev.02.1 - 3D measuring device Condition: used, very good. Specifications: Camera system: 2 x 8,000,000 Camera pixels: 2048 x 2048 pixels (approx. 4 megapixels) Measuring field sizes XYZ: 150 x 150 x 100 mm to 2000 x 2000 x 2000 mm Measuring point distance: 0.075 mm to 1.0 mm Scanning time: about 2 seconds Measuring volume: 700 (incl. calibration plate) Blue Light Technology: Precise measurements regardless of ambient light. Including EDP and USB dongle Software version 2023 Incl. Tritop System (camera, 2x 1m scales, license) All in original cases With tripod, PC, rack, screen, small tools, reference points, 1x button Plug in and start working right away...

amount: 1 STKTool holderThese chucks are designed for high-speed machining.These are precision tools from the Italian company DAndreaThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Shaft bottom/top: 30mm/30mm, max. round tube length: 48mm, max. round tube diameter: 3mm, max. flat bar dimensions X/Y: 50mm/10mm, max. square tube dimensions X/Y/Z: 40mm/30mm/3mm, weight: approx. 200kg. Documentation available. An on-site inspection is possible.

Components: control cabinets, machine body (cabin, turbines, outlet, inlet), platform with processing unit and bunker, sound insulation cabin, impact box, bucket elevator, gratings, ladder, pre-impact box, small parts, piping, cable ducts, blasting media and refill silo, compressed air connection: 1/2 inch at 4–6bar, compressed air consumption: approx. 1.5m³/h, processed according to DIN ISO 8573-1, solid particle size: 1µm, density: 1mg/m³, water content: pressure dew point 3°C, oil content: 1mg/m³, length: 11,000mm, height: 5907mm. An on-site inspection is possible.

max. wheel diameter: 600 mmgear width: 500 mmmax. module: 15 min. module: 1 total power requirement: 2 kWweight of the machine ca.: 2 tdimensions of the machine ca.: 2x1,5x2 mThe rounding of the teeth is obtained by coordinating alternative movement of the cutter and rotary movement of the piece. The alternative movement of the cutter is obtained by rotating a cam, shaped in order to obtain radius or cusp rounding. A series of 4 cams allows to work modululus from 1 and 16 included. An regulation device allows change the modulus between the minimum and maximum value of every cam. The rotation of the piece is controlled by a three-stage gear wheel which forms the dividing system. The piece lock and the movement of the rapid entry of the cutter to the piece is controlled by pneumatic servo devices. The practicality and rapidity of the equipment, as well as the wide range of profiles availab ...

Manufacturer: Tox Pressotechnik Model: MAG 075.222.A.001 Year of Manufacture: 2008 Condition : Excellent Min./Max. Air Pressure: 0.3 / 0.5 MPa ; 3 / 5 bar Max. Press Force at Max. Air Pressure: 680 kN Total Stroke: 100 mm Power Stroke: 11 mm Machine Weight (without tool): 3420 kg Find more here - / Contact us at -

Manufacturer: ADIGE Model: LT652/B Year of Manufacture: 2002 Machine Description: - Tube laser system LT652, manufactured in 2002. - Equipped with a CO2 laser source with 2 kW power. - Loading length: 6500 mm - Unloading length: 3500 mm The machine is in good technical condition for its age. The cooling system requires occasional maintenance. Find more here - / Contact us at -

Fuchs extraction KKFD101F with silencer module and new filters ( activated carbon, HEPA , filter mat and filter bag ) without warranty; EXW, year of construction 11/99