presses used for sale (1,810)

FEINTOOL GKP F 100T fine blanking press was manufactured in Switzerland in 1974. The machine, distinguished by its robust, stable design, can perform several demanding machining steps in one precise process, saving time and labour. Workpieces with a maximum thickness of 6 mm thus achieve an extremely even surface and precisely defined edges that are impossible to achieve on other machines. The machining process can be fully automated when the FEINTOOL GKP F 100/160 hydraulic blanking press is retrofitted with a sheet metal feeder. The total weight of the machine is approximately 9 tonnes. Technical data of the FEINTOOL GKP F 100T hydraulic press - maximum workpiece thickness: 6 mm - maximum sheet metal width: 210 mm - total force including auxiliary functions: 160 t - shearing force: 100 t - hydraulic counterweight force (upper table): 1-40 t - hydraulic force of ring jaw (lower ...

Technical characteristics Nominal force, mc 1600 Not reach the slide to BDC, mm 12 Progress in the slide, mm 400 The frequency of continuous strokes, min-1 16 The highest frequency of single strokes, min-1 12 Closed height mm 870 Adjusting the closed height 220 mm Size slider, mm left to right 1600 front to back 1600 Dimensions plate, mm left to right 1600 front to back 1600 Power of main drive, kW 110 Dimensions, mm left to right 4670 aft 4670 height above floor level 8110 W 154 000kg

pressure: 100 tthroat: 345 mmstroke: 20-100 mmno. of strokes: 60 Hub/minram - range of adjustment: 85 mmtable surface area: 980x650 mmram surface: 600x440 mmhole in the table: Ø 200 mmtable height: 820 mmtool hole in ram: ¤7 65 mmweight of the machine ca.: 7 tdimensions of the machine ca.: 2000x2000x2900 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Effort 2000t moving matrix 280 mm landing pad 570 mm landing slider after closing the matrices 390 mm Number of moves of the ram, stroke / min 25 Electric motor power 160 kW Dimensions, mm: LWH = 856053604850, the level above the floor is 3200. Weight of the car without electricity: 239.8 tons. Weight of the bed: Front part: 82 tons. Rear part: 55t. Weight 270 ton

MAX CAPASITY 80 T

Key data: 75 t

Specifications: Capacity 75 tons Stroke rate 90 strokes Projection 300 mm Plunger stroke 16 - 140 mm Plunger adjustment 80 mm Table size approx. 800 x 600 mm Installation height max. approx. 400 mm

Capacity, ton 630 Stroke path till its position where it develops nominal capacity, mm 16 Slider stroke, mm 320 Slider strokes, spm 20 Max. distance between table and slider, mm 800 Distance adjustment between table and slider, mm 180 Table size, mm 1250 x 1250 Slider dimensions, mm 1000 x 1000 Opening in the table, mm 800 x 800 Thickness of bolster, mm 180 Cushion stroke, mm 130 Main motor power, kW 58 Machine dimensions, mm 3280 x 3470 x 6190 Machine weight, kg 55500

pressure: 55 tthroat: 200 mmstroke: 10-80 mmram - range of adjustment: 60 mmno. of strokes: 120 Hub/mintable surface area: 600x450 mmram surface: 290x230 mmtable height: 850 mmtool hole in ram: Ø 40 mmweight of the machine ca.: 3,5 tdimensions of the machine ca.: BxTxH 2000x2000x2700 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 40 tthroat: 195 mmstroke: 8-78 mmno. of strokes: 76-190 Hub/minram - range of adjustment: 60 mmtable surface area: 650x380 mmtable height: 840 mmhole in the table: Ø 110 mmram surface: 250x350 mmtool hole in ram: Ø 40 mmtotal power requirement: 3 kWweight of the machine ca.: 2,2 tdimensions of the machine ca.: BxTxH 1450x1220x2110 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 63 tthroat: 320 mmstroke: 8-100 mmno. of strokes: 120 Hub/minram - range of adjustment: 63 mmtable surface area: 730x600 mmram surface: 540x360 mmtable height: 850 mmtool hole in ram: Ø40 mmweight of the machine ca.: 5,5 tdimensions of the machine ca.: BxTxH 2000x2000x3000 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 100 tchamfer lenght: 2050 mmdistance between columns: 1550 mmthroat: 250 mmstroke: 200 mmadjustment of press crosshead: 200 mmstroke speed - idle stroke downwards: 105 mm/secstroke speed - idle stroke upwards: 180 mm/secstroke speed - under load: 9,5 mm/sectable width: 200 mmtable height over floor: 900 mmdayligth: 280 - 480 mmback stop - adjustable: 3 - 729 mmcontrol: CYBELEC SYNCHRO control: CNC 7400 PS total power requirement: 7,5 kWweight of the machine ca.: 10 tdimensions of machine L x W x H: 3,70 x 2,45 x 2,80 mAccessories: programmable back gauge, table extensions, various upper and lower dies segmentsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Offer 22564 Specifications: - Printing capacity 150 t - Working width 2600 mm - Passage between uprights 2100 mm - Table width 180 mm - Projection 250 mm - Installation height 325 mm - Drive 400 V / 7.5 kW - Space requirement approx. W 3000 x H 2400 x D 1600 mm - Weight approx. 7000 kg - With: - Two-hand control panel with foot switch

pressure: 25 tthroat: 200 mmstroke: 4 - 80 mmtable surface area: 595 x 410 mmram adjustment: 70 mmno. of strokes: 150 Hub/mintable adjustable in height: 240 mmtotal power requirement: 1,1 kWweight of the machine ca.: 1,45 tdimensions of machine L x W x H: 1,30 x 0,80 x 2,0 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Offer 20202 Specifications: - max. pressing force 35 t - Projection to the middle of the ram 240 mm - Working height adjustable with hand crank 540 to 940 mm - 2 Hand control - Protective shield enclosure with light barrier - Material - Slide-in device - Pneumatic connection - Press control via SIEMENS SIMATEC OP 7 - Drive 400 V / 15.5 kW - Space requirement approx. W 1200 x H 2000 x D 2400 mm - Weight approx. 2500 kg

Key data: 750 kN, 150 mm

Control: STE 328-89-1 1/2" complete TOX Powerhouse: S75.160.200.12D Table size: 996 x 695 mm Installation height: 600 mm Total stroke: 150 mm Power stroke: 10 mm Weight: 5700 kg Electrical connection 230 V

Inv. číslo: 4465 Type: PL-140 LC Výrobce: OMC Vyrobeno: 2014 Parametry: Příkon: 75 kW

echnical characteristics Nominal force, mc 1600 Not reach the slide to BDC, mm 12 Progress in the slide, mm 400 The frequency of continuous strokes, min-1 16 The highest frequency of single strokes, min-1 12 Closed height mm 870 Adjusting the closed height 220 mm Size slider, mm left to right 1600 front to back 1600 Dimensions plate, mm left to right 1600 front to back 1600 Power of main drive, kW 110 Dimensions, mm left to right 4670 aft 4670 height above floor level 8110 W 154 000kg

Inv. Num. : 6992 Type: LKT 250 Producer: METALPRESS Created: 1963 Parameters: Ram stroke: 120 mm Plunger adjustment: 100 mm Machine weight: 2700 kg

Key data: 400 t, 800 mm

Oil-hydraulic double-column press 400 T with sliding table Press type: Double column press Thermally neutral 80 – 120 °C Number of operating pages 1 page Forces Pressing force max. 4000 kN Free tear-off force max. 400 kN Print build-up time Closed tool steel on steel Max. 4 sec. Dimensions: 3,800 mm long and 4,475 mm wide Max. opening width 800mm Stroke 800mm Table height above floor 1100mm Height above ground (height) approx. 4300 mm Hall height min. 5500 mm Parallel deviation at 20°C +/- 0.1 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.2 mm/m Weight Total weight of the press without consumables and table top approx. 28 tons Press table Table size 1500x1500 mm Velocities Quick closing at 100 mm sec. Pressing speed 8 – 3 mm sec. Acoustic pressure Sound pressure level, measured at a height of 1.5m on the control pane ...

Nominal force: 6300 ton Number of continuous strokes per minute: 40 Ram stroke: 460 mm Distance between ram and table (table is in upper position): 1150 mm Table adjustment: 15 mm Distance between press columns: 1950 mm Ram dimensions: -front to back: 1680 mm; -left to right: 1680 mm Table dimensions: -front to back: 1950 mm; -left to right: 1920 mm Mechanical upper ejector: -max stroke: 100 mm; -number of positions: 1 -steps of stroke adjustment: 25-30-75 mm -force: 30 ton Pneumatic lower ejector: -max stroke: 300 mm -stepless stroke adjustment: 15-300 mm -number of positions: 3; -force: 65 ton Side windows dimensions: -width: 1100 mm; -height: 1280 mm Main motor: 400/590 kW/rpm Press layout dimensions: 6300x8965 mm Total height: 11125 mm Height above floor level: 9150 mm Total weight:  ...

2000 Ton Sumitomo Hot Forging Press line Year 2006 Stroke 350 mm (13.78") Strokes per min 75 Shut height 850 mm (33.47") SlideAdj. 7 mm (.27") Ram size 1200 mm LR X 1300 mm FB Bed size 1320 mm LR X 1300 mm FB 4 stage transfer system Slide knockout Bottom knockout Scrap System Dual Die Changer Extra Die Shoes Billet Heater and Billet Saw Also Available This line was used by HONDA to make transmission gears, It takes a billet, cuts it to size, heats it to 1300 C then the press hits it 4 times. It can determine good from bad parts, the bad parts get sent to a quench tank, the good parts get sent into a cool down conveyor that you can pick the parts up by hand at the end. The entire system was ran by one operator.

SPK KB 2132 eccentric press was manufactured in the USSR in 1980. Operating with a force of 160 tonnes, the press of almost indestructible design offers the highest quality and precision during the most demanding workpiece machining. The machine’s equipment includes among others a pneumatic clutch, a large-area slider performing up to 71 strokes per minute, central lubrication and manual control. The total weight of the press is 13200 kg. Technical data of the SPK KB 2132 press - maximum press force: 160 t - work table dimensions (L x W): 1000 x 700 mm - maximum slider stroke: 160 mm - minimum slider stroke: 25 mm - slider dimensions (L x W): 580 x 460 mm - slider adjustment range: 120 mm - slider stroke rate: 71/min - intermediate plate thickness: 110 mm - distance between work table and slider (slider in lower position, largest stroke, connector unscrewed): 480 mm - bore ...

Nominal force: 2500 ton Ram stroke: 190 mm Number of strokes in 1 minute: 20 Shut height: 800 mm Bolster plate-to-ram adjustable stroke: 15 Table size: 1250x1400 mm Weight 124.230T

Capacity: 1 200 T, Total stroke: 500 mm, Stroke of main crank shaft: 318 mm, Stroke of mobile die: 215 mm, Stroke/min: 27, Bar diameter: 50-90 (150) mm, Max diameter of peace: 152mm, Max weight of piece: 5 kg, Main motor power: 75 KW, Area of machine : 6400 x 4420 mm, Hight of machine: 3830 mm, Weight: 128.0 T

Nominal weight of the falling parts: 750 kg Max. number of blows per minute: 105 Kinetic energy: 1900 kg Distance from an axis of the slider up to bed: 750 mm Cylinder diameter: 600 mm Diameter of the plunger: 630 mm Max. headstock travel: 835 mm Dimensions: -Left-to-right: 3940 mm -Front-to-back: 1430 mm Height above floor level: 3260 mm Weight: -With an anvil-block: 25600 kg -Without an anvil-block: 16600 kg

Compressive force: 25 t Projection: 200 mm Table size: 450 x 600 mm Table adjustment: 240 mm Plunger adjustment: 70 mm Stroke adjustment: 4 - 80 mm Stroke rate: 150 rpm Drive motor: 380 V, 1.1 kW Space required: 1600 x 850 x 2000 mm Weight: approx. 1450 kg

pressure: 110 tthroat: 290 mmstroke: 20-124 mmno. of strokes: 60 / 90 Hub/minram adjustment: 85 mmtable surface area: ca. 920 x 590 mmram surface: ca. 530 x 280 mmdistance table to upper part of the press: ca. 450 mmhole in the table: ca. 180 x 300 mm mmtable height: ca. 750 mmtool hole in ram: Ø 50 mmNumber of working hours: 8214 hdistance table to upper part of the press: mmweight of the machine ca.: 5,5 tdimensions: ca. 2000 x 2000 x 2600 mmoverhauled by the manufacturer Helmerding in 2014 including conversion to new onespress safety control.Operating hours read since overhaul in 2014: 8214Documentation of press safety control availableelectrical grease central lubricationHydraulic clutch-brake combinationMechanical break plate in the ramtwo-hand operationfoot controlThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Capacity, ton 1250 Stroke, mm 500 Min number of no-load stroke: 8 /per min Slider adjustment, mm 215 Max. shut height between bolster plate and slider (stroke down, adjustment up), mm 1100 Table size, mm 1600 x 1850 Slider size, mm 1300 x 1400 Table gap size, mm 1100 x 1100 Distance between columns, mm 1630 Distance between slides, mm 1580 Cushion travel, mm 200 Cushion capacity, ton 200 main motor power, kW 90 Press weight, kg 110000

Stock Number: 3785 ECCENTRIC PRESS Manufacturer: PMB, Type: EPFT 100 Machine NO.: 004301, Year of manufacture: 2002 Specifications: Table size 780 x 590 mm Stroke length 8-120 mm Number of strokes per minute 55 Projection 300 mm Operating height 395 mm Total power 7.5 kW Pneumatic clutch. Gear ratio. Hydr. Overuse protection. Weight: 5500 kg