presses used for sale (1,810)

Nominal force: 2500 tons Slider stroke: 600 mm Slide strokes per min: 11 Distance between table and slider: 1500 mm Capacity of the main drive: 220 kW Table size: 2000x4500 mm Machine dimensions: 5910x8700x10355

pressure: 20 tthroat: 185 mmstroke: 100 mmtable surface area: 380 x 350 mmdayligth: 250 mmtable height over floor: 840 mmtotal power requirement: 4 kWweight of the machine ca.: 1,3 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 6701 Type: 4000 kN Producer: Hydraulico Created: 1977 Parameters: Control system: SIEMENS SIMATIC OP Compressive force: 4000 kN Stroke: 800 mm Table height: 680 mm

Inv. Num. : 6700 Type: 3000 kN Producer: Loire Created: 1992 GO 2008 Parameters: Control system: SIEMENS SIMATIC OP17 Compressive force: 3000 kN Table length: 2495 mm Table width: 1505 mm Maximum distance between the table and the ram (when the ram is low): 1200 mm Stroke: 800 mm Working speed: 64 mm/s

Universal stamping machine Max impact power 50 KN Total stroke 80 mm Stroke sequence per hour 1500 Pneumatic Data

Hand screw press, used Balancier, used Typ/ type: PSHZ 25/I Presskraft / rated pressure: 25 t Hub/ stroke: 250 mm Tischgrösse/ table size: 400x 500 mm Ram: 200 x 500 mm Tischöffnung / hole in table: 140 mm Weight/ weight: 0,9t

Rotary indexing table with 12 stations Automatic ejector three pressing stages Pressure capacity 1,000 KN Stroke 12-120 mm Stroke rate 30-60 1/min Plunger adjustment 80 mm Total weight 9,500 kg

Press Schüco Model 290124 Type 2 Specifications: •pneumatic • Operating pressure max. (bar): 8 • Weight max. (kg): 80 • Enclosed tool: included (see photos)

FEINTOOL GKP F 160 hydraulic press was built in Switzerland. The automatic fine blanking press combines several workpiece machining stages into one precise process and significantly saves time and effort. As a result of fine blanking, parts with a maximum thickness of 6 mm obtain a characteristic even surface and accurately defined edges that cannot be achieved with other machines. The FEINTOOL GKP-F hydraulic punching press features a robust, stable construction and a total force of 160 tonnes. Offered with the machine a sheet metal feeder with a maximum thickness of 6 mm and a width of 210 mm allows for completely automatic machining. The automatic punching press underwent extensive modernisation in 1999. The total weight of the GKP-F 160 press is 9000 kg. Technical data of the FEINTOOL GKP F 160 fine blanking press - maximum sheet metal thickness: 6 mm - maximum sheet metal wi ...

Here are the technical data of the offered machine: Technical data + information: • No-load speed up to 40 mm/sec • Opening speed up to 40 mm/sec • Starting press speed 5–15 mm/sec • Table size/heating plate size 600 × 600 mm • Plunger size/heating plate size 600 × 600 mm • 2 heating plates, electrically heated, up to 250 degrees – as OPTION • Total size approx. 2000 × 1000 × 2800 mm height • OIL temperature monitoring • Automatic lubrication • Free positioning of the plunger • SICK/LEUTZE light barriers 14.1 mm on the front • Circulating oil cooling • Pressure holding valve 0 to 1800 sec. • Rear monitored door • Pressure adjustment from 30 T to 120 T • Travel limitation either by pressure or position • Programming set-up mode, single stroke (adjustable via rotary switch) • Control panel permanently installed in the wall  ...

pressure: 160 tdistance between columns: 850 mmstroke: 150 mmtable surface area: 850x650 mmtotal power requirement: kWweight of the machine ca.: 7 tdimensions of the machine ca.: 2,5 x 2,5 x 3 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Specifications: Capacity: 160 t Passage between stand: 1100 mm Working area, max.: 1100 x 350 mm Piston stroke: 400 mm Flow speed: 6.2 mm/s Return speed: 6.8 mm/s Motor power: 5.5 kW Width: 1640 mm Depth: 1000 mm Height: 2550 mm Weight, approx.: 1300 kg Equipment: - Laterally movable cylinder via rack, pinion and handwheel - Spacious work area - Height-adjustable table - Torsion-resistant design with welded steel -Manometer - Fine adjustment of pressure - Additional hand pump

Specifications: Capacity: 100 t Passage between stand: 1010 mm Working area, max.: 1010 x 300 mm Piston stroke: 400 mm Flow speed: 7.12 mm/s Return speed: 13.42 mm/s Motor power: 4 kW Width: 1600 mm Depth: 850 mm Height: 2450 mm Weight, approx.: 1000 kg Equipment: - Laterally movable cylinder - Spacious work area - Height-adjustable table - Torsion-resistant design with welded steel -Manometer - Fine adjustment of pressure - Additional hand pump

Specifications: Capacity: 60 t Passage between stand: 820 mm Working area, max.: 820 x 300 mm Piston stroke: 400 mm Flow speed: 6.1 mm/s Return speed: 10 mm/s Motor power: 3 kW Width: 1460 mm Depth: 850 mm Height: 2400 mm Weight, approx.: 700 kg Equipment: - Laterally movable cylinder - Spacious work area - Height-adjustable table - Torsion-resistant design made of welded steel -Manometer - Fine adjustment of pressure - Additional hand pump

Type / type: N 25 Year of make: 1977 Manufacturer / make: Weingarten Rated pressure: 25 t Number of strokes: 140 / min Radius slide center to frame: 200 mm Window in frame: 240 mm distance table slide: 250 mm Stroke adjustment / adjustment of stroke: 8 ... 80 mm Ram adjustability/adjustment of ram: 50 mm Ram size / surface of ram: 355 x 220 mm Table size / surface of bed: 560x 400 mm Hole in table: 160 mm Power of main motor:3 kW Weight / weight: 2,23 t

Capacity :10 tons, Weight of falling part,nominal mass of drop parts without upper instr.:9 tons, Effective working kinetic energy after blow :25000 kg mtr., Max. working ram stroke :1400 mm, Max no of blows : 30/min , Distance between slides : 1000 mm, Shut height : 775 mm , Ram size front to back :1200 mm, Bolster size front to back :1200 mm, Air pressure : 7-9 MPA , Height of instruments : 450 min., Die-holder front to back dimensions: 1400 mm, Height above floor level: 7270 mm, Hammer dimensions : 4400x10420x2700 mm, Weight (less anvil block): 73.5 ton, Weight of anvil block : 203.8 tons.

Used SMG HZPUX 350/200 - 1500/1300 moulding press in good condition! Main technical data: - Power: 510 ton - Maximum span with castle: 1460 mm - Minimum light with castle: 520 mm - Maximum span without castle: 2160 mm - Minimum light without castle: 1220 mm

Nominal mass of falling parts, taking into account the mass of the upper stamp (500 kg.), Kg. 5000 Actual mass of falling parts without top stamp, kg. 5030 Effective kinetic energy of falling parts at full successive impacts, kgc m 12500 The greatest working stroke of a woman, mm. 1300 The smallest height of dies without shanks, mm. 400 Distance between guides in the light, mm. 800 The length of the woman in the direction perpendicular to the front of the hammer, mm. 1180 Steam (air) pressure before entering the cylinder, atm. 7-9 Nominal mass of the upper die, kg 500 The largest mass of the upper die, kg. 1500 The highest permissible steam temperature, ⁰C 200 weight 145-148ton, weight of anvil block 75+22 ton.

Eccentric Press Brand Ebu Type EP15 Table size 400x430mm Max pressure 15 000kg Table height adjustment Table passage D160mm Stroke adjustment 4-70mm Ram bore 40mm Projection 200mm Max distance table-tappet 320mm Single/Duration Stroke Shield Flywheel D600mm 400V 1.0kW Machine weight ca. 870 kg The purchase price is net. Can be viewed and tested in our warehouse. Delivery is possible at an additional cost. All information without guarantee!

Used press for crown corks CALLAHAN. Very good working condition. Sizes of the sheets 896x734 mm. Short crown corks - 6,00 mm.

Stock number: 3768 CNC PRESS BRAKE Manufacturer: DONEWELL, Type: 100 x 3000 Machine NO.: 588 12 2348, Year of construction: 1988 Specifications: Size bending length 3100 mm Size Printing capacity 100 tons Stroke length 215 mm Stand passage 2600 mm Projection 265 mm Bending speed 420 mm/min Hydraulic. CNC control Cybelec EURO III Fabr. Controlled in Y1-Y2-X Achen Program-controlled backgauge. X - 500 mm Accessories: Segment-split upper tool 3100 mm Multi bottom tool 3100 mm Operating manuals Length: 1300 mm, Height: 2450 mm, Width: 3100 mm, Weight: 7000 kg

Standard Equipment's Chrome Coated Cylinder Boiled Steel Body Pressure indicator Pressure Adjustment User guide 2 Years Warranty CE

Pressing force 1000 kN Table size 750 x 560 mm, diarrhoea opening 100 mm Installation height 800 mm, stroke 500 mm Projection 360 mm Bear size 530x400 mm, 2 T-slots Ram speed: down 200 mm/sec, up 400 mm/sec Connection load approx. 21 kW Incl. Feeder WE16 for 160 mm bandwidth Coil tray and straightening unit Fabr. OFFICE; Type CA200/R40-7, YOC 1994 Reel, loop control Two-hand operation Manuals

Capacity, ton 1250 Stroke, mm 500 Maximum drawing depth,mm 200 Min number of no-load stroke: 14 /per min Slider adjustment, mm 315 Max. shut height between bolster plate and slider (stroke down, adjustment up), mm 1250 Table size, mm 1600 x 1800 Slider size, mm 1530 x 1800 Aperture in a table, mm 1100 x 1100 Distance between columns, mm 1600 Cushion travel, mm 200 Cushion capacity, ton 200 Maximum push force ton 31.5 main motor power, kW 125 Press overall dimensions: 5850x3100x8950 mm Press weight, kg 195000

Maximum force ton-force 400 Slider stroke length mm 250 Slider stroke length to lower position mm 12 Slider strokes per minute 25 Number of single turn-on 19 Maximum distance between table and slider (in lower position of slider) mm 510 Adjustment mm 160 The sizes of a under-forginig plate mm 1000 Table overall dimensions: mm - from front to rear 1000 - from left to right 1000 The sizes of an aperture in a table mm 630 Slider overall dimensions mm 800 x 800 window dimensions in cheeks mm 600 Total power of electric motors kW 43,3 Press overall dimensions mm - length 3470 - width 3140 - height 5940 Press weight without hydropneumatic pillow kg 31 400

Nominal effort: 630 tons Course stroke: 420 mm Number of strokes in a minute: 20 Bolster plate-to-ram adjustable stroke: 180 mm Max. distance plate-to-ram (in lower position of slider): 750 mm Slider dimensions 1000x1000 mm Table size: 1250x1250 mm Dimensions of the hole in the table 800x800mm Thickness of the sub-stamp plate 180 mm Height above floor level 600 mm Main motor power: 56 kW hydropneumatic pillow in the table Press overall dimensions: -Length: 3280 mm -Width: 3470 mm -Height: 6190 mm Press weight: 52650 kg

Capacity, ton 1000 Slider stroke, mm 400 Unattainable stroke, mm 12 Slider strokes, spm 20 Shut height, mm 730 Distance adjustment between table and slider, mm 200 Slider size, mm 1200 x 1200 Table size, mm 1250 x 1250 Table gap size, mm 800 x 800 Bolster plate thickness, mm 260 Pneumatic cushion capacity (eject), ton 40 Pneumatic cushion stroke, mm 160 Pneumatic cushion load, kg 4500 Main power drive, kW 75 Voltage, V 340 Machine dimensions, mm 4310 x 3820 x 6790 Machine weight, kg 77100

Hydraulic press brake Manufacturer: MENGELE Type: A 100-2 Pressing pressure: 100t Stroke: 160mm electr. Connection: 400V 3Ph Year of construction: 1964 Condition: used and functional

Hydraulic press

immediately available CNC press brake YAWEI PBH160/3100-4C - Pressing force: 1600KN - bending length: 3100mm - Year of construction 2022 - CNC controlled hydraulic crowning - Cybelec Modeva 19T control - WILA upper tool clamping - 60mm table with 13.5mm x 22mm groove for insertion matrices - 2 front support arms movable on linear guide - CE with Fiessler AKAS IIF (automatic height adjustment) - 24 months warranty - Commissioning, training