presses used for sale (1,637)

pressure: 1000 tdistance between columns: 4150 mmstroke: 1200 mmdistance table/blankh.,max. stroke up,adjustm. up: 2100 mmtable surface area: 4000 x 2200 mmdie-cushion pressure inside the table: 360 tstroke of drawing cushion in table: 300 mmdie-cushion pressure in pusher: 100 tstroke of drawing cushion in pusher: 150 mmram surface: 4000 x 2200 mmcolumn travel -side: 1300 mmdie-cushion inside the table: hydraulic, controlled die-cushion in pusher: hydraulic, controlled Cut Shock absorption: hydraulic total power requirement: kWweight of the machine ca.: 280 tdimensions of the machine ca.: mThe machine was overtaken 1999.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Press force: 250kN, Operating pressure: 280bar, Stroke: 300mm, Installation height: 500mm, Reach: 250mm, Oil filling: 280l, Ram speed: 105mm/s, Weight: approx. 2550kg. Documentation available. An on-site inspection is possible.

pressure: 800 tdistance between columns: 3160 mmstroke: 1100 mmcontrol: Siemens S5 distance table/blankh.,max. stroke up,adjustm. up: 1900 mmtable surface area: 3100 x 1900 mmdie-cushion pressure inside the table: 300 tstroke of drawing cushion in table: 400 mmdie-cushion pressure in pusher: 80 tstroke of drawing cushion in table: 150 mmram surface: 3100 x 1900 mmdie-cushion in pusher: hydraulic, controlled die-cushion inside the table: hydraulic, controlled total power requirement: 200 kWweight of the machine ca.: 150 tdimensions of the machine ca.: 4,95 x 3,3 x 10,2 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

An old eccentric press Elmerding with defective foot switch is available. Press capacity 30°: 25t, stroke adjustment range: 12mm-80mm, ram adjustment: 60mm, stroke rate: 120rpm, table adjustment: 150mm, safety distance: 144mm, weight: approx. 1450kg. Only 2-hand operation is possible. Documentation available. An on-site inspection is possible.

Press force: 250kN, ram stroke: 8mm-80mm, stroke rate: 180/min, installation height: 310mm, table dimensions X/Y: 550mm/400mm, ram dimensions X/Y: 355mm/220mm, machine dimensions X/Y/Z: approx. 1100mm/1400mm/2300mm, weight: approx. 2500kg. An on-site inspection is possible.

A single-column eccentric press Edelhoff including transfer unit is available. Press force: 130t, stroke adjustment: 30mm-130mm, ram adjustment: 75mm, stroke rate: 45/min, table dimensions X/Y: 1000mm/700mm, weight: approx. 5000kg. An on-site inspection is possible.

Press force: 650kN, Stroke: 150mm, Pressure piston diameter: 190mm, Column spacing X/Y: 950mm/460mm, Installation height: 500mm, Table dimensions X/Y: 900mm/870mm, max. stroke: 150mm, Operating pressure: 200bar, Machine dimensions X/Y/Z: approx. 1500mm/1750mm/2400mm, Weight: approx. 3000kg. Documentation available. An on site inspection is possible.

pressure: 800 tdistance between columns: 3160 mmstroke: 1100 mmcontrol: Siemens S5 distance table/blankh.,max. stroke up,adjustm. up: 1900 mmtable surface area: 3100 x 1900 mmdie-cushion pressure inside the table: 300 tstroke of drawing cushion in table: 400 mmdie-cushion pressure in pusher: 80 tstroke of drawing cushion in table: 150 mmram surface: 3100 x 1900 mmdie-cushion in pusher: hydraulic, controlled die-cushion inside the table: hydraulic, controlled total power requirement: 200 kWweight of the machine ca.: 150 tdimensions of the machine ca.: 4,95 x 3,3 x 10,2 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 160 tstroke: 810 mmthroat: 360 mmtable-size: 900 x 630 mmdimension of ram: 750 x 450 mmdayligth: 800 mmdiameter of pistons: 400/360 mmram stroke speed: 200 mm/sectotal power requirement: 17 kWweight of the machine ca.: 7 tThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 100 t

For sale is a used spotting press from the manufacturer Reis with an adjustable press force of up to 100 t. The 4-column press has a table size of 1600 × 1300 mm, a maximum open height of 950 mm and an ejector in the table, making it particularly suitable for spotting, tuning and tool work in mould and tool making. Here are the technical data of the offered machine: Technical data + information: Spotting press – REIS TUS 80-100 Allgemeine Disclosures - Name: spotting press - Manufacturer: REIS - Type: TUS 80-100 - Type: 4-column press - Year of construction: 1998 - Press force: 26–100 T (adjustable) - Retraction force max.: 45 T - Table size: 1600 x 1300 mm - Max. table load: 5,000 kg - Open height max.: 950 mm - Overall dimensions (WxDxH): approx. 3400 x 4200 x 3700 mm - Total weight: approx. 8,500 kg - T-slots: DIN 650 – 22 mm Hydraulik - Hydraulic pum ...

Key data: 100 t

For sale is a hydraulic single-column press (C-frame) from the manufacturer Durendus with an adjustable press force of up to 100 T. The machine has a table size of 800 × 600 mm, a maximum installation height of 700 mm and an adjustable stroke of up to 500 mm, making it suitable for a wide range of pressing, assembly and forming work in industry and production. The machine shown here has already been built and delivered on behalf of a customer. We can manufacture this machine for you at very short notice – gladly taking individual options into account. Here are the technical data of the offered machine: Technical data + information: Hydraulic Single Post Press – C-Frame – 100 T Allgemeine Disclosures - Title: Hydraulic Single Column Press - Type: C-frame / single-column press - Manufacturer: DURENDUS - Press force: 15–100 T (adjustable) - Max. installation heigh ...

ZTS KOSICE LE 160 C eccentric press was built in 1988 in Czechoslovakia by Závody Tažkého Strojárstva n.p. Košice. The machine is in very good technical condition and has been regularly maintained throughout its service life. All control solenoid valves were replaced in February 2023. ZTS KOSICE LE 160C is an excellent choice for a wide range of workpiece machining, i.e. punching, cutting and stamping. All of these machining processes are performed with a high press force of 160 tonnes, which, combined with a rigid design, enables the production of parts with high repeatability and excellent precision. The ZTS LE 160 C eccentric press weighs 10150 kg. Technical specifications of the ZTS KOSICE LE 160 C press - maximum press force: 160 t (1600 kN) - maximum number of slider strokes: 50/min - number of slider strokes in single mode: 30/min - maximum slider stroke: 120 mm -  ...

The machine is in good technical condition, after prior agreement it is possible to test it. - Nominal forming force: 120 t Working length: 3106 mm CNC control Delem (graphic 2D programming) Automatic calculation of bending sequence and collision detection Back gauge X axis with 2× manually adjustable stop fingers CNC electromotive height adjustment of the back gauge (R axis) CNC electrically controlled table deflection Upper tool adapter ROLLERI Equipment and accessories: - Front protective device (tilting door) - Rear protective device (sliding door) - 1× freely movable two-hand / foot control - Operating instructions including CE declaration

Hydropneumatic mode of operation Profile height: 200 mm under hold-down Max. Punch Height: 150 mm Wither height: 150 mm Weight: approx. 400 kg

Press brake Beyeler RT 80x3100 BJ 1992

Key data: 200 t

Capacity: 2000kN Year: 2017 Serial: 17X00095 Max Daylight: 1700mm Stroke: 1200mm Max Tooling Base Size: 2500x1500mm Max Advance Speed: 200 mm/s Electrical Supply: 415 Volts Phase: 3 Motor Rating: 50kW Continuous Approx. Net Weight: 25,000kg Max. Top Tool Weight: 10,000kg

Beutler P96-C630 - Eccentric Press - Mobile control panel - Infinitely variable drive - Clutch/brake combination - Overload protection in the ram - Light barrier - Gooseneck Lamp - Year of construction 1998 Technical data - Pressure: 630 kN - Stroke: 12 - 120 mm - Stroke rate: 30 - 130 rpm - Max. delay time: 96 ms - Projection: 300 mm - Distance table/plunger: 495 mm - Passage between body walls: 270 mm - Plunger area: 450 x 360 mm - Plunger adjustment: 120 mm - Table surface: 800 x 560 mm - Opening in the table: Ø 100 mm - Working height: 880 mm - Min. safety distance: 192 mm - Drive power: 5.5 kW - Operating voltage: 3x 400 V / 50 Hz - Machine dimensions WxHxD: 1800 x 2600 x 1600 mm - Dimensions control cabinet WxHxD: 800 x 1700 x 450 mm - Weight: approx. 5500 kg

pressure: 120/15 tdistance between columns: 860 mmstroke: 170 mmtable-size: 860 x 600 mmdayligth: 350 mmmax. distance table - ram: 520 mmram head dimension: 860 x 600 mmhole in the table: 200 x 140 mmtable height over floor: 850 mmtotal power requirement: 25 kWweight of the machine ca.: 7,5 tdimensions of the machine ca.: 2,3 x 1,7 x 3,4 mMaximum ram pressure: 120 kNMaximum pull-out pressure: 15 kNSick light curtainSafety distance: 180 mmMaximum overrun: 15 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 040 tchamfer lenght: 1600 mmdistance between columns: 1100 mmstroke of upper beam: 100 mmthroat: 195 mmworking feed: 10.0 mm/secreturn speed: 70.0 mm/sec: 180 barwork height max.: 840 mmtable width: 110 mmdayligth: 295 mmControl: ATL 550 total power requirement: 5.5 kWweight: 2500 kgrange L-W-H: 2100 x 1200 x 1800 mmEquipment:- NC-controlled hydraulic press brake, with torsion shaft- with ATLANTIC NC control - model ATL 550 Positioning of the backgauge (X axis) Positioning of the depth adjustment (Y1 Y2 axis) Possibility of programming different programs Memory capacity max. 200 programs - max. 400 blocks Swivel control panel, left front- Electro-motorized backgauge (X axis) with 2x stop fingers, manually adjustable (R Z axis)- Tool holder system A - with top wedge crowning- Split insert/bending tools- Lateral safety guards- rear safety guard- 1x freely movable double foot swit ...

pressure: 100 tdistance between columns: 400 mmstroke: 20 - 140 mmtable surface area: 900 x 710 mmram surface: 560 x 450 mmram adjustment: 80 mmdayligth: 470 mmno. of strokes: 70 Hub/mintotal power requirement: 10,5 kWweight of the machine ca.: 9 tdimensions of machine L x W x H: 1,98 x 1,60 x 3,10 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 50 t, 2550 mm

Hydraulic press brake Manufacturer Fasti Type UBGP 50/25 max pressing pressure 50t max working width 2550mm Lifting height 150mm with block matrix and div segments Press is in a used 100% functional condition. Can be loaded with overhead crane.

Hydraulic press manufactured in 2001. This AMADAs SCHIAVI HFB 220-40 features a robust 4000 x 220 Tons capacity and includes advanced safety features such as side and rear guards, and photocells that comply with regulations. With a use and maintenance manual provided, this refurbished machine is CE compliant. Consider the opportunity to buy this AMADAs SCHIAVI HFB 220-40 hydraulic press. Contact us for further details.

This Inanlar CNC HAP 70 25/21 was manufactured in 2018. It features a bending length of 2,550 mm and a bending force of 70 tons. The machine includes a finger protection system and supports for safety and efficiency. With a main motor power of 5.5 kW and a stroke of 185 mm, its ideal for precise bending operations. Contact us for more information about this machine.

pressure: 200 ttable length: 2200 mmtable width: 1550 mmdayligth: 2200 mmram return capacity: 6.000 kgtable load capacity: 10.000 kptotal power requirement: ? ca. 25-30 kWweight of the machine ca.: 30 tdimensions of the machine ca.: 4 7 7 mPacking: ca. 13,4 x 3 x 3 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 40.0 tchamfer lenght: 1600 mmdistance between columns: 1100 mmstroke of upper beam: 100 mmthroat: 195 mmworking feed: 10.0 mm/secreturn speed: 70.0 mm/sec: 180 barwork height max.: 840 mmtable width: 110 mmdayligth: 295 mmControl: ATL 550 total power requirement: 5.5 kWweight: 2500 kgrange L-W-H: 2100 x 1200 x 1800 mmEquipment:- NC-controlled hydraulic press brake, with torsion shaft- with ATLANTIC NC control - model ATL 550 Positioning of the backgauge (X axis) Positioning of the depth adjustment (Y1 Y2 axis) Possibility of programming different programs Memory capacity max. 200 programs - max. 400 blocks Swivel control panel, left front- Electro-motorized backgauge (X axis) with 2x stop fingers, manually adjustable (R Z axis)- Tool holder system A - with top wedge crowning- Split insert/bending tools- Lateral safety guards- rear safety guard- 1x freely movable double foot swi ...

Capacity: 1600 tons Slide stroke: 300 mm Slide stroke length at maximum force: 0,16 mm Distance adjustment between table and slider: 10 mm Slide stroke number in 1 min: 75 Length of a rod: 920 mm The closed height: 660 mm Table overall dimensions: 940x1200 mm Table height above floor level: 450 mm Slide overall dimensions: 860x910 mm The size of lateral windows: -Height: 560 mm -Width: 600 mm Main motor: 110 kW Press overall dimensions: -Length: 5060 mm -Width: 3940 mm -Height above floor level: 5125 mm Press weight: 120 tons

Press force: 100t, throat depth: 320mm, table dimensions X/Y: 850mm/610mm, ram dimensions X/Y: 600mm/355mm, stroke range: 10mm-130mm, ram adjustment: 80mm, stroke rate: 56rpm, installation height: 300mm, machine dimensions X/Y/Z: approx. 1900mm/1900mm/3150mm, weight: approx. 9000kg. On-site inspection is possible.

pressure: tchamfer lenght: mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: trequired space: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: tworkpiece diameter: mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 220 tchamfer lenght: 3200 mmdistance between columns: 2700 mmControl: Cybelec CybTouch 12 throat: 400 mmstroke: 220 mmdayligth: 480 mm: 140 mm/sbending speed: 0-10 mm/s: 110 mm/stotal power requirement: 18,5 kWdimensions: 3600 x 2000 x 2900 mmweight: 11.500 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.