presses used for sale (1,637)

Capacity 50 tons Stroke 750 mm Table size 1500x1000 mm

Offer 25374 Specifications: - Max. pressing force 100 t - Max. ram stroke approx. 500 mm - Lifting speed 25 mm/sec. - Return 125 mm/min - Installation height approx. 1000 mm - Projection to the middle of the ram 380 mm - Pusher clamping surface 530 x 400 mm - Plunger clamping pin 40 mm - Table size 750 x 560 mm - Table hole / through hole in the table 200 mm - Table height above floor 720 mm - Oil filling quantity approx. 200 ltr - Drive 400 V / 11 kW - Space requirement approx. W 1150 x H 3250 x D 1850 mm - Weight approx. 4600 kg

TAURUS shear baler Year 2006 1700 ton cutting force Working hours about 3,500 Side compression force 2x250 longitudinal compression force 150 tons. Machine in very good condition Always serviced and serviced regularly It is sold with its 805 kw Perin generator with a 3000 liter tank

Pressing force: 3150kN, table dimensions X/Y: 2500mm/1600mm, stroke (fixed): 280mm, stroke rate: 20-80strokes/min, weight: approx. 68000kg. Including Dreher transfer and feed line. The control system is defective. Documentation available. An on-site inspection is possible.

Inv. Num. : 948 Type: LVH 2500 Producer: ŽĎAS Created: 1961 Parameters: Depth: 1800 mm Width: 3450 mm Height above ground: 4650 mm Weight: 85 000 kg Voltage: 220 / 380 V Mains frequency: 50 Hz Workforce: 2500 t Number of strokes: 20/min Height of the lifts: 500 mm Minimum plunger distance from the table: 900 mm Maximum plunger distance from the table: 1400 mm Table surface: 1050 x 1400 mm Plunger area: 1050 x 1200mm

Inv. Num. : 946 Type: LKO 315 Producer: ŠMERAL Created: 1956 Parameters: Length: 3600 mm Width: 1750 mm Height: 4600 mm Plunger stroke: 180 mm Number of strokes: 60 / min Weight: 17 000 kg Power requirement: 25 kW Voltage: 380 V Frequency: 50 Hz

pressure: 12 tdistance between columns: / mmdayligth: / mmtotal power requirement: kWweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Nominal weight of the falling parts: 750 kg Max. number of blows per minute: 105 Kinetic energy: 1900 kg Distance from an axis of the slider up to bed: 750 mm Cylinder diameter: 600 mm Diameter of the plunger: 630 mm Max. headstock travel: 835 mm Dimensions: -Left-to-right: 3940 mm -Front-to-back: 1430 mm Height above floor level: 3260 mm Weight: -With an anvil-block: 25600 kg -Without an anvil-block: 16600 kg

Pressing force: 800kN, max. tool installation height: 380mm, max. upper tool weight: 300kg, stroke adjustment: 8mm-140mm, ram height adjustment: 100mm, stroke rate: 100/min, throat depth: 350mm, table dimensions X/Y: 850mm/670mm, ram area: 550mm/400mm. Machine dimensions X/Y/Z: approx. 2250mm/1550mm/2750mm, weight: approx. 9000kg. The machine was completely overhauled by the manufacturer in 2016 (retrofit). In 2024, the clutch, rotary union, press safety valve, and hydraulic oil cooler were replaced. In 2021, the drive motor and belt for the flywheel were converted to frequency-controlled speed. Documentation available. An on-site inspection is possible.

pressure: 100 tchamfer lenght: 3000 mmdistance between columns: 2550 mmstroke: 150 mmtotal power requirement: . kVANumber of working hours: . hworkpiece: workpiece: Number of strokes: total power requirement: kWweight of the machine ca.: 8,3 tdimensions of the machine ca.: mBack gauge 400mmThroat 250mmSpeed: 8mm /SkW: 6,5Volts: 380 The tech. Data are manufacturer or operator information and therefore non-binding. We reserve the right to prior sale, Our terms and conditions of saleapply exclusively.About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit.Your Markus Hirsch Tea ...

Technical data: Capacity, ton 1000 Ram stroke, mm 400 Max. ram strokes per min. 20 Shut height,mm 1000 Ram adjustment, mm 320 Table size, mm 3150 x 1800 Ram size (front-to-back), mm 1700 Column gap size, mm 1500 x 1900 Bolster plate thickness, mm 250 Ram travel to its extreme position where it develops nominal capacity, mm 12 Pneumatic cushion capacity, ton 200 Pneumatic cushion E51031468 stroke, mm 200 Upper knock-out capacity, ton 50 Main motor power, kW 132 Press dimensions, mm 5150 x 4700 x 7830 Press weight, kg 200000

pressure: 60 tstroke: 400 mmdaylight longitudinal/sideways: 820 x 300 mmdayligth: 900 mmliter capacity: 6,5 lfeed down: 6,1 mm/secfeed up: 10 mm/secMotor output: 2,2 kWweight of the machine ca.: 0,675 tdimensions of the machine ca.: 1,46 x 0,85 x 2,1 mPresses can be operated both by hand and by motor.Cylinders can be moved sideways.Safety valve with cylinder end position.CE markingThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 100 tstroke: 400 mmdaylight longitudinal/sideways: 1010 x 300 mmMotor output: 4,0 kWliter capacity: 11,0 ldayligth: 900 mmtable surface area: 1010 x 560 mmfeed down: 4,8 mm/secfeed up: 7,5 mm/secweight of the machine ca.: 0,9 tdimensions: 1550 x 900 x 2450 mmHigh-quality hydraulic press can be operated manually or by motor.Cylinders can be moved sideways.Safety valve at cylinder end position.CE markedThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

CONTROLS  PLC BECKHOFF SLIDE  total force (nominal): 880 to  stroke: 305 mm  cutting velocity min.: 5 mm/s  cutting velocity max.: 70 mm/s  closing velocity: 200 mm/s  returning velocity: 200 mm/sV-RING  nominal force: 400 to  stroke: 40 mmCOUNTER RAM  nominal force: 200 to  stroke: 40 mmTOOL DIMENSIONS  lower table (left-right): 1010 mm  lower table (front-back): 1600 mm  upper table (left-right): 1000 mm  upper table (front-back): 1000 mm  shut height max.: 460 mmLEVELLER UNIT  sheet width max.: 400 mm  sheet width (min): 100 mm  sheet thickness max.: 12 mm  sheet thickness min.: 1.6 mmSTRIP-FEEDER  feeder type: roll feeder   sheet width max.: 450 mm  sheet thickness max.: 16 mm  feeding step min.: 1 mm  feeding step max.: 999.9 mm  sheet length min: 3950 mm  speed max.: 48 m/min  Vertical adjustment: 140 mm  nominal force: 60 k ...

We would have all these machines as a package for sale. 1x Press brake 160to 3m 1x Press brake 60to 2m 1x KRC 150 robot 1x welding robot cell with Kuka robot and Fronius TPS4000 1x Micron

PAD 63 A high-speed press was built in 1978 in Poland by Fabryka Pras Automatycznych Warszawa-Włochy. The machine is used for precision machining of uncoiled sheet metal. All machining processes, i.e. stamping, punching, cutting and bending are performed fully automatically with a high press force of 63 tonnes. The PAD 63A high-speed press on offer has undergone an overhaul. The total weight of the machine is 6300 kg. Technical specifications of the PAD 63 A press - maximum press force: 63 t - slider stroke number: 100-320/min - slider adjustment: 60 mm - maximum distance from work table to slider surface: 320 mm - distance between columns: 480 x 400 mm - motor power: 15 kW - grease pump motor power: 0,4 kW - weight of the PAD 63 A machine: 6300 kg

Stroke: 135mm, max. sheet thickness: 20mm, max. bending length: 3050mm, pressing force: 80t, max. operating pressure: 2975psi, max. die opening: 250mm, bending angle range: 1°-42°, oil capacity: 150L, max. tool weight upper/lower: 40kg/115kg. Machine dimensions X/Y/Z: approx. 4000mm/2050mm/2450mm, weight: approx. 6000kg. Documentation available. An on-site inspection is possible.

CONTROLS  conventional PRESS DESIGN  drive system: eccentric / crank   frame design: C-frame, single sided PRESS FORCES  total force (nominal): 100 toSLIDE  slide force: 100 to  stroke rate (max.): 72 /minSLIDE (MECHAN. PRESS)  slide adjustment: 80 mm  stroke adjustment: yes   stroke min.: 8 mm  stroke max.: 112 mmTOOL ASSEMBLY DIMENSIONS  shut height (stroke down, adjustment up), BDC: 407 mmATTACHMENTS (PRESSES)  2-hand engagement: yes for safe tools only

Inv. Num. : 8718 Type: LDC 250 Producer: SMERAL Created: 1987 Parameters: Compressive force: 245 t Maximum stroke rate upper table: 38 1/min Adjusting the ram: 120 mm Ram stroke: 200 mm Machine weight: 29800 kg

Description: Hydraulic single-column press with cycle feed Type: HEP 100 Specifications Electrical connection: 400 volts/50 Hz +/- 3 % Drive power: 5.5 kW Total power requirement: approx. 6.5 kW Control voltage: 24 volts/50 Hz +/- 3 % Hydr. Max. connection: 210 bar Set: 200 bar Performance data Ram speeds AB: approx. 48 mm/sec. at max. 100 kN compressive force Working speed AB reduced adjustable to: approx. 10 mm/sec. at max. 100 kN compressive force Ram speed ON approx. 96 mm/sec. at max. approx. 50 kN retraction force Plunger stroke: max. 200 mm Flow rate of the pump: approx. 15 l/min.

Single Column Press Dunkes TYPE: HZS 160 Specifications: Manufacturer: Dunkes Model: HZS 160 Operating hours: approx. 2250 The machine is in good condition and fully functional.

pressure: 150 tchamfer lenght: 4050 mmdistance between columns: 3550 mmControl: CYBELEC ModEva Pac throat: 350 mmdistance between table / ram: 430 mmtable width: 250 mmstroke: 250 mmtotal power requirement: 18,5 kWweight of the machine ca.: 16500 kgdimensions of the machine ca.: 4400x2100x3200 mmEquipment/accessories:- Control conversion at the end of 2018- Electric backgauge 1250 mm- 10-stage die displacement- crowning- EHT 26 mm tool holder- Axes controlled: Y1,Y2,X,R- Sheet metal holding table- 4x manually adjustable stop fingers- pneum. Upper tool clamping- Safety light curtain- 3x height-adjustable support arms- Oil cooler- 2-hand foot switchThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 75 tstroke: 8-80 mmno. of strokes: 80-200 Hub/minram - range of adjustment: 70 mmtable surface area: 900x600 mmram surface: 900x470 mmhole in the table: 450x180 mmdist. between columns - front to rear: 500x350 mmdist. between pillars (front to rear): 788 mmtotal power requirement: 10 kWweight of the machine ca.: 10 tdimensions of the machine ca.: BxTxH 1600x1200x2800 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 150 tthroat: 310 mmstroke: 30-120 mmno. of strokes: 20-60 Hub/minram - range of adjustment: 90 mmtable surface area: 820x600 mmram surface: 550x430 mmhole in the table: 330x200 mmtable height: 750 mmtool hole in ram: Ø50 mmweight of the machine ca.: 9,5 tdimensions of the machine ca.: BxTxH 2500x2500x3000 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 35 tthroat: 240 mmstroke: 12-84 mmno. of strokes: 135 Hub/minram - range of adjustment: 70 mmtable surface area: 600x450 mmram surface: 360x180 mmhole in the table: 220x130 mmtable height: 630 mmtool hole in ram: Ø35 mmweight of the machine ca.: 2,5 tdimensions of the machine ca.: BxTxH 1500x2000x2600 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 100 tthroat: 375 mmstroke: 20-125 mmno. of strokes: 60 Hub/minram - range of adjustment: 80 mmtable surface area: 920x660 mmram surface: 700x450 mmhole in the table: Ø90 mmtool hole in ram: Ø50 mmweight of the machine ca.: 8 tdimensions of the machine ca.: 2100x1500x3300 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

CONTROLS  PLC SIEMENS S7 300 PRESS DESIGN  drive system: hydraulic PRESS FORCES  total force (nominal): 800 toPRESS TABLE  table surface (left-right): 2600 mm  table surface (front-back): 2000 mm  height above floor level: 540 mmSLIDE  stroke: 900 mmSLIDE (HYDR. PRESS)  approximation velocity max.: 460 mm/s  working velocity min.: 25 mm/s  working velocity max.: 44 mm/s  return velocity max.: 460 mm/sTOOL ASSEMBLY DIMENSIONS  shut height (stroke down, adjustment up), BDC: 1700 mmELECTRICAL SPECIFICATIONS  total power consumption: 180 kWDIMENSIONS / WEIGHTS  total weight approx.: 95000 kgATTACHMENTS (PRESSES)  press automation: yes   gripper transfer system: yes   acc. to actual accident protection regulation: yes   European CE standards: yes Complete hot forming line consisting of: Hydraulic press NEFF 800 to. Ruhstrat furnace system:- Natural gas heat ...

pressure: 63 tthroat: 260 mmstroke: 8-100 mmram - range of adjustment: 63 mmno. of strokes: 115 Hub/min: 316 mmtable surface area: 630x490 mmram surface: 315x260 mmhole in the table: Ø 140 mmtotal power requirement: 4 kWweight of the machine ca.: 7,5 tdimensions of the machine ca.: 2000x2000x2700 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

A Durmazlar press brake distributed by Knuth is available. Pressing force: 35t, bending length: 1350mm, motor power: 5.5kW, stroke: 100mm, stroke rate: 17/min, max. operating pressure: 240bar, oil capacity: 150l. Machine dimensions X/Y/Z: approx. 1400mm/1400mm/2100mm, weight: approx. 1750kg, operating hours: 1258h. An on-site inspection is possible.

- Pressure capacity: 22 t - Projection: 175 mm - Stroke: 120 1/min - Plunger adjustment: 50 mm - Table height adjustment 50 mm - Stroke adjustment: 8-80 mm - Table: 520 x 400 mm - Plunger: 250 x 160 mm - Turnbuckle with trunnion clamping, D35 mm - Motor power 1.5 kW - Very smooth running - Mechanical disengagement of the rotary wedge coupling via pneumatic pneumatic cylinder - Pneumatic foot switch - No UVV - 4 pieces of machine feet - Connection cable CEE plug 16 A - Air connection with quick coupling - Weight: approx. 2,000 kg - Dimensions: Width 820 x Depth 1100 x Height 1800 mm