Manufacturer:
(Category: 302)
Stock No.2452 1 used, partially overhauled and functionally tested pelletizing line Throughput up to 500 kg/h depending on the material, consisting of: Tamping unit Kreyenborg SW 100, drive 7.5 kW Extruder BKG single screw Ø 100 mm – 35 LD, Drive 132 kW – AC frequency controlled Screw speed up to 143 rpm.-1 screw depth 14 mm Heating capacity approx. 35 kW installed 1x athm. Degassing zone Screen-pack-changer Double piston Kreyenborg K-SWE 160 RS back-flush self-cleaning with screen surface 244 cm² BKG underwater pelletizer AH 300, complete with: Start-up valve incl. Hydraulic station Granulator with drive 4 kW Water pump 2.2 kW By-pass system, water tank with heating 9 kW installed and heat exchanger BKG granulate centrifuge TWE 300 with drive 3 kW pellet classifier table Control board and Siemens material feed conveying, big-bag filling station á ...
Stock No. 2680 1x partially overhauled and functionally tested Compounding extruder double screw, co-rotating intermeshing Segmented screws and cylinder barrel (water cooled) Screws 2x 64 mm - 40 L/D Screw speed up to 1200 rpm-1 Drive 482 kW-DC Gearbox Flender safety coupling atutomatik 3x degassing venting ports ( vacuum pump optional for extra charge ) 2x side feeding dosing extruder type ZSFE 50 twin screws with dm 48.5 mm with 4 kW each, speed up to 800 rpm.-1 Control cabinet with Siemens HMI Touch OPTIONAL at extra cost: 1) Screen-pack-changer changer 2) Vacuum pump 3) Pelletizing: ST strand, - WRG waterring or - UWP underwater pelletizing system 4) Granulate classifying sieve 5) gravimetric loss-in-weight blender / dosing system 6) Material conveying 7) Big-bag filling station 8) Start-up by our technicians Visit to our factory in Wuppertal. ...
Stock No.: 2107 1 used, partially overhauled and function-tested strand granulator with >> Granules Cutting Lengths Adjustment ( SV ) Manufacturer COMAC - Italy Type SG-100 SV Strand inlet width 100 mm cutting rotor width 110 mm, Parallel section rotor with 32 teeth Rotor Ø 200 mm >> strand pellet cutting length adjustment 2 drives: 1x for cutting rotor - 4 kW 1x for feed roller 1.5 kW with STOBER reduction gear Soundproof housing of the pelletizing chamber Visit / test run possible shortly by appointment. We also have matching strand cooling basins, strand blowers and classifying screens available from stock. Further strand granulators and other pelletizing systems/plants available from stock ( water ring - , hot impact and underwater pelletizing )
Stock No. 2590k 1 used compounding pelletizing line, throughput up to 1200 kg/h depending on material, consisting of: 1x Grav. Dosing system 5-component SITECOM incl. control 1x Extruder twin screw THEYSOHN type TSK 90 Screws 2x Ø 90 mm – 36 LD synchronization Segment screw and barrel, water / medium cooled Screw speed up to 300 rpm-1 Extruder drive 255 kW-DC 1x side dosing extruder TSD 75 twin screw with drive 3 kW 3x degassing openings 1x melt filter No. 1 type K –HS- Y with sieve 176 mm, incl hydraulic 1x melt pump with drive 22 kW 1x meelt filter No.2 type K-SWE 180 RS back-flush self-cleaning incl. hydraulic 1x strand head with 32 x Ø3.5 mm holes 1x strand cooling pool 620 x 5000 mm 1x string granulator SG 300, drive 11 kW Screen control ResoTec / control cabinet Visit / demonstration at short notice by arrangement. Further compounding lines and acce ...
Stock No. 2587 1 used pelletizing plant, functionally tested, Throughput up to approx. 600 kg/h depending on the material, consisting of: 1 volumetric dosage Extruder Plastmachines Type PME 100 Single screw Ø 100 mm – 35 L/D Drive 134 kW – DC 1x degassing zone Melt filter BKG type K-SWE 121 RS – backwasher incl. Hydraulics 3 kW Strand head with holes 20 x Ø 3.5 mm Continuous cooling pool 400 x 4000 mm with strand guide rollers Strand extraction Strand pelletizer SG 300 ResoTec control / control cabinet Viewing by arrangement - at short notice More pelletizing lines / extruders available from our Wuppertal plant & ready for demonstration
Blow head for LD-PE films with 80 nozzle insert and cooling ring available ... more information
Reifenhäuser screw with 120 mm diameter, 30 L/D for extruder model RT and / or RH 1651-1-120-30 ... more information
new and origin packed set of screw and barrel for Reifenhauser extruder, model RT5801-1-150-30, screw diameter 150 mm - 30 l/d ... more information
Tire houses screw 90 mm - 25 l/d many more screws available from stock, some as good as new ... more information
screw for PE and PP much more screws (some are new) available ... more information
Complete regranulation plant OMP Prealpina Type:ES-130. Screw and cylinder were renewed in November 2021 A new groove bushing as a spare part Simple degassing with vacuum pump DC drive used for PE/PP. Throughput at PE approx. 500-600kg. at PP.450-500.kg. per.h. Consisting of foil silo with agitator and discharge screw. Regrind/granulate dosing screw. Masterbatch dosing screw Tamping plant Extruder 130 L/D Hot tee granulator( also water ring granulator) Centrifuge Classifying sieve Removal with pressure blower. Plant is tested and stored (immediately ready for use)
Used Cincinnati conical twin-screw extruder model CMT 35. 2 pieces available: 1 pc. - new 1989 1 pc. - new 1990 Technical data: - drive: DC 9kW motor - heating zones: cylinder - 3, head - 3 - cylinder cooling - oil - vacuum degassing pump ... more information
Used twin-screw, parallel, counter-rotating extruder by Amut model BA92 NOMAX. New 2011. Output: 270 - 370 kg/h Hours of operation: 53638 h Other details: - Diameter of augers 92 mm - L/D ratio 28:1 - Drive power 60 kW (400V, 50 Hz, 3 ph) AC - Two sets of screws -for ABS processing -for PVC processing - Number of cylinder heating zones 7 - Number of cylinder cooling zones (air) 4 - Number of heating zones for head and adaptor 5 + 1 - Built-in pressure and temperature measurement system for plastic mass - Thermal oil unit for thermostating the worms for PVC - Drive power of vacuum degassing pump 11 kW - Drive power of screw feeder 1.5 kW - Without control (subassemblies available according to the list)
Output: approx. 255 - 450 kg/h (manufacturer's information from brochures; depending on material and profile; DEGUMA assumes no liability for actual, product-specific output) Straight head on hinged flange, fastening via screws; NEW SEVA motor, new control system ... more information
A brand-new extrusion recycling product UMAC (EREMA Group) series READYMAC Type 1109 TVE for processing polyethylene (PE), polypropylene (PP), polystyrene (PS), polycarbonate (PC), and polyamide 6 (PA6), with screen changer type SW RF, for processing printed films. Fully equipped. Capacity up to 450 kg/h, electrics 240/400 volts, 50 heart, immediately available. Auch + Technik e. Kfm. D-73728 Esslingen Phone +0049 1577 5329827
A brand-new extrusion recycling product UMAC (EREMA Group) series READYMAC Type 1109 TVE for processing polyethylene (PE), polypropylene (PP), polystyrene (PS), polycarbonate (PC), and polyamide 6 (PA6), with screen changer type SW RF, for processing printed films. Fully equipped. Capacity up to 450 kg/h, electrics 240/400 volts, 50 heart, immediately available. Auch + Technik e. Kfm. D-73728 Esslingen Phone +0049 1577 5329827
Automatic double wheel reel suitable for pipes from 10-32 mm OD Manufacturer: NEXTROM /Maillefer Type: MWB 1300G Year of construction: 1998 Condition: "as it is", ready for operation. ... more information
As good as new. ... more information