presses used for sale

Plate press, gluing press, veneer press, splicing press, heating press, molding press -Handover: in the current condition as seen -Heating plates: the middle heating plate is defective -Manufacturer: Paul Ott, veneer press heatable type JU 80 -Drive: hydraulic -Heating capacity: 24 kW -Working area: 2550 x 1350 mm - Opening height: 400 mm -Dimensions: 3325 /1540/H1850 mm

In 2007 Floor press from BÃ?TFERING, type 4 H 100,. Lower piston design Pressing area of 1250 x 2200 mm Aluminium plates electrically heated Total pressure of 100 to Operating pressure 320 bar spec. Pressure 3.5 kg/cm2 with full interpretation spec. Pressure at 80% design 4.5 kg / cm2 Hydraulic power 380 volts, 50 Hz, 1.5 kW Press plates: 2 piece ELKOM electric heating Panel solid hard aluminum in the thermally stable sandwich construction for temperature applications up to 200 ° C 2200 x 1250 x 18 mm + 19 mm Mono Lux + 19 mm V 100 insulation plate 17,500 Watts, 400 volts, 3 Ph. Surface smooth, flat, screw-free, gold anodized Plate construction hides more-row from the bottom screwed maximum continuous temperature 200 ° C incl. 2 piece cooling plate in Sandwitchbauweise. This is mounted below the insulation. The heatsink must be with a cold ...

Veneer press Fabr. Bütfering Slabs size 2.3 x 1.3 m Electric 4 cylinders diameter 120 mm Hydraulic with safety leash  ... more information

Press pressure up to 900 KN Hint: without ripcord  ... more information

Hydraulic glue press with heating base, infinitely variable temperature setting, stuffenlose setting of the adhesive holding time, Power: 5 kW, 380 v 50 Hz; Two-hand operation.  ... more information

pneumatic carcass press with 4 pressure elements from above 2 sides working area 3200 x 1600 - YOC 1975  ... more information

pressure: 100 tdistance between columns: 625 mmstroke: 150 mmtable surface area: 580x450 mmram surface: 580x340 mmhole in the table: Ø 150 mmtable height: 850 mmtool hole in ram: Ø 45 mmcolumn travel -side: 200x200 mmweight of the machine ca.: ca. 6,0 tdimensions of the machine ca.: BxTxH ca. 1300x1300x2750 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 250 tdistance between columns: 900 mmstroke: 300 mmtable surface area: 850x900 mmram surface: 800x880 mmstroke: 300 mmtable height: 1050 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... more information

Edge press of PanHans 923 with preheating ruler Working length 250 cm maximum 80 mm thick L x W x H: 300 x 60 x 100 cm Weight approx. 300 kg Built in 1976 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Veneer Press Gluing Press Plate Press Heat Press OTT Type: JU 65 YOC 1977 Press dimensions : 120 x 225 cm incl. heating plates The machine originates from the age-related abandonment of a small construction and cabinetmaking workshop and is available now. Dismantling and loading can be organized by us. Settlement by appointment. Buyers can also pick up and test the machine themselves on site. Condition see pictures, or please refer to the item description. Parts can also be picked up by yourself. All measurements are approximate. All information to the best of our knowledge but without warranty. Subject to prior sale. The items can be picked up by yourself or shipped at the expense of the buyer. Shipping costs are a guideline. Depending on the agreement of dismantling and loading, or removal, these may differ. Please inquire in advance for more detailed cond ...

pressure: 250 tdistance between columns: 850 mmstroke: 500 mmdayligth: 800 mmtable surface area: 800x800 mmram surface: 800x800 mmweight of the machine ca.: 12 tdimensions of the machine ca.: BxTxH 1600x1600x3400 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 25 tdistance between columns: 800 mmstroke: 100 mmdayligth: 450 mmtable surface area: 750x750 mmweight of the machine ca.: 3 tdimensions of the machine ca.: 1500x1500x2700 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... more information

pressing area: 2500mm x 1250mm; opening: 290mm; heating: elektric; plate surface: ALU - anodized; Emergency stop switch: yes, ripcord; pressure: 75t; number of cylinder: 4; electricity: ca. 33A; machine length: 3000 mm; machine width: 1500mm; weight: 3500kg;  ... more information

Pressing area: 2550mm x 1350mm; Aperture: 300mm; Heating: electric; Plate surface: ALU - eodized; Emergency shutdown: yes line; Pressing pressure: 90t; Number of cylinders: 4; Current consumption: approx. 33A; Machine length: 3000 mm; Machine width: 1500mm; Weight: 5000kg; ... more information

Glue press Etienne Format L x B: 3800 x 2700 mm Window frame press pneumatic Weight approx. 890 kg Year of construction 1980 The press is in good condition, ready to use. Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Description: Internal height min. 200 mm, max. 1350 mm Width min. 200 mm, max. 2500 mm Without CE certificate Voltage 400 V Pressure according to technical documentation up to 2000 kpApprox. Onsite Dimension. (l x w x h): 3,300 x 1,100 x 2,500 mm, weight approx.: 2,000 kg ... more information

Gebr. Frame press HESS Variant YOC 1983 pneumatic 0-15 bar Working area: approx. 2.40 m x 3.40 m 3 pressing units upright 2 pressing units on the side + 1 additional The machine is currently disassembled (see pictures 2 - 6). Picture 1 shows the machine before dismantling. Sold in ACTUAL condition and unrefurbished from carpentry dissolution. Fixed price.

Frame press Maweg Size: 400 x 240 cm hydraulic 3 vertical cylinders 2 horizontal cylinder Built in 1984 Weight approx. 2500 kg L x W x H: 480 x 110 x 270 cm The machine is in good condition, ready to use. Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

pressure: 40 tdistance between columns: 700 mmstroke: 150 mmtable surface area: 700x650 mmram surface: 670x650 mmhole in the table: Ø 120 mmtable height: 850 mmweight of the machine ca.: 4 tdimensions of the machine ca.: BxTxH 2000x18000x2700 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Electric hydraulic frame press model HAT 30 / 20, 3 upper, 2 side cylinders pressing range 3000 x 2000, Year of construction 86  ... more information