gluespreader machines used for sale

Description: - Edge banding machine - Serial number 37082 - Total installed power 32 KW - Edge thickness in strips up to 20 mm - Edge thickness in the roll from 0.30 mm to 3 mm - Workpiece thickness from 10 mm up to 60 mm - Adjustable feed speed from 10 m/min up to 24 m/min - Feed motor 5.50 KW - Motorized height adjustment - CNI control - Joint cutting unit, 2 x motor - Edge feeder for strips and roll, edge magazine for one edge roll - NORDSON MC 12 gluing unit for PUR adhesive - Pressure unit with (1+6) rollers - Snipping unit, 2 x motor - Rough trimming unit, 2 x motor (upper motor missing) - Fine trimming unit, 2 x motor 0.65 KW-12000 rpm - Profile trimming unit, 2 x motor - Profile scraper unit - Trimming unit swivels from 0° to 90°, motor 3 KW-3000 rpm - Flat scraping unit - Edge buffing unit, 2 x motor - Hot air blower unitApprox. Onsite Dimension. (l x w x h): 10,700 x 1,250 x  ...

I am selling an edge banding machine Holz-Her Sprint 1310, built in 2004. Configuration: Edge banding Cartridge glue Cross-cut saws Swivelling radius milling machines Radius pulling blade Polishing brushes Very good condition, fully operational.  ... more information

SECOND-HAND GLUE SPREADER OSAMA MOD. S2 R 1300 - CE RULES - working width 1300 mm - n. 2 rollers - Year 2004  ... more information

SPECIFICATIONS: Max. working length mm: 1300 2 rollers, diameter mm 200 top - bottom Complete with: - Glue container - Roller protection grille - Safety pedal  ... more information

Description: Joiningagreat 2 x 2kW /gluing cartridge system/capping/milling station radius chamfering 0-15°/radius drawing/ separating/ detergent spraying unit copy milling unit/ surface scraper/ fettling station edge thickness max.: approx. 0,4 - 8 mm [mm] workpiece height 6 - 50 [mm] feed speed approx.: 8 [m/min] / elect. connection: 400 V, 3Ph, 50 Hz PRICING IN FUNCTIONALLY TESTED CONDITION - SOLD WITHOUT WARRANTY! Data is taken from the manufacturer's brochure / documents and may differ from actual values. ATTENTION: it is expressly pointed out that this lot corresponds only to the scope of the lot description. If there are any objects on the photo that are not explicitly mentioned in the lot description, they are not part of the sale. Of course, this also applies to tools, additional equipment, accessories, software, operating equipment, etc. (in relation to the photo and lot d ...

Equipment: - Quick-change Quickmelt gluing part for hot melt adhesive. - Automatic edge magazine with roll plate and autom. Edge feeder - extended inlet ruler, adjustable - heavy pressure zone (with pgroamm adjustment) with a driven main pressure roller, as well as 3 repressure rollers - Motor-adjustable upper pressure. - Control panel on the machine inlet. - Electronic control PC 16 - Modem for remote service and remote maintenance - Noise protection cladding - autom. Chain track central lubrication - Interface for return (electronic) DAHR01/02/15 Aggregate assembly - Release agent specification workpiece - Joining milling unit 2 x 2.2 kW - Cross-cut unit 2 x 0.35 kW, pneum. Adjustment chamfer/straight - Milling unit 0-25 degrees, 2 x 0.55 kW counter-rotation, to flush milling machine, pneum adjustable pneum. 2-point adjustment Vertical probe rollers - Milling unit ...

Description: • Edgebander, edge banding machine • Edge thickness from 0.40 mm up to 25 mm • Worpiece thickness from 6 mm up to 60 mm • Minimum workpiece lenght 140 mm • Minimum workpiece width 60 mm • Adjustable feed speed from 8 m/min up to 20 m/min • Feed motor 4.40 KW • HOLZ-HER 1961 joint trimming unit, 2 x motor 2 KW-12000 rpm • Edge feeder for 1 edge coil, edge magazine for 1 edge coil • HOLZ-HER 1907 cartridge glue system with pot for granulated hot melt adhesive • HOLZ-HER 1926 K pressure group with (1+2) rollers • HOLZ-HER 1819 snipping unit, 2 x motor 0.45 KW-12000 rpm • HOLZ-HER 1962 rough trimming unit, 2 x motor 2 KW-12000 rpm • HOLZ-HER 1934 lower profile trimming unit, 2 x motor 0.45 KW-12000 • HOLZ-HER 1933 upper profile trimming unit, 2 x motor 0.45 KW-12000 • HOLZ-HER 1927 profile scraping unit • HOLZ-HER 1964 flat scraping unit • HOL ...

Description: Manufacturer: Grecon Dimter Finger Jointing line Machine type: Combipact 4 Serial number: 193.V000307, year 2005 Timber data: Type of timber: softwood or hardwood Length (min/max): 150/1000mm Width (min/max): 30/205mm Height (min/max): 16/80 mm Ratio length / max width: 2:1 Resulting length (min/max): 3.000/6.100 mm Dimensions: 21.000 x 8.000 x H2.000 mm Space required for operation and maintenance: 22.000 x 9.000 x H2.000 mm Supply of power: 400V, 50Hz, 91 kW, 160A Control voltage 24V DC Weight: 15.000 kg The line consists of: 1. Charging unit with compartment conveyor, type BF6/600/1500 2. Infeed station, type ESTA 600/1500 3. Shaping machine Combipact, type FDL-F-205/600/1000 4. Infeed station thread in station” for press, type EKK 240/4000 Re 5. Transfer station, typeUKB 600/1000 6. Front side press, type CONTI 6100 Ll Attention! The line may be dismantled after 1 ...

Manufacturer: Italpresse, Year: 2005, Type: Lock Form SS AIR , Work piece width min-max mm: 1330, Min.-max. workpiece length in mm: 2680, Min.-max. workpiece height in mm: 55, Heating system: elektrisch, Max. temperature °C: 150, Placing table: 2, Size of heating plate mm: 1450 x 2800, Pin system: no, Multifunktionsrahmen: yes, Automatical glue supply: yes, Year :2005

Manufacturer: Baberan Kaschieranlage, Type: ECO Line 1400 DSI, Year: 2006, Work piece width min-max mm: 250-1350, Min.-max. workpiece length in mm: 450, Min.-max. workpiece height in mm: 6-40, Working widht max mm: 1350, Feeding speed min-max m/min: 10-40, Brushing machine: yes, Urea plant: yes, Brushing machine: yes, IR zone: yes, Hardener machine: yes, Leimauftragsmaschine : 2, Double-sided: yes, Roller diameter mm: ca.300, Lamination calender: 2 Stück, Diameter of lamination calender in mm: ca.400, Roller diameter mm: ca.300, Rollers heated: yes, Year :2006

I am selling a fully equipped edge banding machine BRANDT ProfiLine KDF 790, built in 2006: Configuration: Input stop can be adjusted by menu Manually adjustable joint milling Edge banding with preheating tank Material pressure zone can be adjusted by servo motor Pneumatically adjustable cross-cut saws Heavy milling at the top + at the bottom manually adjustable Radius milling top + bottom servo motor adjustable Groove saw unit at the bottom Round unit 2-motor servo motor adjustable Radius scraper blade R2 pneumatically adjustable / second set R1 included Scraper blade surface Polishing brushes Separator injection at the front Clean injection at the rear Working height adjustable by servo motor Material height 6-60mm Edge material thickness 0.4-12mm Feed speed up to 20m/min. Overall length including feed plate 7860mm Mileage status 1,650,000 meters glued. Incl ...

I am selling a fully equipped edge banding machine BRANDT Optimat KDF 550 C, built in 2006: Configuration: Manually adjustable entrance stop Manually adjustable joint milling Edge banding EVA Material pressure zone can be adjusted by servo motor Pneumatically adjustable cross-cut saws Radius milling top + bottom manually adjustable Round unit 2 motor manually adjustable Radius scraper R2 pneumatically shut-off Scraper blade surface Polishing brushes Control panel Power Control PC20+ Working height adjustable by servo motor Material height 8 - 50mm Edge material thickness 0.4 - 8.0mm Feed speed 11m/min. Assembly length including feed plate 5860mm Total weight 2660kg Very good condition, fully functional!

Workpiece return for single-sided edge banding machines in left-hand design, machine length approx. 8-10m  ... more information

Edge thickness 0.4 - 3 mm Workpiece thickness: max 50 mm Min workpiece length 150 mm Feedspeed 22 m/min  ... more information

Description: - Inlet ruler with automatic adjustment and extension 500 mm - BONDING PART A20 BASIC - Pressure zone C with automatic adjustment - Release agent spray unit - Pre- and profile milling unit with pneumatic adjustment - Edge sanding unit KS10 - Profile sanding unit top/bottom PS41 / PS42 WITHOUT returnedge magazine with: 2 -fold roller, serial number: 0-200-21-6055, edge thickness: 0,3 - 3 (20) mm, workpiece thickness: 8 - 60 mm, workpiece overhang: 30 mm, feed: 18 - 25 m/min, joint trimming unit: 2 x 3 KW, gluing unit: A20/QA34/C, snipping unit: HL84 (2 x 0,8 KW), rough trimming unit: 2 x 1,5 KW, fine trimming unit: 2 x 0,4 KW, profile trimming unit: FF12 (4 x 0,4 KW), edge sanding unit: KS10 / PS41 / PS42, flat scraping unit: ja / yes, profile scraping unit: MN21 automatic, edge buffing unit: ja / yes, control: Power Control PC 22, return system: Nein / No, Approx. Onsite Dim ...

Barberan Lamination line include following machines: 1- GLUE UNIT ( MELER BRAND 250 LT) 2-FRONT LIFTER 3-FORK FOR FRONT LIFTER 4-GLUING MACHINE BARBERAN EN-PUR-4-1600 5-CONVEYOR BARBERAN IT-4000/16 6- LOADING FOR FOR CONVEYOR 7-PRESS BARBERAN CAL-H-2-1600 8- GUIDE ROLLER 9- BACK LIFTER  ... more information

ORMA disc gluing and screwing machine according to CE standards 4-roll gluing machine model I/413 with: - Working width 1300mm - Useful working height 100mm - double motorization, kw 0.75+0.75 - coating rollers D=250mm - dosing rollers D=180mm - with automatic brush washer Disc route with: - Useful working dimensions 3000x1300mm - Mechanical variable speed drive - with final photocells Year 2007, machines according to CE standards.

Description: Rubber pads conveyor belt renewed approx. 2022 Annual maintenance by HOMAG incl. various new parts (see photos) Second glue pot (serviced annually) Single-sided machine for joint trimming of straight workpiece edges, gluing and finishing of various edge materials from the roll or as strips, up to 20 m edge thickness, with longitudinal and transverse throughfeed. Fixed stop side on the left. BRIEF DESCRIPTION OF THE BASIC EQUIPMENT: BASIC MACHINE WORKPIECE TRANSFER DEVICE - TOP PRESSURE CONTROL power control PC22 FREE SPACE Joining unit GLUING PART A20 BASIC for rolls up to 3 mm and strips up to 20 mm NOISE PROTECTION CAPPAGGREGATE FREE SPACE for further processing units BASIC MACHINE: Continuous machine stand for setting up the processing units Workpiece support with extendable roller rail approx. 800 m Glue roller drive for feed stop Glue container lift with feed stop G ...

Manufacturer: Metapress, Year: 2008, Min.-max. workpiece length in mm: 300-1200, Min.-max. workpiece height in mm: 300-600, Hydraulical/pneumatical: Pneumatisch, High / low pressure: Niederdruck, Cylinder vertical: yes, Cylinder horizontally: yes, Inserted table: yes, Press power kg /cm²: 2, Wight approx. kg: 700, Year :2008

Equipment: - Quick-change gluing part for hot melt adhesive - Autom. Edge magazine with roll plate - Pressure zone with pneum. pressurized pressure roller and 2 free-running repressure rollers - Power Control PC 20+ control - Inlet ruler adjustable - Joining milling unit 2 x 2.2 kW - pneum. Adjustment caps, drawing blade, program adjustment side button rollers and pneum. 2-point adjustment vertical probe rollers - Cross-cut unit 2 x 0.18 kW - Milling unit 2 x 0.55 kW - Mould milling unit 1 x 0.35 kW - Drawing blade unit for PVC edges - Surface drawing blade glue joint - Cleaning agent specification workpiece - Schwabbelaggregat Specifications Edge thickness 0.4 - 8 mm Roller cutting max. 3 x 45 mm or 0.8 x 65 mm Workpiece thickness 8 - 60 mm Feed max. approx. 11 m/min. Electrics 400 V - 3 Ph. - 50 Hz Connection value approx. 10.5 kW Pneumatic connection 6 bar To ...