Manufacturer:
(Category: 307)
Extruding height: 1100 mm Cylinder: Nitriding hardened spray cylinder; Intake zone 4 D, water-cooled, with feed funneled filling opening Ø 50 mm, without feed roller; Zone 1: 16 D, oil-tempered, with temperature sensor; Zone 2: 10 D, oil-temperature-controlled, with temperature sensor Head: Straight head on screw flange; Head is electrically heated with heating sleeve 0.5 kW; Injection tool holder electrically heated 0.5 kW (no injection tool available) With temperature and pressure sensors (shut-off pressure on spray disc at 130 bar, 180°C) Temperature control: Without temperature control units – oil temperature control units can be provided on request and for an extra charge Gearbox: FLENDER helical gearbox; p=22 kW; i=13.865; immersion bath lubrication; Belt drive i=1.5 Motor: Siemens DC motor, 0.1-26 kW (limited to 21 kW), 10-2600 rpm (limited to 2037 rpm), 35-47 ...
Bipel Tiltmaster 120 Press Closing force 120ton Platen size 458 x 458 Opening force 180KN Ram stroke 100mm With vacuum Max. Daylight between platens 200mm Overall dims: 1195mm wide x 1000mm deep x 2000mm high Weight: 3000kgs ... more information
Winkworth 14Z HMX Hydraulic Extruder Mixer Model 14Z HMX Working capacity 22-25 litre Approx total volume of trough litres: 32 litre with Hasco Hydraulics Ltd power pack With Panel YOM Jan 89 ... more information
Winkworth 31Z HMX Hydraulic Extruder Mixer Model 31Z HMX Total volume 360 litre Working capacity 250 litre Internal dims: 740mm long x 790mm wide x 714mm deep Screw 220mm With oil jacketed trough Lagged and with 3x electric drives ... more information
Merkle Slitter Cutting width 1m Overall dims: 1.4m wide x 700mm deep x 1m high Weight: 500kgs ... more information
Matteuzzi RAS 90 Buffing Machine Computer controlled Buffing machine for retreading DIMS: 12ft long x 7ft wide x 8ft high Weight: 2500kgs ... more information
ROLL DIAMETER 550 mm POLL WORKING LENGTH 1530 mm MOTOR POWER 110 KW DIMENSIONS: 630022301830 (L×W×H) SPEED RATIO OF ROLLS 1:1.27 Structure description 1 Base frame is welded and annealed . 2 The motor is 3- phase asynchronous motor, protection levels :IP54. 3 The driving type :Single out- shaft or double out- shaft. The speed reducer is hard gear reducer,which has long service life and low noise. 4 The roller bearing is rolling bearing with Low noise, save power almost 20%. the roller bearing use grease lubricating. 5 The nip adjusting Motor type 6 This machine is equipped with two pieces of moving blade. 7 Safety device : Pull the safety rod to achieve emergency stop. It can be installed with kick stop device and emergency stop device for safety. 8 The electrical design theory conform to the TWO ROLL MILL specifications strictly . It is equipp ...
5501500 TWIN SCREW 1. 1 PC 5501500 OPEN MILL RUBBER MIXER 2. 1 PC 5501500 OPEN MILL RUBBER MIXER 3. ELECTRIC CONTROL CABINET WITH DRIVER 4. DIRECT CONNECTION (COUPLED) 5. BRONZE BEARINGS 6. AUTOMATIC LUBRICATION 7. 160 KW 990r/min ... more information
L/D=20.7 External dimensions 2700×1000×1400(LxWxH) Screw stiffness HRC65-68 Screw diameter 90mm Engine power 30KW/1470rpm SCREW LENGTH 1860 mm Heating section number/power 6kw×2 ... more information
ROLL DIAMETER 400mm POLL WORKING LENGTH 1000mm MOTOR POWER 45 KW DIMENSIONS: 447118501760 (L×W×H) SPEED RATIO OF ROLLS 1:1,27 Structure description 1 Base frame is welded and annealed . 2 The motor is 3- phase asynchronous motor, protection levels :IP54. 3 The driving type :Single out- shaft or double out- shaft. The speed reducer is hard gear reducer,which has long service life and low noise. 4 The roller bearing is rolling bearing with Low noise, save power almost 20%. the roller bearing use grease lubricating. 5 The nip adjusting Motor type 6 This machine is equipped with two pieces of moving blade. 7 Safety device : Pull the safety rod to achieve emergency stop. It can be installed with kick stop device and emergency stop device for safety. 8 The electrical design theory conform to the TWO ROLL MILL specifications strictly . It is equipped ...
Automatic hardness testing device with 4 heads Micro IRHD IRHD Type L IRHD Type N IRHD Type H The device needs gibitre software installed on the computer to work. The device consists of a stand and 4 heads ... more information
Automatic hardness testing device with 3 heads Shore 00 Shore A Shore D The device needs gibitre software installed on the computer to work. The device consists of a stand and 3 heads ... more information
A rotational shear viscometer according to Mooney for performing Viscosity tests (ML / MS 1+X), Stress Relaxation testing, Mooney Scorch, Delta Mooney testing on polymers as well as rubber compounds for quality control, research and development applications. ... more information
Machine number 185386/2008 ... more information
Machine number 205557/2012 Without softwear! Head failure! ... more information
with 15 cards + Rack S5 187U with 10 extension cards. Scope of supply shown on the picture. ... more information
Press 400x400 make ZDA, typ 10158 manualy operated electrical heated plates Clamping force 785 kN ... more information
Press 400x500 make ZDA Type 100660 manualy operated electrical heated plates Clamping force 1540 kN ... more information