Manufacturer:
(Category: 102)
swing diameter:400 mmcontrol:840 D SIEMENSturning speeds:3500 1/minz-axis:340 mmx-axis:1350 mmworkpiece height:400 mmTorque:820 turret head:12 Pos.rapid traverse:Z 30 / X 60 m/mintool holder:VDI 50 spindle head:A8 DIN 55026 spindle motor:60 kWweight of the machine ca.:14,8 tdimensions of the machine ca.:6 x 3,3 x 3,4 mlive tools,C-axis,workpiece storage left side,high pressure pump,chipconveyor,
Lathe with 4 tools only for 3-cylinder crank shaft ... more information
turning diameter over bed:850 mmturning diameter over slide rest:510 mmturning length:3000 mmtravel of cross-slide cross:600 mmmovement of the upper support:250 mmbed width:600 (Monoblock) mmspindle bore:100 mmspindle nose:DIN 55029 Größe11 spindle taper:Ø120mm/Konus 1:20 spindle speeds:5~630 1/minmetric threading:56,1~120 mmfeeds - longitudinal:0,08~9,6 mm/minfeeds - cross:0.04~4,8 mm/minrapid traverse longitudinal and cross:3640/1800 mm/mintailstock quill diameter:120 mmtailstock quill stroke:250 mmtaper in tailstock:6 MKmain drive motor:15 kWmax. workpiece weight between centers:4000 kgWeight approx.:6800 kgmachine width/height:1500x1500 mmmachine length:5150 mm4-jaw independent chuck:800 mmsteady fixed:Ø40~350 (mit Rolleneinsätzen) mmfixed steady:Ø100~520 (mit Rolleneinsätzen) mmfollower rest:Ø30~120 mmmultifix tool holder:Größe C Factory new heavy duty turning machine bran ...
turning diameter: mmturning length: mmcontrol: 840 weight of the machine ca.:14 tswing over bed:480 mmturning diameter over bed:330 mmturning diameter over bed slide:250 max. swing dia.:695 mm ... more information
turning diameter:380 mmturning length:750 mmcontrol:Manual Plus Heidenhain spindle bore diameter:45 mmpower main drive with:11 / 9 kWmain spindle speeds::3800 1/minmachine weight ab.:1900 kgdimensions of machine:2400 x 1600 x 1900 mmteach-in lathe incl. electronic handwheelsincl. collet system 173 Estatic steadymoving steadycooling systemaccessories toolholder system PARAT 25 x 25manualssteady movedsteady rest3-chaw-chuck SCHUNK Rota S plus D = 250 mm Under power in our showroommain spindle with new bearings ( 0 hours working ) approx. 28.600 h "machine on"
turning diameter:2000 mmfaceplate diameter:2000 mmmax. workpiece weight:6000 (fliegend) kgweight of the machine ca.:30 tmain drive motor:55 kW ... more information
turning diameter over bed:402 mmturning diameter over slide rest:245 mmturning length:750 mmcentre height:200 mmbed width:250 mmmax. workpiece weight between centres:280/300 kg:135 kgspindle bore:42 mmspindle turning speed range:40-2800 (3 Getriebestufen) U/minlongitudinal feed:0,044-0,662 mm/Ucross feed:0,020-0,296 mm/Umetrical thread cutting:0.5 - 7,5 mm/Uthreading WHITWORTH:60-4 TPIrange of module thread:0,25-3,75 mm:120-8 mm/min.diameter of quill:58 mmsleeve conus:4 MKquill stroke:180 mmfixed steady::Ø 10-125 (110-200 opt.) mmwith live steady:Ø 10-80 mmpower requirement:4 kWDRO:für 2 Achsen von FAGOR center morse:2 Stück3 jaw chuck Ø:200 mmBrand new Center Lathe KRAFT DLZ 200 SeriesMore information can be found in the appendix
turning diameter:1600 mmturning length:3000 mmcentre height:800 mmturning diameter over bed:1600 mmturning diameter over bed slide:1400 mmturning dia. over face-slide:1200 mmspeeds:5,6 -800 1/mintransmission ratio:3 spindle bore:112 mmturret (x-stations):8 / VDI 60 travel -x axis:850 mmtravel -z axis:3020 mmrapid power traverse in X-and Z direction:6 / 10 m/minpower maindrive:46 kWweight of the machine ca.:22 to.dimensions of the machine ca.:7,2 x 4 (3,11) x 2,7 mtech-in lathe, flatbed,tailstock,8-pos. BARUFFALDI turret with 4 live tools, power 9kW,4-pos. BARUFFALDI square-headed turret horizontal,C-axis,3-jaw hydr. chuck SMW Autoblock KNCS 800/165, dia. 800mm,quick adjustment, power cylinder with 2 pressure clamping system,chipconveyor,coolant device,accessories
turning diameter:450 mmturning length:1000 mmcontrol:FAGOR 8055 max. swing over slide:260 mmbed width:300 mmspindle taper:A2-6 spindle speeds:0-3000 1/min.spindle bore:65 mmtransmission ratio:1 tailstock quill diameter:68 mmtailstock quill stroke:200 mmtaper of tailstock quill:4 MKmax. length of work piece:1000 mmrapid traverse x/z:12/15 m/minpower requirement:9 kWweight of the machine ca.:1400 kgdimensions of the machine ca.:2800x1215x1750 mmautomatic tool changer:8-fach CNC controller:FAGOR 8055 tools:1 Satz :aus Guss New CNC lathe KRAFT ST 225/1000 with FANUC 0i mate TDMade in EuropeFor more information please see the attached documents
max. workpiece diameter:110 mmmin. workpiece diameter:3 mmworkpiece length:30 -400 mmtotal power requirement:11 kW ... more information
-Flood damage machine, -mechanically still used a year later, -Main motor defective, geometrically fine, -little used, electrics in order, -Stanko Carousel DM (Wolf, Solventum) Attention! This machine has already been dismantled and is in storage. ... more information
max. workpiece diameter:29 mmmin. workpiece diameter:26 mmworkpiece length:66 mmthe system was originally delivered for the following workpiece sizes: diameter 26mm - 29mm length 65mm - 66mmChanging parts in the clamping device, handling, etc. would probably result in diameters of up to approx. Ø50mmTotal length will probably be almost 400 mm possible with a few conversions.Also dependent on tool lengths, machining lengths on the component, etc.
faceplate diameter:3000 mmswing diameter:3400 mmturning height:3000 mmmax. turning diameter:3400 mmmax. workpiece weight:25 tweight of the machine ca.:105 tDimensions (L/W/H):6450x7500x6950 mm ... more information
turning diameter over bed:402 mmturning diameter over slide rest:245 mmturning length:1000 mmcentre height:200 mmbed width:250 mmmax. workpiece weight between centres:280/300 kg:135 kgspindle bore:42 mmspindle turning speed range:40-2800 (3 Getriebestufen) U/minlongitudinal feed:0,044-0,662 mm/Ucross feed:0,020-0,296 mm/Umetrical thread cutting:0.5 - 7,5 mmthreading WHITWORTH:60-4 TPIrange of module thread:0,25-3,75 mm:120-8 mm/min.diameter of quill:58 mmsleeve conus:4 MKquill stroke:180 mmfixed steady::10-125 mmwith live steady:10-80 mmpower requirement:4 kWcenter morse:2 Stück3 jaw chuck Ø:diverse Größen als Option Brand new Center Lathe KRAFT DLZ 200 SeriesMore information can be found in the appendix
number of spindles:6 spindle passage:18 mmturning length:63/50 mmweight of the machine ca.:4,5 tspindle drive motor:11 kW ... more information
turning diameter over bed:502 mmturning diameter over slide rest:310 mmturning length:1500/1000 mmcentre height:250 mmbed width:300 mmmax. workpiece weight between centres:750 kg:225 kgspindle bore:58 mmspindle turning speed range:85-1250 (3 Getriebestufen) U/minspindle nose:A2-6 longitudinal feed:0,05-0,752 mm/Ucross feed:0,022-0,296 mm/Umetrical thread cutting:0.5 - 7,5 mm/Uthreading WHITWORTH:60-4 TPIrange of module thread:0,25-3,75 mm:120-8 mm/min.diameter of quill:69 mmsleeve conus:4 MKquill stroke:200 mmpower requirement:5,5 kWMachine size (LxWxH):(Spw. 1500mm) 3130x960x1550 mmmachine weight:2090 kgcenter morse:2 StückBrand new Center Lathe KRAFT DLZ 250 SeriesMore information can be found in the appendix
turning diameter:230 mmturning length:810 mmcentre distance:1.000 mmturning diameter over bed:460 mmspindle passage:56 mmchucking diameter:200 mmturret head:8 x VDI 30 Pos.turning speeds:3.100 1/minmax. workpiece weight:570 kgspindle motor:18 kWdimensions of the machine ca.:3,7 x 1,9 x 1,8 mweight of the machine ca.:2,9 tteach-in lathe,PARAT tooling-system,hand operated collet chuck,3 jaw chuck,4 toolholders
turning diameter:1010 mmturning length:3000 mmcontrol:FANUC Oi TF mit Manual guide max. swing over slide:718 mmbed width:500 mmspindle taper:A2-11 spindle speeds:0-1400 1/min.spindle bore:130 mmtransmission ratio:2 Stk.tailstock quill diameter:120 mmtailstock quill stroke:300 mmtaper of tailstock quill:6 MKmax. length of work piece:3000 mmrapid traverse x/z:7,5/10 m/minpower requirement:22 kWweight of the machine ca.:8050 kgdimensions of the machine ca.:5800x2290x2515 mmturret:Duplomatic DM TR25 with BMT75 (m. Y-Achse) c-axis:kontin. mit separatem Motor 3-jaw hydraulic chuck:500 tools:1 Satz New CNC lathe KRAFT ST 500/3000 with Fanuc Oi TDMade in EuropeFor more information please see the attached documents
equipped with spare chuck, protective caps, lathe goggles, ... more information
-face plate diameter 2,000 mm, -Turning diameter 2,500 mm, -Total height of crossbeam lower edge to face plate 1,570 mm, -vertical ram travel 1,100 mm, -max. workpiece weight 9 t, Attention! This machine has already been dismantled and is in storage. ... more information