injection moulding machines used for sale

ELWIK RT-C1 hot runner control system is a very important device for ensuring the right temperature during the injection process. The temperature controller for an injection moulding machine, having one heating zone with current load of 16 A, is used in cooperation with central nozzles, which enables the processing of all types of plastics. The temperature can be regulated from 0°C to 500°C. Thanks to the functions and protections used, the temperature cmould temperature controller guarantees continuous and uninterrupted operation, preventing, for example, complete burning out of the heater by drying it when the supply voltage is reduced. The extremely important auto-adaptation function automatically sets the P, PI, PID parameters without exceeding the set temperature, while the sequential control, especially important with a large number of nozzles installed in the mould, significa ...

The BATTENFELD BA 600 CDC injection molding machine was built in Austria in 2002. It is equipped with Unilog B4 control. It has a closing force of 600 kN forms. The screw diameter is 33 mm and the injection volume is 99 cm3. The machine has plates for mounting injection molds with dimensions of 511 x 511 mm, and the clearance between the columns is 320 x 320 mm. The injection molding machine is equipped with a receiving robot, hot runners, a conveyor belt for collecting moldings, four pillows, a string of cores and technical documentation. Technical parameters of the BATTENFELD BA 600 CDC injection molding machine – control: Unilog B4 – dimensions of tool plates: 511 x 511 mm – clearance between columns: 320 x 320 mm – tool height, min. : 150 mm – opening path: 511 mm – injection pressure: 2022 bar – injection volume: 99 cm3 – injection weight: 90 g – screw  ...

The injection blow molding machine VICTOR MACHINERY MSZ 30 for the production of bottles was built in 2015. Technical parameters : - screw diameter: 40 mm - screw L / D: 22: 1 - injection weight (HDPE): 190 g - maximum speed of the screw: 10-225 rpm. - heating power: 8.3 kW - injection clamping force: 292 kN - blow clamping force: 46.7 kN - maximum plate size (L x W): 400 × 270 mm - minimum mold thickness (H): 180 mm - mold heating capacity: 3 kW - opening: 220 mm - drying cycle: 3.5 sec. - engine power: 15 kW - hydraulic pressure: 15 MPa - suitable bottle range: 3-800 ml - maximum bottle height: ≤190 mm - maximum bottle diameter: ≤100 mm - minimum air pressure: 1MPa - compressed air discharge rate: ≥0.7 M3 / mm - water flow: 3 M3 / h - total rated power with mold heating: 26.3 kW - dimensions (L x W x H): 3.26 x 1.2 x 2.2 m - net weight: 4 tons

B&A REF: 9027 TON: 110TON SHOT WEIGHT: 210 SCREW DIAMETER: 40MM STROKE VOLUME: 235CM3 INJECTION PRESSURE: 1700AR PLATEN SIZES: 680 x 650MM DBTB: 450 X 400MM MIN MOULD HEIGHT: 150MM MAX MOULD HEIGHT: 500MM MOULD OPENING STROKE: 410MM MAX DAYLIGHT: 910MM EJECTOR STROKE: 150MM CONTROLS: DIMI EL 2000 AIR VALVES: 1 MOTOR: 15 HEATING CAPACITY: 9.3KW SCREW DRIVE: HYDRAULIC

Displacement: 1500 cm³ Clamping force: 2500 kN Injection pressure: 2000 bar Table height: 1,000 mm Locking system: fully hydraulic Voltage: 380 V Motor power: 26 kW Cooling water: 1 m³/h Weight: 5.5 t - Injects from above (type ZO) - Ergonomic overall design of the vertical machine - Generously dimensioned clamping unit - Extensive automation options for vertical machines - "One Piece Design" for maximum flexibility The machine belongs to a German company and until recently was in operation at their Serbian plant and ran flawlessly.

Table height: 1000 mm Locking system: fully hydraulic Clamping force: 2500 kN Spray volume: 1500 cm³ Hydraulic oil: 40/46 cPcs. Compressed air: 6 bar Voltage: 400 V Weight: 6.35 t - Injects from below (type VU) - Ergonomic overall design - Generously dimensioned clamping unit - Fully hydraulic extensive automation possibilities of vertical machines - "One Piece Design" for maximum flexibility The machine belongs to a German company and until recently was in operation at their Serbian plant and ran flawlessly.

Article number: 27-06-304 Manufacturer: Arburg Very good general condition Machine workshop-tested Shipping time: All rights reserved. Year of construction: ca.1985 L x W x H: approx. 2700x1200x1800mm Weight: approx. 930kg Closing side: Clamping force: approx. 250kN Holm dimension hxv: ca.221x0mm Plate size hxv: approx. 342x250mm Installation height min: ca.150mm Installation height max: approx. 300mm Plate spacing max: approx. 500mm Aperture travel: approx. 200mm Spray side: Screw diameter: approx. 22mm Displacement: approx. 38cc Injection pressure: approx. 1500bar Other accessories on request Price and other technical data on request

Engel ES 1350/300 HL Year of construction 2001 + 2003 Hours: 77623 h + 92737 h Clamping force: 300 tons. Screw diameter: 70 mm 4 core pulls incl. Wittmann removal robot  ... more information

Arburg 270U-250-70 (221) Description General information SKU: (221) Availability: In stock Year of construction: 2005 Brand: Arburg Specifications Injection weight: 20 g Clamping force: 250 kN Stand: Used Screw diameter: 18 mm Injection pressure: 2500 bar Tie bar spacing: 270 x 270 mm Clamping plate size: 380 x 380 mm Tool installation height min.: 200 mm Control: Selogica Language: German Power: 35 kW Operating hours: 82,985 h Curmtbe2w8 Weight: 2100 kg Dimensions: 3m x 1.1 m Funnel: No Core Train: Yes Euromap: Yes

ARBURG 200 TON WITH ROBOT WORKING HOURS ARE PRESENT ON THE PHOTOS YEAR : 1999 TECHNICAL DATA: EUROMAP SIZE: 2000-675 CLAMPING FORCE: 2000KN SCREW 50mm closing force: 90 kn OPENING STROKE MAX 650mm I EXCELENT WORKING CONDITION, MACHINE IS WORKING DAILY PRODUCTION MACHINE IS AWAILIBLE IMEDIATELY WE ORGANIZE DISMANTLING LOADING AND TRANSPORT TO THE CUSTOMER

ARBURG 270 S 150-60 U ALLROUNDER MACHINE WAS FULLY SERVICED NOT LONG AGO WITH NEW SCREW TECNICAL DATA IN LIST -PHOTO EUROMAP 150-60  ... more information

We have in our workshop and awaiting refurbishment this BOY 22D. The machine is a compact 22 tonne clamp machine with a very easy to use controller with the Dipronic system. These machines have stood the test of time and remain very popular as they are simple to use, cheap to repair and reliable. Machines awaiting refurbishment can be reserved with a small deposit and the refurbishment is then prioritised and scheduled. Refurbished machines from STV Machinery undergo a comprehensive test procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. Machines are ultra clean and cosmetically as good as we can get them. We guarantee our refurbs are delivered fault free and leak free. Category: Injection Moulding ID: 12646 Manufacturer: ...

Awaiting refurbishment at our works in Wellingborough, Northamptonshire is this high precision BOY 12A injection moulding machine. Fitted with the Procan controller. The 12A from BOY is one of the most common small moulding machines we see, it is extremely accurate while still maintaining versatility with tooling and familiar control setup. Refurbished machines from STV Machinery undergo a comprehensive test procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. Machines are ultra clean and cosmetically as good as we can get them. We guarantee our refurbs are delivered fault free and leak free. Category: Injection Moulding ID: 12882 Manufacturer: BOY Model: 12A Datasheet (PDF): View Here Viewing: Not yet refurbished Condit ...

Awaiting refurbishment at our works in Wellingborough is this BOY 30M machine with Procan controller. These 30 tonne clamp machines from BOY are some of the smallest (footprint wise) available on the market. The 30M’s are a rarer variant of the market leading BOY 22. The key difference, aside from the uprated clamp force, is that the 30M’s have larger platens and a four tiebar design, allowing for greater versatility. Machines awaiting refurbishment can be reserved with a small deposit and the refurbishment is then prioritised and scheduled. Refurbished machines from STV Machinery undergo a comprehensive test procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. Machines are ultra clean and cosmetically as good as we can get ...

Now fully refurbished is this Arburg 420C 1000-350 injection moulding machine. This machine was manufactured in 2005 and is fitted with the ever-popular Selogica controller. It’s fitted with a 40mm diameter screw which gives a maximum shot weight (PS) 153g and single air blast. This machine comes with it’s own anti-vibration mounts and the original operators manual. Refurbished machines from STV Machinery undergo a comprehensive refurbishment procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. Machines are ultra clean and cosmetically as good as we can get them. We guarantee our refurbs are delivered fault free and leak free. Prices shown are ex-works, but we can quickly provide DAP (Delivered at Place) Incoterm pricing on r ...

Now fully refurbished by the team at STV Machinery is this BOY 22M VH injection moulding machine. This machine was manufactured in 2002 with very low 12,187 run hours. It is fitted with a 24mm screw. Refurbished machines from STV Machinery undergo a comprehensive test procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. Machines are ultra clean and cosmetically as good as we can get them. We guarantee our refurbs are delivered fault free and leak free. Category: Injection Moulding Latest Refurb ID: 12066 Manufacturer: BOY Model: 22MVH Datasheet (PDF): View Here Viewing: Available to inspect by appointment Condition: Refurbished with guarantee Year: 2002 Clamp Force (t): 22 Screw Diameter (mm): 24 Max Shot Weight (PS)  ...

Production year: 2004 Injection unit: .../500 Screw diameter: 40 mm Specific injection pressure: 2019 bar Injection volume: 251 ccm Injection weight: 239 g Tool closure system: 120/... Clamping force: 120 t Tool plate dimensions: 740 x 680 mm Distance between columns: no columns mm Tool height: 300 mm Opening distance: 500 mm Max.Distance plates: 800 mm Ejector stroke: 130 mm General data: Pickup date: Immediately Dimensions (m) LxWxH: 5,1 x 1,5 x 2,1 m Weight: 7600 kg Instrumentation: - 2 x pneumatic valve - hot runner connection - bimetallic injection system - we have to the Picker machine

Clamping force: 130 t Year of construction: 1999 Injection weight in hp: 194 (hp) g Control type: Selogica Injection unit: .../350 Screw diameter: 45 mm Spec. Injection pressure: 1670 bar Spraying volume: 230 ccm Injection weight in hp: 194 (hp) g Hydr. Drive power: 22 kW L/D Screw Ratio: 18 Clamping unit: 1300/... Clamping force:: 130 t Size of clamping plates: 615 x 615 mm Lights spar spacing: 420 x 420 mm Ejector force: 40 kN Tool installation height: 250 mm Aperture travel: 500 mm Max. plate spacing: 750 mm Ejector travel: 175 mm General information: Fuel tank capacity OIL: 240 l Weight: 4100 kg Dimensions(m) LxWxH: 4.4 x 1.4 x 2.1 m

Clamping force: 35 t Year of construction: 2006 Injection weight in PS: 30 g Control Type: NC4 Injection unit: .../80 Screw diameter: 22 mm Spec. Injection pressure: 2061 bar Spray volume: 34.2 cc Injection weight in PS: 30 g Hydr. Drive power: 7.5 kW Cylinder heating capacity: 5.1 kW Clamping unit: 350/... Clamping force:: 35 t Size of clamping plates: 460 x 450 mm Lights spar spacing: 280 x 280 mm Aperture travel: 350 mm Max. plate spacing: 530 mm Ejector travel: 100 mm General information: Delivery Time: Natychmiast Weight: 2750 kg Dimensions(m) LxWxH: 3.2 x 1.2 x 2.0 m Equipment Filling funnel Sorting flap bimetallic plasticizing structure hydraulic core on movable plate

Clamping force: 60 t Year of construction: 2000 Injection weight in PS: 18 g Control type: Selogica Injection unit: .../150 Screw diameter: 15 mm Spec. Injection pressure: 2500 bar Spraying volume: 20 ccm Injection weight in PS: 18 g Clamping unit: 600/... Clamping force:: 60 t Size of clamping plates: 570 x 570 mm Lights spar spacing: 370 x 370 mm Tool installation height: 200 mm Aperture travel: 450 mm Max. plate spacing: 650 mm Ejector travel: 150 mm General information: Fuel tank capacity OIL: 150 l Weight: 3600 kg Dimensions(m) LxWxH: 4.0 x 1.2 x 2.1 m