injection moulding machines used for sale

Manufacturer: Krauss Maffei Type: KM 650-3500-700 CZ Year of construction: 2007 Control: MC 4 Clamping unit: Clamping force: 650 t Opening distance: 1150 mm Tool installation height min.: 600 mm plate spacing : 1750 mm Tie bar distance (h x v): 1100 x 900 mm Panel dimensions (h x v): 1510 x 1370 mm Centering (nozzle ejector plate): 200 / 200 mm 1.Injection unit: Screw diameter : 80 mm Injection weight in hp. Max. : 1400 g Displacement: 1543 cc Injection pressure: 2205 bar 2. Injection unit: Screw diameter: 45 mm Injection weight in polystyrene: 278 g Displacement: 305 cm³ Injection pressure: 2,336 bar Accessories: 2 x Air valve 16-fold cascade 3 x core pull on BWAP 3 x core pull on FWAP 20 x hot runner control units Robot interface: Euromap 67 Metrics: Total weight: 34,500 kg Total size L x W x H: 7.8 x 2.5 x 2.5 m Operating hours: 45400 h  ...

Manufacturer: BATTENFELD Type: HM 1300-9200H-7700H-BM Control: UNILOG B4 Clamping force: 13000 kN Year of construction: 2005 Technical data closing page: Drive type: fully hydraulic Closing type: Full hydraulics Type: four-spar Clamping force: 13000 kN Tie bar size h: 1600 mm Tie bar size v: 1250 mm Panel size h: 2220 mm Panel size v: 1880 mm Installation height min: 1000 mm Installation height max: 1800 mm plate spacing max.: 3850 mm Opening distance: 2850 mm Ejector stroke: 350 mm Ejector force: 165 kN Centering movable plate D: 315 mm Centering fixed plate D: 315 mm Technical data spray side: Screw diameter: 120 mm Displacement: 5655 cc Spray pressure: 1630 bar Screw length: 22 l/d Plasticizing current: 144 g/s PS The technical data of the 2nd injection unit are as follows: Injection unit II 7700 Screw diameter 100 mm, Specific spray pressure 1960 ...

Rexroth double pump for Battenfeld injection moulding machine R900737658 SYDFE1-20/100R R900737659 SYDFE1-20/071R  ... more information

Inverter for ENGEL robots Acopos Multi PO 220 Acopos Multi CO160  ... more information

overhauled Rexroth double pump for Krauss Maffei SGM machines  ... more information

Rexroth double pump for Battenfeld injection moulding machine SY2DFE1-2X/100-100 MNR: R901016480  ... more information

Complete control CC 90 for ENGEL injection moulding machines  ... more information

various control cards CC 90 for ENGEL injection moulding machines  ... more information

B&A REF: 9002 TON: 250 SHOT WEIGHT: 340 SCREW DIAMETER: 45MM STROKE VOLUME: 374CM3 INJECTION PRESSURE: 2250AR PLATEN SIZES: 860 X 790MM DBTB: 590 X 530MM MIN MOULD HEIGHT: 200MM MAX MOULD HEIGHT: 650MM MOULD OPENING STROKE: 550MM MAX DAYLIGHT: 1200MM EJECTOR STROKE: 225MM CONTROLS: COLUMBIA CORE PULLING: 1 AIR VALVES: 1 MOTOR: 22 HEATING CAPACITY: 12KW ROBOT INTERFACE: EUROMAP 67 SCREW DRIVE: HYDRAULIC

B&A REF: 9017 TON: 180 SHOT WEIGHT: 360 SCREW DIAMETER: 50MM STROKE VOLUME: 392CM3 INJECTION PRESSURE: 2000AR PLATEN SIZES: 760 X 760MM DBTB: 520 X 520MM MIN MOULD HEIGHT: 250MM MAX MOULD HEIGHT: 600MM MOULD OPENING STROKE: 460MM MAX DAYLIGHT: 1060MM EJECTOR STROKE: 150MM CONTROLS: CC 200 AIR VALVES: 1 HEATING CAPACITY: 15.3KW ROBOT INTERFACE: EUROMAP 67

B&A REF: 9001 TON: 160 SHOT WEIGHT: 260 SCREW DIAMETER: 40MM STROKE VOLUME: 285CM3 INJECTION PRESSURE: 2100AR PLATEN SIZES: 780 X 740MM DBTB: 510 X 450MM MIN MOULD HEIGHT: 170MM MAX MOULD HEIGHT: 550MM MOULD OPENING STROKE: 460MM MAX DAYLIGHT: 1010MM EJECTOR STROKE: 200MM CONTROLS: DIMI EL2 PLUS CORE PULLING: 1 AIR VALVES: 1 MOTOR: 19 HEATING CAPACITY: 12KW SCREW DRIVE: HYDRAULIC

B&A REF: 8827 TON: 120 SHOT WEIGHT: 211 SCREW DIAMETER: 40MM STROKE VOLUME: 232CM3 INJECTION PRESSURE: 1710AR PLATEN SIZES: 770 X 730MM DBTB: 480 X 440MM MIN MOULD HEIGHT: 300MM MOULD OPENING STROKE: 500MM MAX DAYLIGHT: 800MM EJECTOR STROKE: 125MM CONTROLS: ORION CORE PULLING: 1 AIR VALVES: 1 MOTOR: 15 HEATING CAPACITY: 9.3KW SCREW DRIVE: HYDRAULIC

B&A REF: 9027 TON: 110TON SHOT WEIGHT: 210 SCREW DIAMETER: 40MM STROKE VOLUME: 235CM3 INJECTION PRESSURE: 1700AR PLATEN SIZES: 680 x 650MM DBTB: 450 X 400MM MIN MOULD HEIGHT: 150MM MAX MOULD HEIGHT: 500MM MOULD OPENING STROKE: 410MM MAX DAYLIGHT: 910MM EJECTOR STROKE: 150MM CONTROLS: DIMI EL 2000 AIR VALVES: 1 MOTOR: 15 HEATING CAPACITY: 9.3KW SCREW DRIVE: HYDRAULIC

Displacement: 1500 cm³ Clamping force: 2500 kN Injection pressure: 2000 bar Table height: 1,000 mm Locking system: fully hydraulic Voltage: 380 V Motor power: 26 kW Cooling water: 1 m³/h Weight: 5.5 t - Injects from above (type ZO) - Ergonomic overall design of the vertical machine - Generously dimensioned clamping unit - Extensive automation options for vertical machines - "One Piece Design" for maximum flexibility The machine belongs to a German company and until recently was in operation at their Serbian plant and ran flawlessly.

Table height: 1000 mm Locking system: fully hydraulic Clamping force: 2500 kN Spray volume: 1500 cm³ Hydraulic oil: 40/46 cPcs. Compressed air: 6 bar Voltage: 400 V Weight: 6.35 t - Injects from below (type VU) - Ergonomic overall design - Generously dimensioned clamping unit - Fully hydraulic extensive automation possibilities of vertical machines - "One Piece Design" for maximum flexibility The machine belongs to a German company and until recently was in operation at their Serbian plant and ran flawlessly.

Article number: 27-06-304 Manufacturer: Arburg Very good general condition Machine workshop-tested Shipping time: All rights reserved. Year of construction: ca.1985 L x W x H: approx. 2700x1200x1800mm Weight: approx. 930kg Closing side: Clamping force: approx. 250kN Holm dimension hxv: ca.221x0mm Plate size hxv: approx. 342x250mm Installation height min: ca.150mm Installation height max: approx. 300mm Plate spacing max: approx. 500mm Aperture travel: approx. 200mm Spray side: Screw diameter: approx. 22mm Displacement: approx. 38cc Injection pressure: approx. 1500bar Other accessories on request Price and other technical data on request

Engel ES 1350/300 HL Year of construction 2001 + 2003 Hours: 77623 h + 92737 h Clamping force: 300 tons. Screw diameter: 70 mm 4 core pulls incl. Wittmann removal robot  ... more information

Arburg 270U-250-70 (221) Description General information SKU: (221) Availability: In stock Year of construction: 2005 Brand: Arburg Specifications Injection weight: 20 g Clamping force: 250 kN Stand: Used Screw diameter: 18 mm Injection pressure: 2500 bar Tie bar spacing: 270 x 270 mm Clamping plate size: 380 x 380 mm Tool installation height min.: 200 mm Control: Selogica Language: German Power: 35 kW Operating hours: 82,985 h Curmtbe2w8 Weight: 2100 kg Dimensions: 3m x 1.1 m Funnel: No Core Train: Yes Euromap: Yes

We have in our workshop and awaiting refurbishment this BOY 22D. The machine is a compact 22 tonne clamp machine with a very easy to use controller with the Dipronic system. These machines have stood the test of time and remain very popular as they are simple to use, cheap to repair and reliable. Machines awaiting refurbishment can be reserved with a small deposit and the refurbishment is then prioritised and scheduled. Refurbished machines from STV Machinery undergo a comprehensive test procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. Machines are ultra clean and cosmetically as good as we can get them. We guarantee our refurbs are delivered fault free and leak free. Category: Injection Moulding ID: 12646 Manufacturer: ...

Awaiting refurbishment at our works in Wellingborough, Northamptonshire is this high precision BOY 12A injection moulding machine. Fitted with the Procan controller. The 12A from BOY is one of the most common small moulding machines we see, it is extremely accurate while still maintaining versatility with tooling and familiar control setup. Refurbished machines from STV Machinery undergo a comprehensive test procedure during which every function of the machine is tested and if necessary repaired. A production run of at least 5000 fault free cycles prior to sign off ensures trouble free operation once delivered. Machines are ultra clean and cosmetically as good as we can get them. We guarantee our refurbs are delivered fault free and leak free. Category: Injection Moulding ID: 12882 Manufacturer: BOY Model: 12A Datasheet (PDF): View Here Viewing: Not yet refurbished Condit ...