Manufacturer:
(Category: 503)
Inlet: approx. 600 x 580 mm Rotor width: approx. 600 mm Rotor diameter: approx. 450 mm Stator knives: 2 Rotor blades: 4 ... more information
Inlet opening: approx. 400 x 400 mm Rotor width: approx. 400 mm Rotor diameter: approx. 400 mm Stator knives: 3 Rotor blades: 3 Drive: 18.50 kW Feed opening: approx. 400 x 400 mm Rotor width: approx. 400 mm Rotor diameter: approx. 400 Stator knives: 3 Rotor knives: 3 Drive: 18.50 kW ... more information
Inlet: 1200 x 950 mm Rotor width: 1200 Rotor diameter: 800 Stator knives: 4 Rotor blades: 7 x 4 ... more information
WEIMA shredder for carpentry-carpentry sawmill waste -old wood etc. Type:WL 4. Feeding opening: 600x1050.mm. ( Log Funer ) Rotor diameter:252.mm. Rotor width:600.mm. Drive power:18.5kW. Tools: ( Knife piece 28.) 40x40.mm. Koncav Vs9lrq Weight:1300.kg. ... more information
Shredder for green waste, biomass, roots, bulky waste, waste wood, commercial waste, etc., equipment: radio remote control, hydraulic travel drive, overbelt magnet, auxiliary hydraulics, humidification for dust binding for external water connection, service and tools new. SPECIAL FEATURE: Engine original MTU- Mercedes NEW due to dust damage.
Shredder for green waste, biomass, roots, bulky waste, waste wood, commercial waste, etc., equipment: radio remote control, hydraulic travel drive, overbelt magnet, auxiliary hydraulics, humidification for dust binding for external water connection, service and tools new. SPECIAL FEATURE: Engine original MTU- Mercedes NEW due to dust damage.
Pre-shredder for garbage, waste wood, green waste, roots, commercial waste etc., five travel drives, auxiliary hydraulics, SPECIAL FEATURE: Engine, hydraulic system and electrics new after fire damage, service and tools new or as good as new. ... more information
Shredder for green waste, roots, waste wood, reed wood, organic waste, biomass, bark, etc. Equipment: Radio, hydraulic travel drive, overbelt magnet, SPECIAL FEATURE: Both shredding shafts, basket carrier with bio-cutting unit, baskets, tools, large service renewed before 100 hours of operation original Komptech.
Pre-shredder / shredder / chopper Fabr. Piranha for wood and plastic Motor 37 Kw Shaft length 600 mm with 3 x 5 Schneider knife with sieve 35 mm with control ... more information
JMC 900 alligator shears (new machine) The JMC 900 has a hydraulic hold-down. The scissor head is operated with a foot pedal for individual cuts or continuous cutting. The scissor head is protected with a safety basket. Out of stock Delivery time: On request Manufacturer: Mc Intyre Knife length: 920 mm Measuring opening: 473 mm Cutting capacity: 233 tons Round iron ST 37: 88 mm diameter Number of strokes at 1/4 aperture: 26 / min Number of strokes at full opening: 9 / min Dimensions ( L x W x H ): 3200 x 1030 x 1800 mm Weight: 4400 kg Drive: 18.5 kw / 400 V + 1.5 kw electric motor cooler Operation: Foot pedal
Alligator scissors Lindemann Alibo The Lindemann Alibo has a mechanical hold-down. The scissor head is protected with a safety basket. Machine On hand Knife length : 760 mm Weight : 4200 kg Mouth width at the tip : 200 mm Cutting capacity: 0.45 kN/ mm² : Ø 70 mm Number of strokes : 20 – 40 cuts/min Dimensions: 4.20 x 1.50 x 1.80 meters Drive: 15 kw Hold-down: Mechanical
The JMC 150 has a mechanically adjustable hold-down. The scissor head is operated with a foot pedal for individual cuts or continuous cutting. The scissor head is protected with a safety basket. The JMC 150 is a tabletop unit for easy handling. Manufacturer: Mc Intyre Knife length: 150 mm Measuring opening: 105 mm Cutting capacity: 25 tons Round iron ST 37: 25 mm diameter Number of strokes at 1/4 aperture: 20 / min Number of strokes at 1/2 opening: 12 / min Number of strokes at full opening: 9 / min Dimensions ( L x W x H ): 660 x 520 x 620 mm Weight: 150 kg Drive: 1.5 kw / 230 Volt Operation: Foot pedal
Used JMC 407 Kat Alligator Scissors Alligator scissors JMC 407Cat The catalyst version JMC 407 has an additional "V-holder" in the cutting area for adjustment when cutting or opening the catalysts. In stock at the end of March 2021 Knife length: 407 mm Measuring opening: 250 mm Cutting capacity: 90 tons Round iron ST 37: 57 mm diameter Number of strokes at 1/4 opening: 63 / min Number of strokes at full opening: 11 / min Dimensions (L x W x H): 1550 x 880 x 1120 mm Weight: 880 kg Drive: 7.5 kw / 380 V Operation: Foot pedal
Manufacturer: Deltax Holder: Hydraulic holder Dimensions (L x W x H): 2010 x 902 x 1500 mm Knife length: 610 mm Number of strokes at 1/4 opening: 40 cuts at quarter opening Number of strokes at full opening: 12 cuts at full opening Measuring opening: 330 mm Cutting force: 206 tons Drive: 11 kw/32 CEE plug Weight: approx. 2250 kg Deltax_DTX600S with hydraulic holder (New machine) The DTX 600S has 20% more cutting power than the standard Deltax DTX600. This was achieved by installing a larger cylinder and using a smaller second pump. A larger first pump is used to maintain the same cutting speed. All other modifications are used to amplify the machine to handle the additional power. The weight gain due to the reinforcement modifications and the larger pestle is about 250 kg. Alternatively: Deltax DTX600 Difference Cutting force: 172 tons | Weight: 2000Kg | All othe ...
Manufacturer: Mc INTYRE Blade length: 150 mm Blade opening: 105 mm Cutting capacity: 25 tons Rods ST 37: 25 mm diameter Number of strokes at ¼ opening: 20 / min Number of strokes at ½ opening: 12 / min Number of strokes at full aperture: 9 / min Dimensions (L x W x H): 660 x 520 x 620 mm Weight: 150 kg Drive: 1.5 kw / 230 Volt Control: foot pedal
Small but very robust and powerful shredder for a wide range of tasks such as old cables, plastics, wood, etc. With hydraulic, electronically controlled feed. Drive 18.5 + 2.2 kW (rotor + feed). Rotor shaft with connections for connecting a cooling unit (e.g. when used for old NYM cables. The machine is and little used from our demo machine inventory. The machine is offered with a one-year used machine warranty.
Small shredder for various tasks such as old cables, plastics wood, etc. With hydraulic, electronically controlled feed. Drive 18.5 + 2.2 kW (rotor + feed). Rotor shaft with connectors for connecting a cooling device (e.g. when used for NYM old cables. The machine is 1 year old and little used from our demo machine inventory. The machine is offered with a one-year used machine warranty.
Small shredder for a wide range of tasks such as old cables, plastics wood, etc. With hydraulic, electronically controlled feed. Drive 18.5 + 2.2 kW (rotor + feed). The machine was overhauled by the manufacturer ISVE in September 2020 and supplemented with an electronics for networking into a cable recycling line. A rotor cover for the optimized processing of old cables has also been added. Currently, the shredder has a 16 mm hole sieve but other hole diameters can also be added. With the 16 mm hole sieve, the shredder reaches about 250 kg/hour when processing mixing cables.
Large Four Shaft Shredder with Two Cutting Shafts and Two Feed Shafts. Until now, the shredder has been used as a pre-shredder for the recycling of old cables. Due to the hydraulic tamper, the shredder can also be used for bulky materials. Changing the screens is hydraulically assisted and therefore easy to do. On request, the shredder can also be supplied with the articulated conveyor belt shown here. The conveyor belt is equipped with a magnet in the upper pulley for iron separation.
The MR 40-80 is a powerful single-shaft shredder for many tasks, such as the pre-shredding of cables, the crushing of electronic waste, used plastics, wood, etc. Unlike other single-shaft machines, IRS's shredder has two instead of one series of stator knives for better product quality and higher hourly output. The optimized arrangement of the rotor blades also reduces energy consumption. The horizontally acting hydraulic pusher has replaceable wear strips and regulates the contact pressure on the rotor. In addition, there are interchangeable screens for special tasks from 10 mm hole diameter. On request, the shredder can be optimized for cooling the rotor shaft, with wear protection armor, hydraulic clutch, remote services and other options for the respective application. Specifications: Number of knives: 35 + 2 (rotor + stator) Rotor speed: 85 rpm Rotor Ø, length: 400 mm, 80 ...