Manufacturer:
(Category: 106)
Eccentric press vineyard type AR160 tons With protective shield. YOC 1971 2 rotational speeds via mechanical gearbox Switchable. Central lubrication. Low-wear steep-threaded coupling. Table dimensions : 800x1000 mm Visits : possible at any time. Total weight approx. 10.5 tons ... more information
PRESS DESIGN drive system: knuckle-joint feedstock transport direction: right to left SLIDE total force (nominal): 80 to stroke: 50 mm stroke rate (max.): 70 /minCOUNTER RAM nominal force: 22 toV-RING nominal force: 25 toTOOL DIMENSIONS lower table (left-right): 430 mm lower table (front-back): 490 mm upper table (left-right): 420 mm upper table (front-back): 420 mm shut height max.: 230 mm ram adjustment: 80 mm distance between columns (H-frame): 450 mm passline opening (free passage in side columns): 200 mmOVERALL SPECIFICATIONS (COIL LINES) sheet width max.: 180 mm sheet thickness max.: 5 mmSTRIP-FEEDER feeder type: roll feeder sheet width max.: 180 mm sheet thicknes ...
CONTROLS PLC BECKHOFF SLIDE total force (nominal): 80 to stroke: 50 mm stroke rate (min.): 28 /min stroke rate (max.): 70 /minV-RING nominal force: 25 toCOUNTER RAM nominal force: 22 toTOOL DIMENSIONS lower table (left-right): 420 mm lower table (front-back): 420 mm upper table (left-right): 420 mm upper table (front-back): 420 mmSTRIP-FEEDER feeder type: roll feeder sheet width max.: 200 mm sheet thickness max.: 5 mm feeding step min.: 0 mm feeding step max.: 999 mm pilot release system: yes measuring wheel: optional ELECTRICAL SPECIFICATIONS mains voltage: 400 V mains frequency: 50 HzATTACHMENTS -FINEBLANKING PRESS- waste cutter: yes Example of an overhaule ...
CONTROLS PLC SIEMENS S7 PRESS DESIGN drive system: link drive feedstock transport direction: left to right SLIDE total force (nominal): 80 to stroke: 50 mm stroke rate (max.): 80 /minCOUNTER RAM nominal force: 22 to stroke: 8 mmV-RING nominal force: 25 to stroke: 15 mmTOOL DIMENSIONS lower table (left-right): 420 mm lower table (front-back): 420 mm upper table (left-right): 420 mm upper table (front-back): 420 mm shut height max.: 220 mm ram adjustment: 80 mm distance between columns (H-frame): 450 mm passline opening (free passage in side columns): 200 mmOVERALL SPECIFICATIONS (COIL LINES) sheet width max.: 180 mm sheet thickness max.: 5 mm feed velocity max. ...
pressure: 200 tpassage width: NA mmstroke: 180 mmtable length: 690 mmtable width: 530 mmdistance between columns: 420 mmtotal power requirement: 18 kWweight of the machine ca.: tdimensions of the machine ca.: mHydr. 4-Pillar Press for Embossing/CalibrationThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure:63 tthroat:325 mmstroke:560 mmdistance table/ram, max. stroke up, adjustment up:700 mmtable surface area:640 x 640 mmpressure of drawing cushion in table:25 tstroke of drawing cushion in table:200 mmdie cushion area:450 x 450 mmtable height over floor:800 mmram surface:560 x 560 mmoil volume:450 lpower requirement:15,0 kWweight:7,0 tdimensions (WxDxH):1,2 x 2,0 x 3,1 mGerman Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 drawing cushion in table:hydraulic
Max. pressing force 60 to Installation height 500 mm Stroke of the press ram 300 mm Passage between the columns 430 mm Pusher bore 40D H7 Clamping table 430 x 310 mm ... more information
Description: Rated capacity 4050 x 200 T Stroke 250 mm Weight 19 T Rebuilt and brought into compliance by Descombes Précimeca in 09/2016weight approx.: 19,000 kg, Approx. Onsite Dimension. (l x w x h): 4,200 x 1,600 x 3,000 mm ... more information
pressure: 16 tthroat: 185 mmstroke: 8-60 mmno. of strokes: 140 Hub/minram - range of adjustment: 50 mmtable surface area: 500x340 mmram surface: 230x155 mmhole in the table: Ø160 mmtable height: 800 mmhole in the table: Ø35 mmweight of the machine ca.: 1,5 tdimensions of the machine ca.: 1200x1200x2000 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 15 tthroat: 190 mmstroke: 6-80 mmstroke: 8-60 mmno. of strokes: 140 Hub/minram - range of adjustment: 60 mmtable surface area: 590x400 mmram surface: 230x180 mmhole in the table: 200x140 mmtable height: 800 mmtool hole in ram: Ø 40 mmweight of the machine ca.: 1 tdimensions of the machine ca.: BxTxH 1000x1000x2000 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Capacity: 160 ton Throat depth: 350 mm Ram stroke: 20 - 140 mm Slide adjustment: 75 mm Shut height (stroke down, adjustment up): 740 mm Table surface area : 1000 x 680 mm Slide area: 600 x 300 mm Number of strokes: 50 s.p.m. Required power: 15 kW Weight of machine approx.: 12 ton ... more information
pressure: 100 tthroat: 300 mmstroke: 10-100 mmno. of strokes: 80 Hub/minram - range of adjustment: 60 mmtable surface area: 900x600 mmram surface: 800x230 mmhole in the table: 300x200 mmtool hole in ram: Ø 50 mmweight of the machine ca.: 4,0 tdimensions of the machine ca.: 1700x1500x2700 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure:150 tdistance between columns:300 mmstroke:180 mmdistance table/ram, max. stroke up, adjustment up:300 mmtable surface area:570x180 / 300x410 mmtable height over floor:875 mmside window:180 mmram surface:180 mmspeed down:250 mm/sspeed up:160 mm/sworking speed:6 - 12 mm/soil volume:250 lpower requirement:11,0 kWweight:2,4 tdimensions (WxDxH):1,3 x 1,3 x 2,4 mGerman Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 § 20 foundation pit:nicht erforderlich
Pressure:800 tdistance between columns:3250 mmstroke:1100 mmDistance table/ram, stroke up:1900 mmTable surface area:3100 x 1900 mmpressure of drawing cushion in table:300 tDie cushion stroke in table:300 mmDie cushion area in table:2500 x 1800 mmDie cushion pressure in ram:80 tDie cushion stroke in ram:200 mmDie cushion area in ram:2200 x 1000 mmRam surface:3100 x 1900 mmSide window:900 mmOil volume:4700 lPower capacity:200,0 kWDimensions (WxDxH):4,95 x 3,3 x 10,2 mHeight above floor:7,05 mdie cushion in table:hydraulic, controllable die cushion in ram:hydraulic, controllable cutting impact absorption:hydraulic
Article code: 13-13-023 Manufacturer: Neher Very good general condition Machine workshop-tested Shipping time: All rights reserved. Year of construction: ca.1972 L x W x H: approx. 1600x1600x2300mm Weight: approx. 1200kg Max. pressing force: approx. 20 tons Wheel Diameter: ca.1600mm Working stroke: approx. 300mm Other accessories on request Price and other technical data on request
Article number: 13-13-024 Manufacturer: Reyer Very good general condition Machine workshop-tested Shipping time: All rights reserved. Year of construction: ca.1972 L x W x H: approx. 1200x800x2000mm Weight: approx. 400kg Max. pressing force: approx. 20 tons Table surface: approx. 420x530mm Other accessories on request Price and other technical data on request
Force of pressure: 75 t projection: 300 mm table size: 620 x 800 mm Durchfalloch in the table: 225 x 325 mm table adjustment: 175 mm plunger surface: 180 x 475 mm slide adjustment: 80 mm stroke adjustment: 16-140 mm stroke rate: 90 / min drive motor: 380 V, 3 kW space: 1700 x 1200 x 2500 mm weight: 3300 kg
Description: Machine is currently working in conventional operation. Documentation available Pressure 70 t Bending length 3000 mm Stand width 2550 mm Ram stroke 120 mm Projection 200 mm Total power requirement 7.5 HP Machine weight approx. 5.6 t Space requirement approx. 3.6 x 1.9 x 2.4 mweight approx.: 6,000 kg, Approx. Onsite Dimension. (l x w x h): 3,500 x 1,700 x 2,400 mm
nominal force:315 tstroke:300 mmno. of strokes:36 /mindistance between columns:540 mmdistance table/ram, max. stroke up, adjustment up:750 mmtable surface area:530 x 630 mmblow die to die:630 tAllowed max. force:500 tram surface:450 x 560 mmspindle diameter:180 mmpower capacity:18,0 kWweight:13,0 tDimensions (WxDxH):2,5 x 2,0 x 4,0 m
pressure: 160 tdistance between columns: 850 mmstroke: 150 mmtable surface area: 850x650 mmtotal power requirement: kWweight of the machine ca.: 7 tdimensions of the machine ca.: 2,5 x 2,5 x 3 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... more information