subcategories
(3rd category level)
Manufacturer:
(Category: 107)
material width:250 mmcoil weight:2,5 tcoil internal diameter:430 - 520 mmcoil external diameter:1650 mmmaterial thickness:0,5-6 mmno. of straightening rolls:7 straightening roll diameter:60 mmnumber of draw-in rolls:2 weight straightener:1,2 tweight decoiler:1,4 tdimensions straightener (WxDxH):1,2 x 1,2 x 2,0 mdimensions decoiler (WxDxH):1,8 x 1,8 x 2,3 mexpansion:hydraulic
material width:203 mmmaterial thickness:0,1 - 1,9 mmfeed length:101 mmweight:0,1 tdimensions (WxDxH):0,5 x 0,8 x 0,5 m ... more information
material width:450 mmmaterial thickness:1,0 - 14,0 mmcoil weight:10,0 tcoil internal diameter:470 - 520 mmcoil external diameter:1100 - 2000 mmno. of straightening rolls:12 straightening roll diameter:2x70 / 2x96 / 8x127 mmnumber of draw-in rolls:2 inlet roll diameter:160 mmmin. material width:100 mmspeed:15 m/minpower requirement:75,0 kWweight of decoiler:6,4 tweight of straightening machine:12,8 tdimensions decoiler (WxDxH):3,1 x 1,4 x 3,7 mmdimensions straightener (WxDxH):2,5 x 3,4 x 2,7 mmstraightening machine:RMS-Vario-12-70/96/127-0450 infinitely variable drive:insert drive upper straightening part:hydraulic liftable loop bridge:hydraulic driven threading wedge:hydraulic decoiler:HES 12-650 infinitely variable drive:insert drive lag brake:pneumatic snubber roll:hydraulic; motoric driven expansion:hydraulic coil lifting device:hydraulic cropping shears:HS-150-0450
material width coil line:600 mmcoil weight in kg:2 x 3000 kgcoil internal diameter:460 - 630 mmcoil external diameter:1500 mmmaterial thickness coil line:0,5 - 3,0 mmNumber of Straightening rolls:9 roll diameter:30 mmmaterial cross-cut:1200 mm²weight:9,5 tDimensions (WxDxH):4,3 x 2,6 x 2,6 mstraightening machine:30.600/9 double decoiler:Kohler, 3000.2 ausiliary drive:hydraulic lag brake:pneumatic expansion:hydraulic snubber roll:hydraulic; motoric driven
sheet width:400 mmplate length:500 mmplate thickness:4 mmtotal power requirement:0,5 kWPunching and Nibling machine with 6 x 3 mm nibling and 4 mm for cuting ... more information
material width:250 mmmaterial thickness:0,5 - 4,0 mmno. of straightening rolls:9 straightening roll diameter:60 mmnumber of draw-in rolls:2 power requirement:3,8 kWWeight:0,8 tDimensions (WxDxH):1,6 x 0,8 x 1,5 m ... more information
material width:500 mmcoil weight:3,0 tmaterial thickness:0,2 - 2,5 mmcoil internal diameter:470 - 530 mmcoil external diameter:1400 mmno. of straightening rolls:9 straightening roll diameter:40 mmnumber of inlet and outlet rolls:4 material cross-cut:1200 mm²speed:1,5 - 30 m/mindimensions decoiler (WxDxH):1,9 x 0,6 x 1,7 mweight decoiler:1,1 tdimensions straightener (WxDxH):3,3 x 1,3 x 2,7 mweight straightener:3,0 tstraightening machine:RYD 40 x 500 decoiler:DY 500 x 3000 coil lifting device:hydraulic rool feed:elektronic; AESL 500-2,8 threading device:hydraulic expansion:hydraulic
sheet width:5040 mmplate thickness:2 mmtotal power requirement:12 kWweight of the machine ca.:9,4 tdimensions of the machine ca.:6200× 1300 ×1900 mmworking width:5000 mmcontrol:Fasti Matik stroke of upper beam:500 mmadjustment of lower beam:u.Biegewange 80 mmcontrol cabinet:1000 x 850 x1450 mmDocuments:vorhanden
material width:600 mmmaterial thickness: - 4,0 mmno. of straightening rolls:21 straightening roll diameter:30 mmmaterial cross-cut:1800 mm²speed:6 - 36 m/minPower capacity:4,5 kWWeight:2,0 tDimensions (WxDxH):1,5 x 2,0 x 1,9 m ... more information
material width:70 mmmaterial thickness:0 - 1,5 mmfeed length:100 mmmaterial cross-cut:60 mm²feeding force:400 Nclamping force of feeding pincer:1300 Nair pressure - required:3 - 6 barWeight:0,01 tDimensions (WxDxH):0,4 x 0,4 x 0,7 m ... more information
sheet width:3100 mmplate thickness:6 mmtable length:3400 mmtable width:490 mmtable height:800 mmstroke:18 pro Min.quantity of oil:150 lNumbers of downholders:14 cutting angle:1,2 °total power requirement:11 kWweight of the machine ca.:5,5 tmot.digital controlled backgauge, workspace:1000 mm:1000 mmfront support arms with T-slot and flip cams:1000 mm
sheet width:3100 mmplate thickness:6 mmdistance between columns:3100 mmno. of strokes:16 - 24 Hub/mincutting angle:0,5 - 1,5 °down holder:14 Stk.throat:350 mmtable height:900 mmoil volume:150 ltotal power requirement:11 kWweight of the machine ca.:7060 kgdimensions of the machine ca.:4100 x 2200 x 2190 mm1 brandnew hydraulic shear ERMAK CNC HVR 3100-134 with following equipment:- CNC controlled hydraulic blade gap adjustment system- CNC controlled cutting angle adjustment system- portable foot pedal- CNC controlled motorized backgauge system- front support arms with t-slot, ruler and flip stop- squaring arm- scales with metric and inches- cutting line illumination and shadow line- emergency stops- swing up backgauge- central lubrication system- front finger protection - rear sliding plates- front sliding plates with ball bearing on the table- 350 mm throat depth- pendant controller arm
pressure:320 tchamfer lenght:4100 mmdistance between columns:3600 mmcolumn arm:410 mmram stroke speed:140 mm/secreturn speed:150 mm/secworking speed:10,5 mm/secwork stroke:375 mmdayligth:650 mmtable height:900 mmtable width:220 mmoil volume:400 lvoltage:400 Vtotal power requirement:30 kWweight of the machine ca.:22600 kgdimensions of the machine ca.:5350 x 2450 x 3150 mm1 brandnew ERMAK SPEED-BEND 4.320 hydr. press brake, directly from the factory, with DELEM DA 66 T CNC control and following equipment:- controlled back gauge with R-axis X = 800 mm R = 250 mm- finger adjustment Z1 + Z2 through ball screw- 2 front support arms - controlled axis Y1-Y2-X-R-Z1-Z2 + CNC-crowning system4- top tool - 4V universal die-block- BOSCH/HOERBIGER hydraulic system- SIEMENS electronic- SICK light barrier- FISSLER AKAS laser-light barrier- double foot switch- CE mark / conformity declaration- operation ...
sheet width:2000 mmplate thickness:1.8 mmControls:SIEMENS S7 PRESS DESIGN:. - frame design : H-frame :. - openings in uprights : yes :. - opening in table : yes :. - moving bolster : yes :. PRESS TABLE:. - clamping surface (left-right):2800 mm - clamping surface (front-back):2800 mm - height above floor level:375 mmRAM:. - ram force:800 to - clamping surface (left-right):2800 mm - clamping surface (front-back):2800 mm - stroke:350 mm - number of strokes max:55 /minRAM (MECHAN. PRESS):. - ram adjustment:350 mmTOOL ASSEMBLY DIMENSIONS:. - shut height (stroke down, adjustment up):1100 mm - distance between columns (H-frame):3100 mm - Free passage between side columns (width):2560 mm - Free passage between side columns (height):1500 mmDECOILER:. - design : single coil :. - sheet width max:2000 mm - sheet width (min):400 mm - max. weight of coil:30 to - max. di ...
pressure: 170 tchamfer lenght: 4080 mmdistance between columns: 3680 mmcolumn arm: 410 mmdayligth: 385 mmstroke: 215 mmajustment speed: 200 mm/secworking feed: 1-10 mm/secreturn speed: 135 mm/sectable width: 200 mmtable height: 1050 mmtravel -x axis: 600/860 mmNumber of working hours: ~ 23.280 hoil volume: 350 ltotal power requirement: 29 KVAweight of the machine ca.: 16.450 kg.range L-W-H: 4620 x 2210 x 2885 mm Machine in a well-maintained condition ()Furnishing:- CNC electro-hydraulic press brake/die bending press- DELEM CNC control - swiveling at the front left high resolution graphic screen Clear, concise menus in the operators language Large tools and products library 2D graphical programming automatic bending sequence calculation and collision detection EMERGENCY stop button at the front- CNC axis adjustment: Y1 - Y2 - X - R - Z1 - Z2 axis- X axis - adjustment speed: 500 mm/sec. Ma ...
own weight: 6.8ton; Including pallet parts ... more information
Description: Serial Number: A15.564 CNC : TRUMPF Main Drive , Punching Force : 180 KN Max. sheet thickness: 6.4 mm Strokes: ,  ,X-AXIS: 1250 mm  ,Y-AXIS: 1280 mm Max. workpiece thickness , Steel: 4 MM Max. workpiece weight: 75 kg , Max. workpiece height: 38 mm , Programmable force: 4000-17000kn Speeds: , X-axis: 90 m/min Y-axis: 60 m/min Simultaneous: 108 m/min Power: 400 V / 50 HZ Installed power: 17 KVA Important note: , The machine is currently stored as shown in pictures 5-12.  ,max. punching diameter: 76 mm, weight approx.: 9,200 kg, Approx. Onsite Dimension. (l x w x h): 5,530 x 2,300 x 2,255 mm
Description: .DIMECO R 693 J+ sheet metal straightening machine y.o.m 2020! - Number of straightening rollers 17 - Number of pull rollers 2 - Pull rollers diameter 180 mm - Number of support rollers 147 - Largest roller distance 200 mm The machine is equipped with: - Control cabinet with drive outlets for height adjustment on the inlet/outlet side of the straightening cassette as well as for the two main drives connected in parallel - Hydraulic unit for the hydr. Movements of the infeed table and the delivery of the infeed driver - Support rollers firmly installed at the top and bottom - Documentation, digital only! - Additional, unused straightening roll cassettes with 17 straightening rolls and intermediate rolls at the top and bottom. The machine was until lately integrated into a fully automatic punching line, therefore it is necessary to complete the control system. There is alr ...
Description: Max. cutting length 6000 mm, estimated material thickness 6 mm, cutting gap, backgauge and material thickness can be entered via digital display, for further details see photosplate thickness: 6 mm, weight approx.: 24,000 kg, Approx. Onsite Dimension. (l x w x h): 8,000 x 2,500 x 2,600 mm