subcategories
(3rd category level)
Manufacturer:
(Category: 107)
Max. bending length: 1500 mm Max. sheet thickness: 10 mm steel Upper roll diameter: 195 mm Includes rollers for rolling flat steel Clockwise and anticlockwise rotation via hand-held control unit ... more information
Type: UBR 25 x 2000-7 / 16 Manufacturer / make: WMW Wildau Baujahr / year: 1984 max. sheet width: 2000 mm max. sheet thickness ( St 50): 25 mm min. sheet thickness / min. sheethickness: 8 mm Number of straightening rollers: 7 rollers Weight of the machine / weight: 51 t ... more information
FEEDSTOCK TUBE external diameter min.: 25 mm external diameter max.: 55 mm length min.: 3500 mm lenght max.: 10000 mmPRODUCT (PROFILE, TUBE) length min.: 5000 mm lenght max.: 13500 mmCHARACTERISTICS DRAWING MACHINE force: 320 kN drawing length max.: 13500 mm number of parallel trains / strands max.: 3 speed max.: 100 m/minFunction: Automatic (manual threading, pull chain runs forwards and backwards, front bench can be swiveled vertically)Products: Round tubes (mostly shock absorbers), semi-finished or finished productsModernized: 1999 new pulling belt and brake2022 pulling chain partially renewedmax. drawing rod / pointed end diameter: 40 mmmin. drawing rod / pointed end diameter: 14 mmmax. drawing rod / pointed end length: 170 mmmin. drawing rod / pointed end length: 150 mmnumb ...
: 40 mm: 3 mm: 30 - 120 Gradblade length: 150x150 mmwork height max.: 900 mmwork table:: 600x450 mmweight: 400 kgrange L-W-H: 800x910x800 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... more information
Max. pressing force: 250kN, stroke: 13-38mm, stroke speed: 875-1500/min, connected load: 20kW. ... more information
hydraulic concrete steel Benders Krupp Futura B 703 steel bending machine with accessories and complete instructions Tech. Data performance table - steel 50-55 kp/mm2 Diameter 22 mm - 6 bars per bending, 28 mm-4, 32 mm 3,. Mtfgtw 50 mm 2 speed 4-12 / min Operation - with control or manual, operating dial - HAND - machine with possibility of 3 bending angle set - every page - 3 links + 3 right complete documentation, operating instructions much accessories more info upon request You can edit, flat, round steel accessories - various bending rollers, bolts, reducing roll, Overarm and the machine has device for Pipes. Bulk 2.3 x 1 x 1 m, Btto 1500 kg
Max. bending length 3000 mm Max. pressure 160 Ton Distance between side frames 2550 mm Length of stroke 200 mm Control DELEM DA 24 e Equipped with: Motorized back gauge Upper dies Bottom dies Segments Foot contact 2-hand operated Service tools etc. ... more information
Technical data approx.: - Total load capacity driven + rotating unit 25000 kg - Payload per container device 12500 kg - Workpiece diameter approx. 500 - 4000 mm - Axle distance of the support rollers adjustable - Roll diameter 400 mm - Roll width 120 mm - infinitely adjustable rotational speed - Handheld remote control for re- and li. run - Drive 400 V - Space requirements Unit approx. W 3500 x H 850 x D 1000 mm - Platzb. with running unit approx. W 2700 x H 850 x D 800 mm - Weight applied Unit approx. 1300 kg - Weight with running unit approx. 900 kg
Tech. Data VS 4 maximum strip width 250 mm, maximum advance length 400 mm Max band thickness 2.5 mm maximum band cross-section 600 mm2 Holding power sled pliers - up to 1,6 t Holding force holding pliers - up to 1 t Thrust - up 0.4 t Damping - hydraulic Feed accuracy +-0.01 mm (distance) Tech. Data VS 3 Max. Band width 160 mm maximum advance length 230 mm Max. Band thickness 2.5 mm, max. band cross-section 400 mm2 Holding force slide clamp up to 900 kg Holding pliers up to 600 kg, feed capacity 240 kg complete with instructions, control, cam
Specifications: - Max. cutting width 3050 mm - Max. cutting capacity at 45 Kp/mm² 6 mm - Cutting angle adjustment 1 - 2.20 ° - Cutting gap - adjustment via lateral adjustment lever - Number of hold-downs 16 pcs - Stroke rate up to 22 /min - Front angle stop 1100 mm - 2 front support arms 600 mm -Mot. Backgauge with ELGO positioning control - 5 - 1000 mm - Cut line illumination - E – Footswitch - Drive 400 V / 12 kW - Space requirement approx. W 4100 x H 1500 x D 2200 mm - Weight approx. 5.0 t
Type 509, with pneumatic sheet metal holding Adjustable cutting length, cutting angle and cutting gap 5 table extensions / angle stops approx. 6000 kg ... more information
Technical data: -Bending mot. Automatic or manual mode -Bending performance square steel ST 37 up to approx. 25 mm -Bending performance ST 37 steel up to approx. 30 x 8 mm -Bending length betw. the adjustable 1000 mm turning units -Faceplate with various recording profile perforations -Tailstock / recovery storage -Delay start bending / bending length twisting preselection - right - left rotation -Space requirement approx. B 1750 x H 1100 X 500 mm -Drive 400 V / 0,75 kW -Weight approx. 150 kg
Notching machine Indumasch Model 284 Year of construction 1985 Knife length 280x280mm Cutting capacity 4mm at R-42 Kg/mm2 3mm at R-70Kg/mm2 Work table 1000x800 60 strokes per minute Weight 950Kg A viewing under power is possible by appointment The offer is aimed exclusively at traders within the meaning of §14 BGB No sale to private individuals!
UBBDA Three Roll Plate Bending Machine The three-roll sheet bending machine is designed for the production of cylindrical and conical sheet shells. Electric motors 42 kW, 580 rpm, 750\1500 rpm Dimensions 12900x5300x5620 Gross weight 166260 t ... more information
Offer 23278 Specifications: - Sheet metal and flat steel shears, knife length 175 mm - cuts flat steel up to 50 x 15 mm - or up to 140 x 8 mm - Profile - steel bar shears - cuts - angle steel up to 80 x 8 mm - Round steel up to 28 mm - Square steel up to 25 mm - Hole punch - punching force 275 KN - Stroke 24 mm - Projection 155 mm - perforated in steel up to 20 Ø in 10 mm - or up to 27 Ø in 6.5 mm - Drive 400 V / 3 kW - Space requirement approx. W 500 x H 1500 x D 855 mm - Weight approx. 450 kg - various punches + matrices
For cannibalization I offer a powerline 25-500, built in 1985, which works until the end Machine can no longer be tried; already partially dismantled. In 2017 both servo cards were new! Invoice available ... more information
Description: Machine number: 10 Incl. various attachmentsweight approx.: 1,000 kg, Approx. Onsite Dimension. (l x w x h): 1,300 x 1,200 x 1,700 mm ... more information
CONTROLS PLC SIEMENS S7 300 Main spindle DIN 55022 size 11Crosshead spindle DIN 55022 size 8Drive power main spindle 30.7 KWDrive power hydraulics 33.5 KWMain spindle speed 350 - 1000/minWorkpiece diameter max. 650 mmCrosshead stroke 300 mmEjector stroke 80 mmCrosshead contact force 400 kN
Technical data: - bending and rolling by hand, - max working width 1020 mm - max. material thickness St 40 1.25 mm - Bending angle adjustment via end stop 10 - 180 ° - max hub upper cheek approx. 85 mm - max. adjustable bending cheek 20 mm - Shaft diameter 55 mm - Upper shaft can be swivelled - Rear shaft parallel + obliquely adjustable - Space requirement approx. W 1500 x H 1400 x D 750 mm - Weight approx. 400 kg
Band width 250 mm, stuffenlos adjustable speed Btto 600 kg ... more information