sheet metal working used for sale

sheet width: 2040 mmplate thickness: 6,00 mmdistance between columns: mmstroke: 300 mmtotal power requirement: kWweight of the machine ca.: 6,00 tdimensions of the machine ca.: 3,25 x 1,50 x 1,80 m- Sharp rail- Bending rail 35 mm- Bending angle adjustment conventionally via potentiometer- Rear sheet metal support arms- Technical documentsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 605 mmplate thickness: 1.50 mmdistance between columns: 605 mmback stop - adjustable: 300 mmtable width: 605 mmoperating pressure: max 6.0 barwork height max.: 1025 mmwork table:: 605 x 250 weight of the machine ca.: 268 kgdimensions of the machine ca.: 1200 x 950 x 1300 mmFurnishing:- pneumatically driven sheet metal shears- manual backgauge- Pneumatic pressure gauge- 2x side table stops including mm scale- 1x movable table stop- Piece counter- mechanical sheet metal hold-down device- Machine light- freely movable foot switch Machine link:https://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machinen o=1008-9325334The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width - max.: 350 mmcoil weight: 1 tcoil internal dia.: 360 - 475 mmweight of the machine ca.: 1 tdimensions of the machine ca.: BxTxH 1500x1500x1900 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... more information

sheet width - max.: 350 mmcoil weight: 1 tcoil internal dia.: 360-475 mmweight of the machine ca.: 500 kgdimensions of the machine ca.: BxTxH 1500x1500x1900 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... more information

sheet width: 3000 mmplate thickness: 8,00 mmdistance between columns: mmtotal power requirement: kWweight of the machine ca.: 6,80 tdimensions of the machine ca.: mMotorized back gauge with fine adjustment via handwheel up to 1000 mmCutting length limitationKnife sharpenedThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

round bar steel: 50 mmsquare edge steel: 40 x 40 mmL-beam: 140 x 13 mmPunch power: 900 kNhole punching press: throat: 510 mmhole punching press: max. length of stroke: 29 mmhole punching press: capacity (dia. x thick.): 31 x 20 mmnotching: l + T material: 80 x 14 mmno. of strokes: 40 / 45 Hub/mintotal power requirement: 4 kWweight of the machine ca.: 3,7 tdimensions: 2,1 x 0,7 x 2,12 mAccessories: various punches and diesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Force of pressure: 150 t working width: 4500 mm clear stand width: 3050 mm stand projection: 300 mm rear gauge: 1000 mm Electr. Supply: 380 V, 18.5 kW weight: 14.8 t space: 4200 x 2000 x 3000/3150 mm  ... more information

sheet width:5040 mmplate thickness:2 mmtotal power requirement:12 kWweight of the machine ca.:9,4 tdimensions of the machine ca.:6200× 1300 ×1900 mmworking width:5000 mmcontrol:Fasti Matik stroke of upper beam:500 mmadjustment of lower beam:u.Biegewange 80 mmcontrol cabinet:1000 x 850 x1450 mmDocuments:vorhanden

Bending capacity at 45 kg/mm2: 2540 x 2 mm 6 angles pre-adjustable Automatic or manual operation Double foot switch 1 additional edge rail 1 additional bending rail wide  ... more information

Max. cutting length: 3,000 mm Max. sheet thickness: 8 mm steel Motorized backgauge with fine adjustment via handwheel up to 1000 mm Cutting length limitation Knife sharpened Weight: 6,800 kg  ... more information

The machine is in good technical condition. Max. length of cut sheet: 2000mm Max. thickness of the cut sheet: 6.3 Weight: 6725 kg Upon prior agreement, the possibility of a tour in progress. ... more information

sheet thickness: 4 mm steel, 3 mm stainless steel Adjustable angle between 30 and 120 degrees Weight: 1.000 kg  ... more information

STROJARNE PIESOK XZMP 3150/6.3C 3-roll plate rolling machine built in Czechoslovakia in 1983 is designed for pre-bending and rolling sheet metal into cylindrical or conical covers and segments. The machine is distinguished by a fully welded structure with increased rigidity and three high-quality 300 mm diameter rollers with longitudinal grooves for easy alignment of the sheet. The bottom rollers, driven by a high-performance motor with two stages of rotation, allow for vertical repositioning during pre-bending and coiling, and also allow for an offset to an inclined position when the claw couplings are opened. As a result, each of the four lower roll bearings can be freely adjusted in the pitch range. The XZMP plate rolling machine has a control panel with a function to monitor the position of the lower rollers directly on the numerical indicators. The total weight of the STROJARNE  ...

material width:500 mmmaterial thickness:0,2 - 3,8 mmfeed length:0 - 9999,9 mmnumber of rolls:2 material cross-cut:128 mm²speed:60 m/minpower requirement:2,0 kWdimensions (WxDxH):1,2 x 1,3 x 1,5 mroll feed:Servo control:Siemens S 7, modification 2002  ... more information

material width:200 mmmaterial thickness:0,8 - 3,0 mmno. of straightening rolls:6 straightening roll diameter:53 mmnumber of draw-in rolls:2 diameter of draw-in rolls:96 mmmaterial cross-cut:400 mm²speed:3 - 15 m/minpower capacity:0,75 kWweight:0,5 tDimensions (WxDxH):1,0 x 1,0 x 1,4 m ... more information

Hydraulic Shear HACO HS 3010 Capacity: 3000 x 10 mm Back gear gauge travel: 1000 mm Year of construction: 1983 Manual adjustment of the clearance between blades Cutting angle: 1° to 3° Voltage: 380 V Dimensions (L x W x H): 4000 x 2100 x 2200 mm Weight: approx 8 T  ... more information

Straightener, straightener, VEB BLEMA GOTHA UBR 20X1600 / 1-10 sheet rolling machine. Machine for straightening sheets up to 20 mm thick and up to 1600 mm wide. The mill was hardly used because it was the second machine in the plant and served as a spare machine. Currently un-exploited. The machine is undergoing modernization, a completely new control system. The possibility of adapting to the customers needs (extension with roller feeders, receiving, the possibility of sanding rolls and rollers, etc.). Technical data : - year of production: 1983 - sheet thickness: 20 mm - sheet width: 1600 mm - upper straightening rolls: 5 pcs - lower straightening rolls: 6 pcs - rolling speed 10 m / min - engine power: 37 kW - engine power: 2 x 18.5 kW - engine power: 1,1 kW - engine power: 1,1 kW - weight: 39150 kg

I offer hydraulic shears not sheet metal marked NTA 3150/10A manufacturer Strojáreň Piesok. The maximum cutting length is therefore 3150 mm and the strength of the structural steel sheet is 10 mm. Plugged in, fully functional, but so rarely used that its not worth my while to keep them. (they do not fit into our primary production segment) Price negotiable, buyer arranges transport, total weight 14,000 kg Possibility of viewing, testing - at the Chrudim facility

sheet width: 3000 mmplate thickness: 10 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... more information

sheet width: 1500 mmplate thickness: 4 mmback stop - adjustable: 10-1000 mmno. of strokes: ca. 20 Hub/mincutting angle: 1 °table height: 850 mmtotal power requirement: 8 kWweight of the machine ca.: 3300 kgdimensions of the machine ca.: 2500x2000x2000 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.